Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

TB0301 Autoflow Saw Head Reinforcement - Additional Enhancements + (On Autoflow 2 Sawing Centres following 5 y … On Autoflow 2 Sawing Centres following 5 years of use., it has been found that the internal saw centre framework can lose its rigidity. this is probably due to "bruising" or denting of the aluminium joints introducing a slight amount of play. This is exacerbated by the design where it is attached and driven on from the base up A retrofit kit of parts has previously been created to allow additional reinforcement to be introduced within the structural framework. This kit builds upon the first kit to provide further accuracy enhancements by #Adding left right stability with additional slide rails at the top of the subframe #Adding front / back stability by moving the SY axis leadscrew to the same height as the saw table ====Parts required: ==== R0010272 Kit: Saw Frame Rigidity Pt 2 This kit consists of 2 carriage assemblies, specifically designed to provide further rigidity to the top of the Saw Head Assembly. In addition, 2 mounting blocks required to relocate the Saw Y Axis Assembly are also included. This allows the Saw Y Axis Assembly to continue to operate accurately, but improves the life of associated components. See also [[TB0259 Autoflow Saw Head Reinforcement]][[TB0259 Autoflow Saw Head Reinforcement]])
Move SR Datum Sensor to Higher Level R0019217 + (On a Mk4 Autoflow, The SR axis daum sensor … On a Mk4 Autoflow, The SR axis daum sensor is originally located at the rear and to the base of the SR axis. This area is prone to offcuts, so a new location has been designed at the top, with the following design parameters *Easy to retrofit *Sensor is protected in a case *Short distance to connection box *Uses existing mounting holes *Easy to adjust and maintain *Sensing end location should be vertical onto a plate, not horizontal on to a radiused surface *Can use E0000336 2mm range sensor reliably *Incorporate a front fence to help deflect offcuts down the chute and to protect the sensor The parts are supplied in Kit R0019217B

...In November 23, a second iteration of the design was released using metal parts and a side fence to improve robustness (R0019217B)

...The pictures and models illustrated here are from a Right to Left feed machine. Parts are unhanded so can be fitted to either hand machine

illustrated here are from a Right to Left feed machine. Parts are unhanded so can be fitted to either hand machine</div> </div> )
ZX5 V Notch Blade Mechanical Setup + (On previous models the V notch separation … On previous models the V notch separation was set via the software. This could be quite time consuming and required multiple tests and measurements to get it right. Four variables were used for each V notch and it is not straight-forward to get the shape, depth and position correct. On the new ZX5 the '''shape''' of the V notch is set mechanically and once set it should never need changed again, but remember that some customers sharpen their V notch blades instead of replacing them. The following was carried out on the rear V notches using some standard outerframe but the process is exactly the same for the front. Once set you can use the usual software settings to increase/decrease depth and to align back to back. The overall process is: # Set the shape of the V notch (Mechanical adjustment) # Set the Depth of the V notch (Software adjustment in Notching Tab) # Set the Position of the V notch (Software adjustment in Notching Tab)

...As you WILL have to stand inside the machining centre I would advise the use of a bump cap and gloves as you will be in close proximity to the V notch blades and tooling.

