Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

Allocations + issuing received parts + (Populate the allocate column for each part … Populate the allocate column for each part in accordance to the pick bins that are available. The general rule is to prioritize allocation to the range of Bins of the Build numnber which is next to in line to be Built according to the production schedule. If there is no bin physically available for the Job car number shown it must be zero'd in the allocation quantity column and put into stock normally.antity column and put into stock normally.)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Position module A in front of module B Use Infeed back fence to Multi head datum rollers as initial alignment guide for Y axis Set gap of 23mm -+ 2mm between module A roller frame and module B roller block)
Runing MRP + (Press the Planning Tab > Read demand > ok The demand will then read with a load screen. Once this has finished move on to the next step)
Programming Eaton DE Drive + (Set these references P-20 to P-23 to 50Hz so it will not matter what input 3 or 4 is set to - it will always be 50Hz)
Flowline Turret Upgrade - Somatec + (Remove all parts from the existing turret, to leave just the mounting plate and the cylinder and fittings etc, as shown)
R0000711 Rotary Base Assembly REV2 + (Rotary drive ring needs checking before f … Rotary drive ring needs checking before fitment.
#Check teeth for burrs, damage and debris. Use compressed air to clean all areas #V edge should be checked for damage. Check entire circumference with fingers to identify any damage, lumps or high low spots #Check drive ring has been countersunk in the shown arearive ring has been countersunk in the shown area)
Fitting Zx5 Crank Upgrade + (B0001166)
X252 Forward Clamp Out Sensor Setup Stuertz Infeed + (Select Q1)
Placing a TwinCAT3 Machine Under Source Control + (See this tutorial for backing up (archiving) a TwinCAT3 project)
PLC Source Control - Adding a Repository + (Select View From the Drop-down menu select Team Explorer)
Client Installation of Sage and Cim50 + (Navigate to \\mainserver\Cim50\Updates)
Saje uPVC Unloading Process + (Including the chop saw table Leaving a clear route for the 2.4m x 7.5m table to roll in)
Dokit - Creating A Work Instruction + (To create a new Dokit, you need to login as a editor The Username is Gareth Green Password is available from the IT department <br/>)
Dokit - Editing Work Instructions + (The dokit references for work instructions … The dokit references for work instructions are tracked and stored on the monday board [https://stugaltd.monday.com/boards/3628350043 Work Instruction Dokit Tracker] Check to see if the instruction is already there using the search, there should be a link for it in the link column which will take you straight to the page. If it does not exist, it needs to be created first with this tutorial [[Dokit - Creating A Work Instruction]][[Dokit - Creating A Work Instruction]])
Beckhoff AX8000 Flowline Upgrade + (The first step does not involve being on s … The first step does not involve being on site or carrying out any physical tasks. However, trying to gain some familiarisation before carrying out the upgrade can save time and confusion down the line. Please read through this tutorial before upgrading the machine. The attached files and steps will walk you through the upgrade that somebody else has already experienced. This will give you a free look at any issues or learnings that have already been made. or learnings that have already been made.)
Toshiba - B-EX4T1 Printer Setup + (To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up.)
TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The laser should be aligned to ensure the … The laser should be aligned to ensure the beam is level up / down and parallel to the backfence. The path should follow the Yellow edge of the lift rollers on the infeed table. Length feedback from the measurement system is visible all the time on the service form.
# Measure and mark the infeed table at fixed positions from the loading fence at MH end – (3m, 4m, 5m, 6m) # Use a short offcut of profile with a label on the end to act a a fixed reflector at the marked positions – check against the feedback on the screen. # Adjust the lengthMeasureOffset parameter to get the screen measurements to match reality (+/-10mm)e screen measurements to match reality (+/-10mm))
ZX5 Transfer Table Crank set up + (Follow the instructions in [[Programming Eaton DE Drive|this]] … Follow the instructions in [[Programming Eaton DE Drive|this]] tutorial.

...It is vital that the Eaton drives are programmed correctly as the distance the cranks travel and the time they take to stop depend on the acceleration and deceleration of the drive.

...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.

xt">...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.</div> </div><br/>)
WinDelay for Twincat Startup + (This can be downloaded from Dropbox (Stuga Machinery Ltd)\Service\WinStartDelay\winstartdelay.zip)
R0015278 Mount Completed Assemblies + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
Air Pressure Switch Setup + (This is usually called 'AIR'. From this point you will either need to have somebody watch the input on the screen or have means (eg dialled in on a laptop) to be able to watch the output while carrying out he next step.)
Fitting R0019199 Upgrade: Autoflow Slewing Ring Guard Kit + (This procedure must be done in conjunction with moving the SR Axis Datum to a position higher and ant the front of the machine to [[Move SR Datum Sensor to Higher Level R0019217]] <br/>)
ZX5 V Notch Blade Mechanical Setup + (Using a straight edge placed BETWEEN the t … Using a straight edge placed BETWEEN the teeth of the blade (W/I) you can see we have a gap around 2-3mm. On the opposite blade (W/O) we need to turn the setting bolt anti clockwise until the tips of the teeth just touch the straight edge, as seen in the second picture. If the tips of the teeth were overlapping we would need to increase separation by turning the adjusting bolt clockwise. Transfer the straight edge to the opposite blade (W/O) and adjust W/I as above.
lade (W/O) and adjust W/I as above. <br/>)
Diagnosing EtherCAT Issues - Advanced + ( #Choose the device network to interrogate … #Choose the device network to interrogate and press the Advanced button #Expand to the Diagnostics-Online View and select the CRC checks 0300-0304 and Link Lost 0310-0312. Click ok to exit #On the online view, the system now records more detail about the CRC errors or link lost problems. In the case in the pictures, FB015B has recorded 69 errors on issue 0310 , which is "Link Lost A/B". There are CRC errors on the output of FB016B and the input of FB015B. This tells me that the link between FB016B and FB015B is not reliable. Could be a loose connection on the etherCAT and / or power cable ection on the etherCAT and / or power cable )
Autoflow Mk1-Mk3 Daily Maintenance + (To check the machine is ready for producti … To check the machine is ready for production, a couple of simple tests can be run # Datum Test # Pos Test