you will be in close proximity to the V notch blades and tooling.</div> </div>)
Updating Baldor ESB Firmware 2022 + (Since 2022 ABB have removed the simple lin … Since 2022 ABB have removed the simple link from workbench to allow firmware download. This makes it trickier to upgrade an ESB unit on a saw side of a flowline to allow CANopen communication. This is needed on a Windows update. The procedure demonstrates where to find the firmware file and how to download to the ESB manuallyle and how to download to the ESB manually)
ZX5 Transfer Table Setup + (Sometimes the mesh between all the parts i … Sometimes the mesh between all the parts is too tight and left with no adjustment. This causes too much pressure on the moving parts, especially the delrin rollers which are not designed to take heavy loads. Any excess force on them leads to excessive wear and premature failure.s to excessive wear and premature failure.)
Replacing Baldor Microflex Drive with RS Automation + (The Baldor Microflex drive with Beckhoff m … The Baldor Microflex drive with Beckhoff motor was a drive system combination that has now been superseded with a better performance system using an RS Automation Drive and motor combination The Part number for the upgrade is R0019052X Kit: X Axis Replacement using RS Automationit: X Axis Replacement using RS Automation)
Beckhoff AX8000 Flowline Upgrade + (The Flowline range (Mk3, ZX3, ZX4) are Stu … The Flowline range (Mk3, ZX3, ZX4) are Stuga built and designed machines for prepping and cutting uPVC windows and doors. The Flowline is the first machine of the Stuga 'U' shaped machines which has prepping and cutting working in the same machine package. The Flowline is still a fantastic machine for the industry, however, due to the age of the machines and older control systems becoming obsolescent, we have had to find an upgrade route that does not only keep the machine going, but also provides improvements from the original model and up-to-date technology to future proof the machine. The upgrade that we have developed for the Flowline is supplied from an automation supplier named Beckhoff. We also use Beckhoff on our new build machines. This gives us better lead times, more understanding of the products and better diagnostics/ support for our customers. The drive system that we use is called the AX8000 series. These drives are a compact multi axis servo system that use an EtherCAT interface and STO safety functions. These servo drives, coupled with Beckhoff AM8*** series OCT servo motors provide quicker installations and all round performance increases from any system we have previously used. To drive all of the new system, we are using a Beckhoff IPC controller that runs TwinCAT 3. This links into the system via EtherCAT. All of the machine can now link together via EtherCAT to provide quick and stable communications. This tutorial will give you step by step guides on the physical upgrade requirements needed when upgrading a Flowline Mk3 to a Flowline Mk3 with Beckhoff AX8000 Control. Each step will provide you with written information and pictures to guide you through the upgrade. Each step will contain necessary information which will also provide you with rationale for the design and an idea of the benefits over using different methods. Please always feel free to provide Stuga with any feedback on this document or its contents.feedback on this document or its contents.)
GE Control Components Changeover + (The GE control components are now obsolete … The GE control components are now obsolete and we have had to find a new manufacture to use. We have decided to go with Eaton control equipment for this. We are using the same supplier for these products and we have the added benefit if the supplier holding these parts in there stores. We had a choice to use either ABB, Eaton or Schneider components. Although all of the individual Eaton components are a direct replacement for the GE components, there are certain situation that we may be tripped up. This includes times when we need to change a motor breaker that has an auxiliary block connected to it. We can change the breaker but the GE auxiliary block will not fit on the new Eaton one. This means that the Eaton components need to have different part numbers to the GE components. This document will layout the new part numbers and what they relate to and instructions on how they are added and changed in the Sage system. are added and changed in the Sage system.)
ZX5 MH Infeed Basic IO Test and Setup + (The MH infeed on a ZX5 is a module which c … The MH infeed on a ZX5 is a module which can be tested individually away from the fully installed machine. Once build stage is complete, to be able to test individually, the Infeed Module needs: - To be connected to mains power & be powered on - An air supply to the main blue line - Network connection (Network Cube) - HDMI & Keyboard dongle to be plugged into the Beckhoff PLC inside the cabinet. Input and output activation when testing the sole module is done through the Twincat project rather than through WinMulti The above is only required If the Machine is not fully installed and connected with power air and network already. The below guide is specifically for a fully installed and connected infeed.ically for a fully installed and connected infeed.)
PC Recovery Process + (The PCs are now shipped with a memory stick that includes a full recovery image. If the system fails in future, this allows a full recovery of the initial setup of the entire drive. Mouse and Keyboard are required for recovery process.)
ZX5 Adjusting V Notch Depth and Position + (The ZX5 has a twin blade system for the V … The ZX5 has a twin blade system for the V notches that is designed to be easier to set up. The overall process is: # Set the shape of the V notch (Mechanical adjustment) # Set the Depth of the V notch (Software adjustment in Notching Tab) # Set the Position of the V notch (Software adjustment in Notching Tab)otch (Software adjustment in Notching Tab))
TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The ZX5 has two bar measuring systems – th … The ZX5 has two bar measuring systems – the side laser and the sensor array. The side laser scans the bar as it moves into the final loading location, which gives the software a “heads-up” for the length of the bar. If the length is different to expected, the software will then use the sensor array to measure the bar length. There are 2 measurement methods because the side laser is not 100% reliable, especially on shorter lengths below 3000mm. However, it does mean the system does not have to grip and measure / reoptimize each bar length, so improves the cycle time. The sequence is as follows 1. During the conveyor loading, measure the length using the side laser 2. Once loaded to backfence, check the backfence sensor array. 3. If the sensor array rough measurement does not match the laser – a. If the laser measured length < infeedLaserRemeasure, continue and measure with rear sensors b. If the laser measured length < infeedLaserRemeasure, flag an error that laser has not measured correctly. c. If it does match, use the laser value to reoptimize the bar if it is different than expected 4. Load and Grip bar, if necessary, measure accurately with rear sensor arrayssary, measure accurately with rear sensor array)
ZX5 Alignment Check + (The ZX5 machine can be tricky to align as there are many adjustments designed into the table to offset manufacturing tolerances. This step by step guide follows the correct protocol to ensure the starting point and sequence of alignment is correct)
Repairing R axis datum pin + (The datum pin on the old ZX4 at Sidey was … The datum pin on the old ZX4 at Sidey was recommended to be changed at my last service visit. Unfortunately there are quite a few different datum spindle plates and we were having problems tracking down the correct one so it was decided that I would be sent out the new replaceable datum pin carrier as Sidey have a small machine shop I could use to modify the existing plate to make it fit. Unfortunately the mounting holes of the new carrier interfered with the mounting holes of the pneumatic cylinder so it couldn't be used. After taking dimensions of the existing plate for identification I realised there was actually a very small and quick repair that could be carried out until the correct parts were identified. All you need is a cordless drill, a 2.5 and a 3.1mm drill, M3 tap and an M3 x 15mm cap head screw.l, M3 tap and an M3 x 15mm cap head screw.)
ZX5 Gripper Energy Chain & Tray Setup + (<div class="icon-instructions caution-i …