...Do not attempt to make any adjustments to the machine on the basis of one test. If there is an error, run the test again twice more. !! Adjustments are only effective if the error is repeatable !!

...The machine tolerance is +/0.5mm, so there is no need to adjust if an inaccuracy is less than this tolerance (1mm back to back)

olerance is +/0.5mm, so there is no need to adjust if an inaccuracy is less than this tolerance (1mm back to back)</div> </div><br/>)
Units of Measure modification CIM50 + (To make the item status of a product inact … To make the item status of a product inactive it needs to comply with all of the following conditions : Item has 0 in stock Item has 0 in quarantine Item does not exist on any live sales orders Item does not exist on any live purchase orders Item does not exist on any live works orders Item does not exist on a bill of material

Please make a note of changes that are made stock levels allocations P.Os Works orders or BOM lists are amended to make an item inactive as these will have to all be re-entered after the unit of measure has been amended and saved.

e re-entered after the unit of measure has been amended and saved.</div> </div><br/>)
OBSOLETE DM - Updating Resources + (To open the document go to the Stuga dropbox (ask admin for permissions): Service > Documentation > Device Magic Resources > DeviceMagic Data v1.xlsx https://www.dropbox.com/s/v7vhxpve9ocm6as/DeviceMagic%20Data%20v1.xlsx?dl=0)
R0015251B Bench Assemble X Axis Energy chain + (1 Assemble 111 links together , ensure all links are orientated the same way . 2 Identify the female end of the assembled links 3 Fit 2 more links of A0001113, but fit in a reversed orientation)
TB0385 Upgrading to winMulti v6 + ( (Defaults to Config mode after the TwinCAT update))
Setting up NAS Server - MyCloud EX2 + (Use IPScan to find the address)
R0015114 Bench Assemble Valve Banks and Regulators + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015096 (c) Bench Assemble Transfer Drive Assembly + (Use Loctite 243 on all fasteners Use Loctite 572 on all pneumatic threaded connections Pen mark all bolts to show finalised)
R0015352 Mount Buffer Beams + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015060 Bench Assemble Flapper Beam + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0000738 Pneumatic Installation Part 3 + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015343 Waste Guidance Installation + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015272 1st Stage fitting Saw Outfeed + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0015315 Fit Y Axis Drive components + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised <br/>)
R0015292 Install Cylinder Rails and Align + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015342 Bench Assemble Outfeed Parts + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0000738 Pneumatic Installation + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015011 Bench assemble Gripper + (check shafts fit correctly into bores of D0015082 gripper bottom bar and D0015083 gripper upper bar)
R0002916 Install Machine Trunking + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015028D ZX5 Hepco Beam Alignment Module C + (Ensure additional spacer is removed from jigs when using for alignment on module C)
R0015004 Bench Assemble Gripper + (1 Fit bushes B0001106 (20 off) to 8 off D0015095 link bars 2 off D0015096 link bars 2 Fit bearings B0000034 x 2 into D00015086 grip slide body. Use grease to lubricate bearing before assembly)
R0015299 Install Spindle control pipework and fittings + (Use Loctite 243 on all fasteners Pen mark all fasteners to show finalised)
R000718E Stage 2 spindle assembly + (Use Loctite 243 on all fasteners Pen mark bolts when finalised)
R0015358 Conveyor chassis + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015096 (e) Bench Assemble Transfer Drive Assembly + (Use Loctite 243 on all fasteners Use Loctite 572 on all pneumatic threaded connections Pen mark all bolts to show finalised)
Autoflow Maintenance - Infeed + (Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds)
J0001000H Autoflow Mk4 Mechanical installation-Alignment + (Use footprint drawing to determine machine location for installation)
R0015298 Bench Assemble V notch Clamps + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015063 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015273 Module E support arm alignment + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015090 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015245 Module C support arm alignment + (1 Move channel 2 section up or down to co … 1 Move channel 2 section up or down to copy height of adjacent channel 3. Use the tabs as the reference points 2 Use 2 meter straight edge and level between points indicated Move channel 2 at the end indicated, to give a level reading 3 Tighten bolts to hold in place
3 Tighten bolts to hold in place <br/>)
R0015321 Bench Assemble Guards and Doors + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015038 Bench Assemble V notch Datum Rollers + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015332 Mount Backfences and Align + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000963E Bench Assemble Z axis Components + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015312 Finalise V Notch Subframe + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000572 Bench Assemble Centralise Assembly + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015311 Install and Align Datum rollers + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015007 Bench Assemble Roller Tables Machining Outfeed + (13 off Check part D00150001 has been supplied to new specification Check indicated hole, should measure 8.2mm. If not open up with hand drill Drawing change requested 06/06/23 to amend from 8mm to 8.2mm <br/>)
R0002913E Install and Align Rotary head Subframe + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015079 Infeed extension assembly + (1 Fit levelling jig to frame extension section as shown 2 Use engineers level to adjust the level with the floor jacking bolts to set the jig level)
R0015266B mount completed assemblies + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015078B Module A infeed arm alignment + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015247 Fit X axis gearbox and Motor + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
R0015121 Bench assemble Infeed arms + (Use loctite 243 on all fasteners Pen mark all fasteners once finalised)
R0015255 Mount Assemblies to Main Frame + (Using the first point used to set the brac … Using the first point used to set the brackets , measure the gap indicated and replicate this measurement on the other 4 points . This is adjusted by moving the indicated bracket up or down .

...If enough adjustment isnt available on remaining positions, first position can be moved up and new measurement taken

sitions, first position can be moved up and new measurement taken</div> </div>)
R0015030B Bench assemble loader wheel + (Attach cylinder mount block D0010238 to assembly with 4 off M6 x 20 socket caps)
PLC Source Control - Selecting GIT as the source control Plug-in + (When the error message : "Git is not the current Source Control plug-in" appears # Select the link to change the Plug-in)
Autoflow Maintenance - Gripper + (Wipe away any excess oil, dirt or swarf. Apply oil lubricant and wipe of excess # Main X axis slideways # GY Gripper Y axis Slideway # GZ Gripper Z axis slideway)
Changing the Flowline Ops Password + (Within FlowlineOps click on the unlock Button in the toolbar, you will be required to enter a challenge password to enter this area, this can be obtained from https://www.stuga.co.uk/unlock-code/)
Gripper Push Speed on Flowline and ZX + (You can adjust the Flow control and Slow d … You can adjust the Flow control and Slow down the cylinder speed. The one you need to wind IN (clockwise) to slow down is the one nearest to the MH side - Not the Extractor side.

...Note, the photo is from a Right to Left feed machine, the video is from a Left to Right feed machine

feed machine, the video is from a Left to Right feed machine</div> </div><br/>)
TB0431 Samsung Drive Parameter Setup + (Using a stripped plug and making sure ther … Using a stripped plug and making sure there is no power going through the plug during installation: # '''Live wire''' (Brown) in the top port # '''Neutral wire''' (Blue) in the second port # '''Ground wire''' (Green + Yellow) in the bottom port # The '''Joggers''' Serial port # Plug in and '''turn on''' plugial port # Plug in and '''turn on''' plug)
Removing TwinCAT3 Interpolation Licence + (You will get an error message saying a licence has expired. In the project view under licences, you will see TF5100 (TC NC I) expired)
Z Transom Width Measurement + (A straight faced piece of profile the same height as the Z section or taller or a piece of steel straight edge or the like; then lastly a Z section profile for measuring.)
Convert TC2 Project to TC3 + ( #Open Visual Studio #Create a new TC3 pro … #Open Visual Studio #Create a new TC3 project called [BuildNo] in c:\TwinCAT\Stuga\ #Make sure "Create Directory..." is Unticked #Right Click on the project name and select ‘Load Project from TwinCAT 2.11 Version…’ #Click Cancel on the two windows asking to convert the PLC project #Ignore or cancel any warnings about libraries (this part will be replaced later)

...Once created, you will have a copy of all the devices and boxes in the project with the correct naming.

f all the devices and boxes in the project with the correct naming.</div> </div><br/> )
Filling Out An Online Daily Timesheet Form + (You will receive a link via email that wil … You will receive a link via email that will open up your timesheet. Copy the link from the email and paste it into a new shortcut on the desktop of the device you are using. The shortcut should be labelled 'Timesheet' for clarity. To create the shortcut, right-click on a spare area on your desktop and hover over 'New'. This will open a selection panel. Select 'Shortcut'. A text box will appear and this is where you need to paste the link from the email. Once you have pasted the link, select 'Next'. A prompt will will then ask you to name the shortcut. I would suggest that it is named 'Timesheet'. After naming the shortcut, click 'Finish' and the shortcut will appear on your desktop. Double-click on the shortcut to open up your timesheet form.e shortcut to open up your timesheet form.)
Changing Version Control to Visual Studio + (Delete the versionControl folder completel … Delete the versionControl folder completely

...This prevents confusion in the future of where the project exists

prevents confusion in the future of where the project exists</div> </div><br/>)
Autocut Regular Maintenance + ([[Autocut Open Guard Doors|https://stuga.dokit.app/wiki/Autocut_Open_Guard_Doors]])
Autocut Monthly Maintenance + ([[Autocut Open Guard Doors|https://stuga.dokit.app/wiki/Autocut_Open_Guard_Doors]])
Stuga Product Database - Edit Product Data + (Search box is upper right)
R0015278 Mount Completed Assemblies Section two + (these steps follow on from dokit [[R0015278 Mount Completed Assemblies]])