...August 2023 - The energy chain and method used in this dokit has been superseded by https://stuga.dokit.app/wiki/Energy_Chain_Installation_-_2500_Series

The main problems we’ve had during commissioning with these energy chains is that if they are not positioned well enough , the chain will clip the button heads that hold the trays to the L brackets To get over this the brackets sometimes need adjusting on the slots along with possibly bending into a better shape or by adjusting the chain bracket position on the slots in the ‘finger’ bracket Things to look out for: *There should be three links which are reversed at the bracket end of the energy chain. *Servo cable and the pipes and cables from the energy chain are fixed with cable ties to the fingers on the bracket to minimise possible movement and twisting which changes where the energy chain sits in the trays, meaning it could start clipping the button heads. *Tray heights and energy chain length, there should be a consistent gap all the way along between the energy chain and the top tray (viewed from inside the tray) and when at the full travel either end the chain shouldn’t be tight hitting the fence too much at the end. *It is also worth checking if all of the links fitted are the same radius type, as we have had occasions where some have been a smaller radius meaning at certain points down the rack the radius of the bend becomes smaller and falls out from the support of the top tray, especially when the gripper is at either end of the rack. There is a code on the side of each link in the energy chain. *A last thing to be weary of is is the end corners of the trays may require bending out, there have been occasions where one chain tray has been slightly more bent in than the other meaning when the chain moves from one tray to the next it clips the corner of the next tray We normally get the gripper on a reversing cycle movement to test this through the twincat project at different speeds, starting slow and working up to higher speeds.gh the twincat project at different speeds, starting slow and working up to higher speeds.)
X252 Forward Clamp Out Sensor Setup Stuertz Infeed + (The out sensor used for the vorlaufwagen c … The out sensor used for the vorlaufwagen cannot be a standard reed switch because the cylinder that drives this output is a telescoping version. It is impossible to detect the out position. Therefore, a sensor is fitted that must be programmed to set a high output when it detects the full range has been reached The sensor is a [https://www.pepperl-fuchs.com/global/en/classid_53.htm?view=productdetails&prodid=42559#overview Pepperl+Fuchs VDM28-8-L] Datasheet can be downloaded [https://files.pepperl-fuchs.com/webcat/navi/productInfo/45/452859n.pdf?v=20220926110229 here] '''Function''' The distance measurement device contains one transmitter and one receiver incorporated into a single housing. The transmitter light is reflected back to the receiver from a target. The sensor determines the distance to the target and triggers a switching function or supplies the relevant measured value for processing. '''Assembly instructions''' The sensor can be mounted by means of through holes or by using a mounting bracket or mounting clamp Ensure that the surface is level in order to prevent the housing from becoming distorted when the fittings are tightened. It is advisable to secure the nuts and screws using spring washers in order to prevent the sensor from being incorrectly adjusted. '''Connection''' Connect the device in accordance with the connection diagram in the datasheet. '''Adjustment''' The green LED lights up when the operating voltage is switched on. Adjust the sensor so that the laser point is on the gripper bodyso that the laser point is on the gripper body)
Stuertz Infeed - Align and dowel GX rack + (The rack on a Stuertz infeed is a helical … The rack on a Stuertz infeed is a helical type and is supplied unpinned, as the motor is not connected before delivery to Stuga The alignment must be checked then dowelled with 5mm roll pins The racks are already located in the "Y" direction with location pins, this procedure is purely to align the racks to each other in the GX directionhe racks to each other in the GX direction)
Alignment guide using wire line + (This dokit is to help with the use of a wi … This dokit is to help with the use of a wire line to set alignment correctly on mechanical build up. Using a wire line correctly will ensure a very accurate straight line is achieved . Accuracy of + - 1 mm over any distance can be achieved using the following method. Using one incorrectly can also easily be done.! The steps shown can be applied to all types of alignment , when you have a vertical face on components that require aligning. face on components that require aligning.)
Ecoline - Setting V Notches on winMulti Software + (This is the full setup procedure for V not … This is the full setup procedure for V notches on an Ecoline. This should only be needed on initial commissioning or if the shape of the notch has changed due to some physical intervention, for example - - Blade Change - Blade buckled

...If there is no direct reason to change the blade shape or position, there is a different root cause to the problem that changing parameters WILL NOT SOLVE