Hikvision Camera Setup + ( # The initial screen is the '''Live View' … # The initial screen is the '''Live View''' # '''Playback''' is where recordings that are saved to the SD card are viewed and downloaded. # '''Picture''' (is not used) for the snapshot function. # '''Configuration''' used to change settings and set up SD card. used to change settings and set up SD card. )

TB0314 Updating Mint File in Workbench + ( # Contact Stuga service to download latest version to the machine via teamviewer # On the g:\ drive G:\Builds\Latest Software Versions. # From Dropbox service\Machine Software\ )
Ensuring Mapped Drives Connect Every Time on Startup + ( # Go to C:\\Users\Stuga - From here we need to go to 'View' and tick 'hidden items' to show folder 'App Data' # Navigate to C:\\Users\Stuga\App Data\Roaming\Microsoft\Windows\Start Menu\Programs\Start up )
VM Upgrade Software + ( # Install the VM Upgrade hardware [[VM Upgrade Hardware]] # Check that you have at lease 12GB of memory. # Check that the extra disk is present (Should be D) )
Updating Teamviewer Host + ( # Right click on the teamviewer icon in the taskbar (bottom right of screen) # Select Exit Teamviewer )
OBSOLETE Installing SourceTree Version Control Software + ( #Download [http://sourcetreeapp.com/download/?v=win here] #Agree to Ts&Cs <br/> )
TM018B Microline and ZX3 V Notch Blade Setup + (A calibration mnd file has been written to … A calibration mnd file has been written to help line up the x offsets called VTEST. This program creates the following pattern on the bottom of the profile using a 10mm spindle and the notching blades themselves: Run the VTest operation on a length of large outer frame of at least 1m long. Put the operation at a position of 500mm. The pattern allows you to measure the offsets required with calipers.

...Profile is viewed from the bottom face, Basically turn it over when it comes of the transfer table.

face, Basically turn it over when it comes of the transfer table.</div> </div><br/>)
R0000164 Spindle Disassemble for Required parts + ( #Remove 2 off M6 grubscrew from pulley #R … #Remove 2 off M6 grubscrew from pulley #Remove pulley from shaft

...If pulley is tight to remove, use lever bars to prise pulley off

pulley is tight to remove, use lever bars to prise pulley off</div> </div><br/> )
Hikvision Camera Setup + (<div class="annotatedImageDiv" typeof=" …
On the machine open the “SADPTool” . This is our camera finder and IP address modifier for the cameras)
ACEpc Changing IP address using netedit + (This is supplied by customer. IT department <small>''If testing in house it needs to be on the 192.168.16.xxx range.''</small> <small>''e.g 192.168.16.101''</small>)
Upgrade ZX Machine to Beckhoff Drives and Control + (Before the upgrade is despatched to site, … Before the upgrade is despatched to site, the servo system needs to be assembled and pre-wired in its enclosure.
*Drill off Fan detail in right hand side of cabinet. A 114mm hole saw and arbor has been purchased for this. *Drill and fit 4 adjustable feet in the bottom of the cabinet. 4 extra nuts will be in the kit. The height of the feet does not need to be set at this stage. *Drill off all servo drives. For ZX3 machines, the rack will be as follows: AX8640-AX8118-AX8206-AX8206 and for a ZX4 the will be: AX8640-AX8118-AX8206-AX8206-AX8206 (the extra drive is for the V and W axes). *Pre-wire the rack (inc STO links) and the cabinet fan with the cable provided in the kit. leave the spare coil of cable in the cabinet ready for running on-site. *Plug in the 2x15m green etherCAT cables. *The enclosure bottom plate is left off to allow the cable entry on site. '''''*for detailed wiring information, please use drawing packs from Monday.com board.*'''''e use drawing packs from Monday.com board.*''''')
Setting Up Email Production Reports + (Navigate to Settings->Parameters)
Installing VNC Server and Viewer + (<nowiki>From the piggy back PC, conn … From the piggy back PC, connect to
\\Bnnn\
or
\\Bnnn\saw
[Where Bnnn is the build number - eg M012, F002 etc]
on the older PC.

If using the build number does not work, you may need to use IP addresses
\\192.168.1.54\saw
(Look up the IP address using ipconfig from the command prompt, or network settings)

sing ipconfig from the command prompt, or network settings)</pre></div><br/></nowiki>)
Autoflow Maintenance - Outfeed Table + ( * Clean Stainless Steel Bed of swarf and … * Clean Stainless Steel Bed of swarf and remove any tape that may have transferred onto the bed during normal operation * Lightly oil shaft on underside of bed, lightly oil cylinder rods * Lghtly oil Hepco rail, 1 -2 pumps of grease into Linear Bearings * Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds * Check Hepco rail, Linear Bearings, Shafts and cylinders for damage or wear gs, Shafts and cylinders for damage or wear )
Setting Up Windows PC C0000422-KIT 2023 + ( * Connect Keyboard and mouse * Connect network * Connect monitor )
Updating the Touchscreen Driver + ( * Go to Control Panel > Programs and F … * Go to Control Panel > Programs and Features > Uninstall a program * Scroll to 'EloMultiTouch' and click uninstall. Touchscreen will still work at this point as the Windows system takes over. However the new one still needs to be installed to allow for calibration. l needs to be installed to allow for calibration. )
Setting Up C0000422-KIT - Full Hardware 2023 + (Remove the PC from the Dell box with power adapter and power cable. Keyboard and mouse (if supplied) can be returned to stores (not needed here))
Upgrade Autoflow to Windows 10 + ( *Ensure regional settings correct - corre … *Ensure regional settings correct - correct date format *Rename the Ethernet Adaptors to Ethernet and EtherCAT *Ensure the [https://stuga.dokit.app/wiki/TwinCAT_Issue_-_EtherCAT_Network_Protocol_Missing TwinCAT Protocol is installed] on the EtherCAT adaptor *Teamviewer setup *Administrator password set to "Stuga001" *Add Stuga desktop image *Latest winMulti in c:\multi desktop image *Latest winMulti in c:\multi )
PC Recovery Process + (- Turn off the PC - Plug in recovery USB. - Turn the PC back on - Keep pressing F12 until the boot selection screen shows. <br/>)
R0000204 Notching gear boxes assembly + (It is vital for correct function that all … It is vital for correct function that all the shown components are thoroughly degreased before assembly . To do this, wash all parts with FE10 solvent spray and dry with airline.

...Ensure your work area is very clean and free from Dust/swarf. Use a clean cloth or paper towel to lay on your bench to ensure parts remain clean once washed

o lay on your bench to ensure parts remain clean once washed</div> </div><br/>)
Zx5-Zx 4-Zx3-FL-S65 Saw Blade Removal and Refitting + (1 Open front door via control screen 2 Ensure emergency stop system is also activated for safe working 3 Remove swarf from saw)
TB0444 Renewing CF Card on TwinCAT2 Systems + (1. From Camera PC, use System Manager … 1. From Camera PC, use System Manager to activate original configuration 2. From Camera PC, use PLC Editor to login both original projects – PLC_Reset in Port 811, and the other main PLC control project in Port 801.