...If the results of your tests do not make sense, or the position seems to vary by the wrong amount or wrong direction after making a change, then a serious mechanical problem exists elsewhere. There is no sense carrying on because you cannot complete this setup unless the machine is consistent and reliable

here is no sense carrying on because you cannot complete this setup unless the machine is consistent and reliable</div> </div> )
Importing Picking List from Sage To Monday + (This procedure demonstrates how to use the … This procedure demonstrates how to use the "Sage Hooks" MS Access database to grab the data created in Sage and exort to a spreadsheet. The spreadsheet is then imported into a new Monday board, then copied across to the correct Picking List for the machine build.
Picking List for the machine build. )
Flowline 6 to 6o5m Extension + (This procedure describes how to upgrade a … This procedure describes how to upgrade a flowline to increase the standard capacity from 6.0m to 6.5m. The procedure involves extending the machining centre outfeed travel and saw infeed travel base to 6.0m to cope with a longer rail on each side. These are generally supplied as a new part. Other ancillary parts that will need extending * Cables * Energy Chainsl need extending * Cables * Energy Chains)
ACEpc Installing netedit with NetSetGo disk + (This procedure will completely overwrite a … This procedure will completely overwrite any data on the hard drive of the ACEpc. This is not a problem on a flowline where the data resides on the main MH hard drive in a shared directory c:\saw. If this process is to be carried out on a standalone saw or router, make sure the data is backed up first.
e sure the data is backed up first. )
Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
Fitting Zx5 Crank Upgrade + (This upgrade replaces the crank arm assemb … This upgrade replaces the crank arm assemblies on Z065, Z066 and Z067 with a direct drive system to improve reliability This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes

...The drives must be programmed before parts sent out

...Motors must be rewired for Delta and NOT Star

></div> <div class="icon-instructions-text">...Motors must be rewired for Delta and NOT Star</div> </div> )
R0019207 Upgrade SR Axis Spigot + (This upgrade utilises upgraded parts to en … This upgrade utilises upgraded parts to ensure a mechanical fix is maintained between the SR axis gearbox and main drive pin , whilst also giving the ability once upgraded for the gearbox to be removed with minimal mechanical time. three main parts will be replaced in this upgrade, obsoleting the removed parts Main components of upgrade D00004019E Turntable Mk5 D0004033E Alignment disc Mk5 D0004147E Turntable shaft Mk5nt disc Mk5 D0004147E Turntable shaft Mk5)
B0000082b Motor replacement For Obsolete part B0000082 + (To rectify the obsoletion of B0000082 driv … To rectify the obsoletion of B0000082 drive motor, the following replacement kit has been designed to enable continued support of older assemblies within stuga machines . The kit consists of a new motor and appropriate gearbox, adapter plate and new fasteners . Also details are included here for a small modification to enable the upgrade to function correctly Following parts are required for this upgrade B0000082b load motor and gearbox 1 off D0008225b adapter plate F0000189 M6 x 25 set bolts 4 off F0000058 A form washer 4 off F0000190 M8 x 40 set bolts 2 off F0000007 M5 x 16 cap head bolt 4 off off F0000007 M5 x 16 cap head bolt 4 off)
Upgrade Autoflow to Windows 10 + (Update 2024 - Upgrades now consist of a ne … Update 2024 - Upgrades now consist of a new Windows 11 PC with VM for the front end and a C6017 PC for the back end. Upgrading an Autoflow to Windows 10 involves upgrading two PCS #The Beckhoff control PC - replaced with a C0001225-KIT #The Camera PC - replaced with a C0000422-KIT with a VM setup. this now becomes the front end PC
=== For Historical reference, these are the pre-2024 notes: === ''Upgrading an Autoflow to Windows 10 on site involves upgrading two PCS'' #''The Beckhoff control PC'' #''The Camera PC'' ''
The Beckhoff PC is not upgradable so needs to be completely replaced. We use the miniature [https://www.beckhoff.com/english.asp?industrial_pc/c6017.htm Beckhoff C6017] for this'' ''It is not cost effective to upgrade and old camera PC, so a new one is supplied'' ===''Notes''=== *''The Beckhoff PC is now powerful enough to run the front end and back end.'' *''The camera PC is there to replace the camera PC on site and contains the storage for the machine cameras'' *''Because the Beckhoff PC has limited hard drive space, the DDRIVE will be on the cameraPC''hard drive space, the DDRIVE will be on the cameraPC'')
Ecoline - Datum and MitreOffset Tests + (When an Ecoline is commissioned, the posit … When an Ecoline is commissioned, the positional accuracy needs to be set up. These are also useful tests to check if the machine is maintaining positional accuracy

...ALWAYS make sure you have consistent, repeatable results before making any parameter changes

tent, repeatable results before making any parameter changes</div> </div> )
PLC Source Control - Git Credential Manager for Windows Install + (When connecting to the tc3Multi repository … When connecting to the tc3Multi repository on BitBucket.org, some times the validation credentials are not accepted. Check that the password you have is correct, if the problem persists , install or update Git Credential manager for windows to the latest version.manager for windows to the latest version.)

ZX5 - ZX3 Hepco alignment Module E Saw Infeed + (Alignment and check procedure for mounting … Alignment and check procedure for mounting of hepco rail To main frame Parts required B0001102 hepco rail D0015492 5 off vertical adjustment plate D0015493 5 off Lateral adjustment plate D0015072 1 off Carriage Plate B0000184 journal wiper 4 off B0000185 journal 2 off B0000186 journal 2off Hepco Levelling Jig Hepco rail v block jigs Hepco rail Drive rack pitching jigk jigs Hepco rail Drive rack pitching jig)

Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3 + (<div class="annotatedImageDiv" typeof=" …
Autoflows from A2001 to A2015 were initially produced with TwinCAT2 software. This has now been superseded with TwinCAT3 which then has the benefit of compatibility with version 6 front end software.

The original PC cannot be used because

*It is not powerful enough to run v6 front end
*The operating system cannot be upgraded to Windows 10
*It cannot be upgraded to TwinCAT3

The Beckhoff C6015 PC has been chosen to be the replacement PC. It is compact, yet powerful enough to run the v6 front end and TwinCAT in the same
. It has an upgrade to 1.9Ghz 4 core processor.

Because it has a limited 40Gb SSD memory, a compact 64Gb memory stick is inserted into the USB 3.0 port. This acts as a separate drive for the DDRIVE dynamic storage for all machine setup. The internat drive is for the Operating System only. This mimics the current Autoflow setup of a remote Camera PC, hence the camera PC can be retired after the upgrade
era PC, hence the camera PC can be retired after the upgrade )
R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (<nowiki>'''Tools required&l … '''Tools required'''

Tape rule

Steel rule

standard hex keys

Standard HSS drill set

Standard Tap set

Hack saw

Ball Pein hammer

Centre punch

'''Part Required'''

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 3

P0000024 Fitting: Hex Nipple 1/4 BSP x 1

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000097 Fitting: Elbow Adaptor 8mm - 1/4 BSPT x 1

P0000159 Fitting: Stem Blanking Plug 6mm x 3

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000279 Female Cross 1/4'' NPT x 1

P0000297 HighLow Pressure Valve x 1

P0000419 Air Service Unit OH (P0283)x 1

P0001070 Valve Base: Type 41 6 Position Ø6 x 2

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8

P0001101 Male straight 12mm to 1/4 bsp x 5

P0001102 Male elbow 12mm to 1/4 x 2

P0001186 Valve 24v dc SMC x 12

;P0001070 Valve Base: Type 41 6 Position Ø6 x 2 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8 P0001101 Male straight 12mm to 1/4 bsp x 5 P0001102 Male elbow 12mm to 1/4 x 2 P0001186 Valve 24v dc SMC x 12 </nowiki>)
R0015316 V notch Final Assembly + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex key set

Standard Spanner set

ZX5 Blade tightening tool

Compressed air connection with regulation (for axis support)

'''Parts required'''

A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2

A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2

B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4

B0000173 Blanking plug foc x 28

B0000426 Linear Rail MSB25 400mm Long (AMT) x 4

D0015156 Saw Bearing Plate x 2

D0015161 Saw Plate x 4

D0015162 Saw Mid Spacer Bar x 1

D0015163 Saw Bearing Spacer Bar x 1

D0015168B Balance Cylinder Bracket x 2

D0015169B Cylinder Rod Bracket x 2

D0015179 Energy Chain Bracket x 2

D0015180 Datum Switch Bracket (VZ) x 1

D0015183 VY Stop x 2

D0015235 VY Datum Switch Bracket x 1

D0015236 VY Energy Chain Bracket - Fixed x 1

D0015237 VY Energy Chain Bracket - Moving x 1

D0015250 Safe Sensor Block x 1

D0015251 Safe Sensor Finger x 1

D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2

D0015452 Scissor Cable Retainer x 1

D0015541 Energy Chain Deflector x 1

D0015704 Energy Chain Support Plate x 1

E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2

E0001185 Elte Saw motor x 4

M0001087 Rubber Bump Stop M6 Ø20x24 x2

P0000010 1/8 6mm elbow x 1

P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1

P0000023 Fitting: Hex Nipple 1/8 BSP x 1

P0000026 Silencer 1/4 BSP x 1

P0000050 Fitting: Silencer 1/8'' BSP x 1

P0000077 Straight Adaptor 8mm - 1/8BSP x 1

P0000140 Fitting: Quick Exhaust Valve 1/8" x 1

P0001040 Fitting: 1/8BSP Hex Head Silencer x 2

P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2

P0001133 Cylinder: Ø50 x 500 x 2

P0001134 Floating Joint M18x1.5 x 2

P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2

P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1

P0001142 Adjustable Damper 150mm stroke (3000N) x 1

P0001144 Reed Switch Mounting Band for Ø50 cyl x 2

R0015084 Bench assemble and Drill Off Swarf chutes

V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4

BJ3-1 x 2 P0001133 Cylinder: Ø50 x 500 x 2 P0001134 Floating Joint M18x1.5 x 2 P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2 P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1 P0001142 Adjustable Damper 150mm stroke (3000N) x 1 P0001144 Reed Switch Mounting Band for Ø50 cyl x 2 R0015084 Bench assemble and Drill Off Swarf chutes V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 </nowiki>)
R0015114 Bench Assemble Valve Banks and Regulators + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard hex key set

Standard spanner set

Standard HSS drill set

Standard tap set

'''Parts Required'''