DO NOT FORGET TO ACTIVATE BOOT PROJECT

instructions-text">DO NOT FORGET TO ACTIVATE BOOT PROJECT</div> </div><br/>)
TEST JAMIE B + (<big>This means prepping the changing area so everything is in reach.</big> *(6) Nappies *(2) Baby wipes *(3) Nappy Bag *(4) Change of clothes *(5) A toy (Distraction) <br/>)
Ecoline - Disabling V axis To Swap Faulty Drive + ([[Archiving a TwinCAT Project]])
WinMulti Shutdown procedure + (Once you have a black screen with a small blue text box in the middle you are safe to press the physical red 'POWER OFF' button on the console.)
Turning Off and Changing Datum Tool + (<div class="icon-instructions dont-icon"> <div class="icon-instructions-icon"><i class="fa fa-hand-paper-o"></i></div> <div class="icon-instructions-text">Do not alter anything on the 'Tool' Settings' side.</div> </div><br/>)
Create a TwinCAT Project from Scratch + (<div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...From Z071 there is no twinSAFE project as the Estop circuit is hard wired</div> </div>)
Viewing Camera Footage from Hikvision Cameras + (If this is the first time that this has been attempted on your PC, a Hikvision plugin will be needed. Follow the process to install it)
Disabling a Tool Home or Tool Out Sensor + (A change has to be made to one of the setup files, so you need to exit to the desktop)
Importing Picking List from Sage To Monday + (A pick run is a chunk or set of Job Cards that will be picked in a controlled amount. This is normally 10-20 job cards. it is managed in this way to keep the amount of time between the allocation on Sage and the physical pick as short as possible.)
Guide to Fitting Eject Push Sensors on ZX Machines + (A retrofit kit will be sent with all the p … A retrofit kit will be sent with all the parts needed to carry out this task. The assembly number for the kit is R0019218. If you have any feedback regarding this kit, please use this assembly number. It is important to check the parts you have received against the assembly list to ensure you have nothing missing before starting the job.e nothing missing before starting the job.)
Commissioning - Off-Cut Laser Sensor + (Adjust the "'''Light Dark'''" balance on t … Adjust the "'''Light Dark'''" balance on the sensor. To do this, using a small flat head screwdriver, turn the light dark dial '''clockwise''' until the orange light goes off. Then slowly turn '''anti-clockwise''' until the orange light turns on again, when this happens re-turn a '''little clockwise''' to turn off the orange light.clockwise''' to turn off the orange light.)
R0000712E Rotary Trunking + (All bolts must have Loctite 243 adhesive applied unless otherwise stated. All bolts must be marked with pen once completed to indicate adhesive and correct tension has been applied)
R0015041 Bench Assemble Top Hood Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305 Install Wiring loom for Rotary loom + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R0015064 Bench Assemble Clamp Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015037 Bench Assemble SY Assembly Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015081 Bench Assemble Single Roller Table + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015037 Bench Assemble SY Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0000571 Fit and Level Cut Tables , Finalise Eject + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015146 Pneumatic pipe Installation Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015100 Fit Guarding + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation Part 3 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0000574 Fit Motor and Swarf Chute + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015330 Fit 1st stage Ejector and Level Base + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305A Install Wiring loom for Rotary Ring + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R0000558E Bench Assemble Base and Turntable + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015334 Fit Centralise Front Table + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
Setting up an Ecoline Barcode Scanner + (All refurbished Ecolines will now be provi … All refurbished Ecolines will now be provided with USB barcode scanners. This may be a hand held device or an 'Orbital' scanner attached to the infeed table depending on the customer's preference. Use the provided cable to plug the scanner in to the nearest available USB port. There will be 2 USB extension cables coming from the PC inside the cabinet. One will go to the console to control the keyboard and the touchscreen and the other will go to the infeed table junction box to control one or two barcode scanners.ox to control one or two barcode scanners.)
R0015029D Hepco Beam Alignment + (Always Use Loctite 243 on all fasteners Always use Loctite 570 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
R0000299 Stroke assembly rebuild Part 2 + (Always use Loctite 243 on all fasteners fitted unless stated different All bearings should be an acceptable fit, with Loctite 641 and FE10 solvent used if required All fasteners should be marked once finalised)
Commissioning a Beckhoff Axis + (Ensure the axis.mul file is set up with the same axis Ids as the TwinCAT project Second number in axes.mul file)
R0015382 Top Spindle Blower Upgrade + (Assemble Valve and Y connector as shown)
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Before installing module B, module C rolle … Before installing module B, module C roller tables should be double checked for correct positioning 1 To do this inspect tables 1, 2,3 and 4 for level as shown. 2 Also inspect alignment with 2 meter straight edge. All rollers should be on the same height and no bump up should be present when moving the straight edge over the table. 3 Ensure fixed table is at same height as rollers Report any discrepancies to supervisor for correct remedial action to supervisor for correct remedial action)
Updating Zebra Firmware on ZD620 model + (Both the zip files for the install of the Zdownloader and the ZPL version file can be located in G:\Builds\Install Files\Zebra Firmware. there is a manual for using the Zdonloader in with the zip file containing the ZPL version file .)
R0015295 Finalise wiring loom for Rotary head + (Cables must be adjusted between each spind … Cables must be adjusted between each spindle to ensure the cable lengths are correct . 1 Start at cable point between 6 and 5 . Start with the light green ethercat cable with the right angle plug. Adjust so that 200mm is past the end of the spindle plate . See picture for detail. 2 Move to the next spindle connection between 5 and 4 and adjust the new right angled ethercat cable to match the length of the previous adjusted cable 3 Repeat this process working your way around the spindles to set all ethercat cablesnd the spindles to set all ethercat cables)
ZX5 Installation Procedure 2023 Part 2 + (Check X axis alignment of horiczontal and … Check X axis alignment of horiczontal and vertical rollers using 2 meter straight edge and feeler gauges Any discrepancy must be reported and rectified if present Tolerance 0.002" / 0.05mm [https://stugaltd.monday.com/boards/3628350043/pulses/4665028475][[R0015311 Install and Align Datum rollers]]
[[R0015311 Install and Align Datum rollers]] <br/>)
TB0409 Setting Up Windows 10 PC 2018 + (Connect monitor, network cable, keyboard, mouse/touchpad, and switch on PC.)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Position module F at end of Module E infeed frame Approximately Align Saw roller back fences to Saw infeed back fences Approximately align X axis position by setting the to frames spaced at the distance shown of 20mm)
PLC Source Control - Working with GIT and TcXaeShell + ( #Select '''Push''' #Message appears showing the successful push to the '''Origin''' which is in the remote cloud Repo )
Batch Printing Part Drawings + (Double click on the P.O the drawings are required to be batch printed for.)
GY GZ axis setup with Jetter Motors + (Ensure that the profile support arm is held out of the way to avoid marking the blue infeed arm.)
Autocut Startup Procedure + (Ensure the main isolator on the console is in the on position (pointing up).)
ZX5 Transfer Table Setup + (The rollers on top are mounted on eccentri … The rollers on top are mounted on eccentric bushes. We only need these just tight enough to not allow any slop or vertical play. Slacken the cams off completelely, you will need an 8mm spanner with the faces ground down to fit in the space. Slide the plate onto the rail and tighten the eccentric bushes until any vertical play is removed. Lightly try to move the assembly on the X axis, if there is any slop then it needs to be a little tighter but probably no more than an 1/8th of a turn. Once set you should still be able to spin the rollers by hand, but still feel a fair bit of resistance. Once set slide the assembly over the full length of the V rails to check fo any tight spots. If there are then you need to check that the two halves of the fail are fully mated!!! two halves of the fail are fully mated!!!)
AX8000 Drives - ES Contactor Wiring + (Find a spare section of DIN rail that the contactor can be placed in. The contactor clips onto the din rail without the need for fixings.)
Recovery of Bar Queue following winMulti Crash + (First you need to check out the bar queue … First you need to check out the bar queue to see if it is the same as the actual bars on the transfer table #Restart winMulti #Count the total number of bars on the saw infeed and transfer table #Compare with the number of bars on the saw queue

...If you have some offcuts on the screen, this can help identify the queue position by looking at the length of the offcut