H0007998 Regulator internal mount 5 way x 1

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14

P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9

P0000021 air gun assembly x 1

P0000024 hex nipple 1/4 x 3

P0000058 Regulator Mounting Kit x 1

P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2

P0000145 tee equal 1/4 x 3

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1

P0000278 Regulator 0-2 bar x 1

P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8

P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1

P0000419 Air Service Unit OH (P0283) x 1

P0001071 Valve base type41 8 position x 1

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4

P0001101 Male straight 1/4 bsp to 12mm x 2

P0001102 Fitting male elbow 12mm 1/4 x 4

P0001105 Bulkhead straight 12mm x 6

P0001186 Valve. 24v dc smc x 8

 P0001071 Valve base type41 8 position x 1 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4 P0001101 Male straight 1/4 bsp to 12mm x 2 P0001102 Fitting male elbow 12mm 1/4 x 4 P0001105 Bulkhead straight 12mm x 6 P0001186 Valve. 24v dc smc x 8 </nowiki>)
R0015342 Bench Assemble Outfeed Parts + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex Key set

Standard spanner set

Standard screwdriver set

Bearing press

Test box for cylinder switch function

'''Parts Required'''

B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8

B0000236 90 Deg Grease Nipple M6 ST/ST x 4

D0004311 Side Eject Block x 2

D0004591 Side Eject Housing x 2

D0004592 Eject Housing Plate x 2

D0005200 Safety Dead Stop Block x 1

D0005201 Safety Dead Stop Backer (5357) x 1

D0005202 Safety Dead stop Yoke (5358) x 1

D0005203 Safety Slider Cap x 2

H0004626 Shaft 16mm: 275 Eject Push x 4

M0000101 Compression Spring 11 D 15 D 25 Long x 1

P0000035 Cylinder 25x160 x 2

P0000174 Fitting: Plug 1/4'' BSP (Grubscrew Type x 2

P0000201 Flow Controller 6mm x M5 Elbow x 2

P0000367 16mm bore X 125 stroke with rod end clevis x 1

P0000369 Clamp to suit P0000367 x 2

P0000444 Reed Switch: Pneumax 1580U (5.0m Lead) x 2

P0001068 Valve Base: Type 41 2 Position Ø6 x 1

P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1

P0001163 1/4 bsp male silencer x 2

P0001186 Valve/ 5/2 smc x 2

P0001198 1/8 bsp 6mm speed controller x 4

P0000394 reed switch holder x 2

P0000-444 Reed switch pneumax x 2t; P0001068 Valve Base: Type 41 2 Position Ø6 x 1 P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1 P0001163 1/4 bsp male silencer x 2 P0001186 Valve/ 5/2 smc x 2 P0001198 1/8 bsp 6mm speed controller x 4 P0000394 reed switch holder x 2 P0000-444 Reed switch pneumax x 2</nowiki>)
R0015316 V notch Final Assembly Part 2 + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex key set

Standard Spanner set

ZX5 Blade tightening tool

Compressed air connection with regulation (for axis support)

'''Parts required'''

A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2

A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2

B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4

B0000173 Blanking plug foc x 28

B0000426 Linear Rail MSB25 400mm Long (AMT) x 4

D0015156 Saw Bearing Plate x 2

D0015161 Saw Plate x 4

D0015162 Saw Mid Spacer Bar x 1

D0015163 Saw Bearing Spacer Bar x 1

D0015168B Balance Cylinder Bracket x 2

D0015169B Cylinder Rod Bracket x 2

D0015179 Energy Chain Bracket x 2

D0015180 Datum Switch Bracket (VZ) x 1

D0015183 VY Stop x 2

D0015235 VY Datum Switch Bracket x 1

D0015236 VY Energy Chain Bracket - Fixed x 1

D0015237 VY Energy Chain Bracket - Moving x 1

D0015250 Safe Sensor Block x 1

D0015251 Safe Sensor Finger x 1

D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2

D0015452 Scissor Cable Retainer x 1

D0015541 Energy Chain Deflector x 1

D0015704 Energy Chain Support Plate x 1

E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2

E0001185 Elte Saw motor x 4

M0001087 Rubber Bump Stop M6 Ø20x24 x2

P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1

P0000023 Fitting: Hex Nipple 1/8 BSP x 1

P0000026 Silencer 1/4 BSP x 1

P0000050 Fitting: Silencer 1/8'' BSP x 1

P0000077 Straight Adaptor 8mm - 1/8BSP x 1

P0000140 Fitting: Quick Exhaust Valve 1/8" x 1

P0001040 Fitting: 1/8BSP Hex Head Silencer x 2

P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2

P0001133 Cylinder: Ø50 x 500 x 2

P0001134 Floating Joint M18x1.5 x 2

P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2

P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1

P0001142 Adjustable Damper 150mm stroke (3000N) x 1

P0001144 Reed Switch Mounting Band for Ø50 cyl x 2

R0015084 Bench assemble and Drill Off Swarf chutes

V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 BJ3-1 x 2 P0001133 Cylinder: Ø50 x 500 x 2 P0001134 Floating Joint M18x1.5 x 2 P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2 P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1 P0001142 Adjustable Damper 150mm stroke (3000N) x 1 P0001144 Reed Switch Mounting Band for Ø50 cyl x 2 R0015084 Bench assemble and Drill Off Swarf chutes V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4</nowiki>)
R0000963E Bench Assemble Z axis Components + (<nowiki>'''Tools Required'' … '''Tools Required'''

Standard hex key set

Standard spanner set

Emery tape

Standard HSS drill set

Hand reamer

Standard tap set

'''Part Required'''

B0000086 Ball Bearing 15 D 32 D 9 Long + seals x 4

B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals x 2

B0000351 Bearing 40mm O/D 17mm I/D 17.5mm Wide x 2

C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1

D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1

D0006501 Z Leadscrew Sleeve x 2

D0007629 Cylinder rod Extension x 4

D0007732 Sprocket Idler Shaft x 2

D0007733 Sprocket Mounting Block x 2

D0008090 Retaining Collar x 1

H0007715 Z Sprocket 33 Teeth 3/8'' pitch x 2

H0007790 Leadscrew Z(Includes Re-balling) x 2

P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 2

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 2

P0000023 Fitting: Hex Nipple 1/8 BSP x 2

P0000024 Fitting: Hex Nipple 1/4 BSP x 2

P0000026 Silencer 1/4 BSP x 4

P0000051 Fitting: Straight Adaptor 6mm - 1/4 BSPT x 4

P0000140 Fitting: Quick Exhaust Valve 1/8" x 2

P0000145 Tee-Equal 1/4BSP Galvanised x 2

P0000200 Elbow Adaptor 6mm - M5 x 2

P0000229 Pneumax VDMA 40 x 300 Magnetic x 4

P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4

P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2

t; P0000140 Fitting: Quick Exhaust Valve 1/8" x 2 P0000145 Tee-Equal 1/4BSP Galvanised x 2 P0000200 Elbow Adaptor 6mm - M5 x 2 P0000229 Pneumax VDMA 40 x 300 Magnetic x 4 P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4 P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2 </nowiki>)
R0015028D ZX5 Hepco Beam Alignment Module C + ('''Tools Required''' … '''Tools Required''' Engineers level Hepco flat spanner T0000491 Hepco Box spanner T0000492 Standard hex key set Incremental shim pack '''Parts Required''' B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 6 B0000184 Journal Cap Seal 34 x 4 B0000185 Double Row Long Stud Journal Eccentric x 2 B0000186 Double Row Long Stud Journal Concentric x 2 B0000234 Straight Grease Nipple M6 ST/ST x 6 B0001006 Linear rail 25mm x 820mm x 6 B0001102 Double edge spacer slide and beam 7600mm x 1 D0015072 Carriage Plate x 1 D0015492 Vertical Beam Adjustment Plate x 5 D0015493 Lateral Beam Adjustment Plate x 5 P0000200 Elbow Adaptor 6mm - M5 x 2 B0000173 blanking cap x 90 F0000331 M6 threaded plate x 120 x 2 B0000173 blanking cap x 90 F0000331 M6 threaded plate x 120)
R0015028D ZX5 Hepco Beam Alignment Module C part 2 + ('''Tools Required''' … '''Tools Required''' Engineers level Hepco flat spanner T0000491 Hepco Box spanner T0000492 Standard hex key set Incremental shim pack '''Parts Required''' B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 6 B0000184 Journal Cap Seal 34 x 4 B0000185 Double Row Long Stud Journal Eccentric x 2 B0000186 Double Row Long Stud Journal Concentric x 2 B0000234 Straight Grease Nipple M6 ST/ST x 6 B0001006 Linear rail 25mm x 820mm x 6 B0001102 Double edge spacer slide and beam 7600mm x 1 D0015072 Carriage Plate x 1 D0015492 Vertical Beam Adjustment Plate x 5 D0015493 Lateral Beam Adjustment Plate x 5 P0000200 Elbow Adaptor 6mm - M5 x 2 B0000173 blanking cap x 90 F0000331 M6 threaded plate x 120 x 2 B0000173 blanking cap x 90 F0000331 M6 threaded plate x 120)
R0015296 Bench Assemble Bearing Assemblies + ('''Tools Required''' … '''Tools Required''' Heat Gun Standard Hex key set Fe10 solvent '''Parts Required''' B0000109 Linear Bearing (IKO) 40 D x 62 D x 80 L x 8 D0003236 Nut Block (25 x 10 pitch) x 1 D0006003 Horizontal Linear Block x 3 D0006023 Vertical Linear Block x 4
ontal Linear Block x 3 D0006023 Vertical Linear Block x 4 )
R0015071 Bench Assemble Pneumatics Rail + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Pipe cutters Standard HSS drill set Step cutting drill Standard screwdriver set '''Parts Required''' D0010167 x 3 C0001018 x 3 D0016300 x 1 P0001139 x 1 P0001102 x 2 P0001032 x 2 P0001068 x 1 P0001101 x 3 P0001163 x 8 P0001071 x 1 P0001186 x 10 P0001151 x 1 A0000240 x 1 P0000159 x 501071 x 1 P0001186 x 10 P0001151 x 1 A0000240 x 1 P0000159 x 5)