If there is '''one more bar''' actually on the table than on the bar queue screen, follow the process below to add the missing bar to the queue.han on the bar queue screen, follow the process below to add the missing bar to the queue.)
VSM 20-30-P VertiQuad Heater Plate Setting + (First, make sure the heater plates are coo … First, make sure the heater plates are cool enough to work on. If not then gloves will be required to protect your hands from the heat Put the machine into input/output mode. This will then allow us to move the heater plates into a position to be worked on. Ensure the items highlighted in GREEN are on.ure the items highlighted in GREEN are on.)
Autocut Adding New Profile + (Firstly, we need to make sure that the pro … Firstly, we need to make sure that the profile will physically go through the machine, open the top gaurd door. Ideally, you will have a 1 metre offcut of the profile - work out the best way for the profile to go through the machine. Push the profile through the machine by hand to ensure no catching areas etc.e by hand to ensure no catching areas etc.)
R0015350 Fit Rigid Ducting + (Fit ducting as shown 2 off M0001228 1 off M0001213 1 off M0000118)
TB0425 Lenovo Tablet Setup + (Go to the PlayStore and download the e-Drawings app. This will cost (currently £1.25) therefore ask appropriate member for a company card.)
Troubleshoot - Permanent IP Address - Windows 8 + (Go to '''Control Panel > Network and Sh … Go to '''Control Panel > Network and Sharing Centre'''.

Alternatively you can access the Network and Sharing Centre by right clicking the network icon in the bottom right toolbar on the windows desktop (see picture).

the bottom right toolbar on the windows desktop (see picture).</div> </div><br/>)
Troubleshoot - Permanent IP Address - Windows 10 + (Go to '''Control Panel > Network and Sh … Go to '''Control Panel > Network and Sharing Centre'''.

Alternatively you can access the Network and Sharing Centre by right clicking the network icon in the bottom right toolbar on the windows desktop.

the network icon in the bottom right toolbar on the windows desktop.</div> </div><br/>)
ZX5 Adjusting V Notch Depth and Position + (If the blades do not meet properly, or form a "W" shape, the mechanical setup is not correct. Please follow procedure: [[ZX5 V Notch Blade Mechanical Setup|https://stuga.dokit.app/wiki/ZX5_V_Notch_Blade_Mechanical_Setup]] <br/>)
Stuertz Welder - Setting Barcode Reader + (If this is a Zebra scanner, the Zebra CDC scanner program will be installed already. For other manufacturers, this may need to be downloaded from the internet <br/>)
ZX5 Installation Procedure 2023 + (Identify if either saw infeed or multi head outfeed is the logical frame to place first . Consider access to machine when installing 1st frame Consider handing of machine)
Setting Motor Overload Relays + (In order to read the motor plate we need t … In order to read the motor plate we need to know 3 pieces of information *Whether the motor is wired in star or delta *The frequency at which the motor is running *The voltage at which the motor is running Whether the motor is wired in star or delta depends on the application. Refer to the electrical diagrams to find out which it is. For example, the saw blade motor is wired in star, whereas most extractor motors are wired in delta. The UK standard for a three phase electrical supply is 415v at 50Hz. Unless the supply to a motor runs through an inverter (i.e the spindles) this is also the standard for our machines. Using the picture on the right as an example, we know the motor will be running at 50Hz (1) so we can disregard the information on the right of the plate as this provides figures for a 60Hz supply. Looking at the box numbered (2) we can work out that this motor would be wired in delta if it were running on a single phase 230v supply. However, we know that this is a three phase supply and will be wired in star. So when we move on to the box numbered (3) we will be looking at the number on the right hand side of the slash. Therefore, this particular motor would need an Overload Relay set to 3.00A.would need an Overload Relay set to 3.00A.)
R0015280 Module E Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed * Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testinglies are at a sufficient stage for testing)
R0015257 Module C Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed
* Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testingassemblies are at a sufficient stage for testing)
Fitting M8 Plug for EtherCAT Boxes + (Inside the packet of the plug will be 5 co … Inside the packet of the plug will be 5 components: 1- Metal outer shell 2- Numbered insert 3- m8 IDC connector 4- Individual 'white' grommet 5- Additional 3 grommets

...The 'white' grommet and numbered insert may be stuck in the metal shell. Please check!

Make sure you check that you have all of these parts before disposing of the packaging.gt;Make sure you check that you have all of these parts before disposing of the packaging.)
Flowline 6 to 6o5m Extension + (Clean and remove any dirt/grease/imperfections on the box section ready the the new rails. If any of the tapped holes are compromised, re-tap 6mm.)
PC Bios Power settings + (Keep pressing the “DELETE “button on the k … Keep pressing the “DELETE “button on the keyboard until the PC goes into the BIOS mode and you see a screen similar to the ones shown below. If the BIOS screen does not show wait for the PC to LOGIN into windows and then shut-down or restart the PC again and retry using the delete button as described above. The Menu Will look something similar to thise Menu Will look something similar to this)
R0015307 Bench assembly spindle drive cylinders + (8 off P0001200 cylinder Use Loctite 572 on all air fittings 1 Attach P0001098 elbow as shown 2 Attach P0001198 elbow 3 Attach P0000238 elbow <br/>)
ZX5 MH Infeed Basic IO Test and Setup + (Make sure the reset of the Estop circuit w … Make sure the reset of the Estop circuit works. Be aware when resetting this will reset the air to home all pneumatics. Test each emergency stop button individually (Button box, infeed rear middle and end) making sure this breaks the circuit when pressed and the air is dumped. The Infeed beam sensor should be tested, when broken should also break the circuit and dump the air. Check on Service menu - IO tab that each input works correctly for each Estop unit.input works correctly for each Estop unit.)
Changing Main Saw Blade + (Make sure you have stopped cutting and nothing on the machine is moving - press an emergency stop button to ensure this.)
C0001005MM Micromech Stepper Motor Assembly + (Mark the motor face as the picture to give … Mark the motor face as the picture to give the correct mounting position A 3mm hole must be drilled in this position at a depth of 5mm . Caution, damage can be caused to motor if this depth is not adhered to. Increase drill sizes incrementally when drilling, to ensure a good sized 3mm hole Use masking tape to stop swarf entering the stepper motor housing Use a drop of Loctite 270 to ensure dowel remains in place when fitted ensure dowel remains in place when fitted)
R0015276 Line up slider units and mesh racks + (Mesh requires setting between slider unit … Mesh requires setting between slider unit and drive pinion 1 It is vital that the correct drive meshing is achieved. 2 Once set, there should be 1mm movement in the direction shown, which will indicate the correct tooth meshing has been obtained. 3 This need to be checked at all points of travel as showne checked at all points of travel as shown)
B0000082b Motor replacement For Obsolete part B0000082 + (New motor B0000082b will need modification of drive key to function correctly. 5mm should be removed from key in situ as shown in photo This will enable clutch plate to move to desired position on assembly)
ZX5 Datum and Grip Pin Setup + (In SETTINGS > PARAMETERS > MEASUREMENT > loadingPos=11 If set at a different figure, update to 11 and SAVE)
Monday - Obtaining Customer or Machine Address from a Job + (On Apple - Select View Item On Android - A subform opens with the Machine at the bottom, click on the Machine here to open the next subform)
Commissioning - Z-Block Calibration + (On the '''Service > IO''' tab use output '''Y214''' to turn the infeed turret. <br/>)
Updating Beckhoff TwinCAT3 Backend Version + (On the desktop of the Beckhoff PC, right c … On the desktop of the Beckhoff PC, right click the Twincat Icon in the taskbar and select "About Twincat..." TwinCAT version is displayed. 3.4024.xx is needed

...The .xx is the build number. Generally, all .xx will be compatible, they release a new build number for bug fixes but will change the main version number when it becomes incompatible

change the main version number when it becomes incompatible</div> </div><br/>)
Easily resizable forms for any screen resolution in Visual Studio + (On the start screen in Visual Studio, click on the "Create a New Project" button.)
R0015248 Line up slider units and mesh racks + (1 Slide drive pinion into position 1 unde … 1 Slide drive pinion into position 1 under drive rack 2 Use M4 adjuster screws to adjust height of rack and M6 to secure 3 Slide out drive pinion and move rack to position 2. Refit drive pinion 4 Use M4 adjuster screws to adjust height of rack and M6 to secure 5 Repeat steps until correct meshing is present at all points indicated to check Do Not glue any of the M4 /M6 socket caps used for adjustment as this will be done at a later stagement as this will be done at a later stage)
TB0452 ZD620 Zebra Printer Setup + (One difference between the GX420d and the … One difference between the GX420d and the ZD620d is the lack of a dedicated power switch. The newer ZD620d opts for a power button that must be pressed in order to turn on the printer after power is supplied. As our machines are fully un-powered after a machine is closed down it causes the operator to intervene and manually turn on the printer after power up. Ideally the Zebra ZD620d has an '''Power Recovery Mode''' that acts as a permanent switch in case of power failure. We can use this on the machines to allow the printer to turn on upon power up. 1. Disconnect from power. 2. Remove module door and use Ethernet cable to remove (plug in and pull). 3. Move the switch that is annotated AUTO to the ON position. 4. Reinstall the module. 5. Reconnect power, this should now turn on. Reconnect power, this should now turn on.)
TB0426 Replacement Zebra Printer Setup + (Open box, unwrap printer, plug in power and plug Ethernet connected to network to the printer. As the printer boots up there will be a red light displayed on the front. After around 30 seconds this will turn green as the printer completes boot up.)
R0015336 Pneumatic Output Testing Part 2 + (Output testing will require valve operatio … Output testing will require valve operation with no e/s circuit Ensure the following Work area is clear from all components not required for testing All colleagues are aware of the procedure being undertaken No additional colleagues are working on the module PCL coupling is accessible to release pressure in case of emergency Testing procedure is fully adhered tocy Testing procedure is fully adhered to)
Training Laser on Ecoline + (Sensitivity also needs settings 5 full turns after turning anticlockwise until it goes Sensitivity then turn clockwise until on then the 5 turns.)
TB0451 CX5120 Beckhoff PC Setup + (Go to Control Panel then ‘Region and Language’ and select ’English (United Kingdom)’.)
Setting Up New Printer - GX420d + (Plug in the power cable and ethernet cable to the back of printer, then turn the printer on with the switch at the back.)