R0015266B mount completed assemblies + ('''Tools Required''' … '''Tools Required''' Standard hex key set '''Parts Required''' D0015432 Spacer: Ø25.4 x 100mm (12.7mm ID) x 10 D0015479 Sensor Mount Rail 1450 mm Long x 4 D0015480 Sensor Mount Rail 825 Long x 1 F0000299 T Nut Sub Insert M6 (Fat) x 16 R0015074 Pre assembled keyboard mount and buttons R0015030B Bench Assembly Loader Wheel R0015080 Bench assemble sensor rail R0015271 Mount buffer bars ( pre fitted to frame ) R0015351 Mount monitor to frame (pre fitted to frame) to frame ) R0015351 Mount monitor to frame (pre fitted to frame))
R0015082B fencing and guards + ('''Tools Required''' … '''Tools Required''' Standard hex key set standard spanner set Standard HSS drill set Standard Tap set 1 meter level Tape measure Steel rule '''Parts Required''' D0008330 Double Door Keep x 2 D0015326 Transfer Gate Upright x 6 D0015333 ZX5 Fence Hinge Spacer x 6 D0015340 Profile Support Plate (Short) x 1 D0015341 Profile support plate mount x 1 D0015349 Safety Hinge Mounting Plate x 6 D0015517 Fence Mounting Section x 28 D0015526 ZX5 Saw Fence Infill x 1 D0015601 ZX5 Saw Fence Support Beam (40x80x550) x 1 D0015606 Fence 10 Support Beam F Slot Fixings. x 2 D0015771 Double Door Keep Spacer x 1 D0015914 Saw Infeed Profile Deflector x 1 D0015962 ZX5 Fence 11 - 1100 x 1850 x 2 D0015963 ZX5 Fence 1 1450 x 1850 x 12 D0015964 ZX5 Fence 3 - 1450 x 1850 Cutout x 1 D0015965 ZX5 Fence 2 820 x 1850 x 1 D0015966 ZX5 Fence 10 927 x 1850 x 2 D0015967 ZX5 Transfer Gate x 3 D0015968 ZX5 Fence 7 642x 1850 extraction holes x 1 D0015969 ZX5 Fence 8 - 1105 x 105 Saw Corner x 1 D0015970 ZX5 Fence 820 x 1105 x 1 D0015972 ZX5 Fence Infill - 65 x 1850 x 1 D0015974 ZX5 Fence 13 - 820 x 1105 Hole for Gate x 1 D0015986 Multi Head Waste Bin Guard x 2 D0016018 ZX5 Saw Cabinet Infill Guard x 1 D0016036 Compliance Guard around Cabinet x 1 D0016037 Compliance Guard - MH to MH Infeed x 1 D0016038 Compliance Guard - MH to MH Out x 1 D0016051 Fence Guard (Crank) x 4 D0016171 Compliance Guard - MH to Transfer Gate x 1 D0016172 Compliance Guard - Saw to Transfer Gate x 1 E0001176 Safety Hinge Switch x 3 E0001177 Hinge (works with E1176 Safety Switch) x 3 F0000299 T Nut Sub Insert M6 (Fat) x 83 M0000029 Cabinet Lock (Triangular) x 4 M0000515 Floor Mouting Angle 200x87x42x 7 M0000516 Adjustable Foot Ø60 M14 x 6 M0001016 Angle 74 x 38 x 6 M0001202 Bruehl Fence Panel 1825 x 2200 x 4 M0001204 Bruehl 2.0m Transit Post x 5 M0001207 Bruehl Fence Clip x 31 R0000901 ZX4 Local Gate x 1
01207 Bruehl Fence Clip x 31 R0000901 ZX4 Local Gate x 1 )
R0015288 Bench Assemble Transfer slider units and Cylinder Rails + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set '''Parts Required''' B0001160 Delrin Dual V Wheel Kit x 48 B0001161 Spacer: Concentric - Delrin Dual V Wheel x 24 B0001162 Spacer: Eccentric - Delrin Dual V Wheel x 24 D0015255 Rack: Mod2 360 Long x 8 D0015551 Rack Mounting Plate x 8 D0015572 Slideway Connection Plate (2018) x 8 D0015573 Transfer Cylinder Bracket x 8 D0015576 Pneumatics Support Spacer x 8 D0015599 Transfer Cylinder Bracket Brace x 8 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 48 P0001111 Cylinder: Ø25 x 25S Cut Shaft x 48 R0015093 Bench Assemble Transfer Beam x 8
S Cut Shaft x 48 R0015093 Bench Assemble Transfer Beam x 8 )
R0000088E Stage 1 Spindle assemble + ('''Tools Required''' … '''Tools Required''' Standard hex key set 5mm hex drill bit Drill Driver Ball pien hammer Nylon block 0.05 Feeler gauge '''Parts Required''' B0000045 linear rail x 8 B0000044 linear railx 4 B0000173 blanking caps x 68 B0000046 bearing x 24 D0007816 nipple extension x 12 B0000233 grease nipple metric fine x 24 D0007724 double slide base x 4 D0007725 single slide base x 4
07724 double slide base x 4 D0007725 single slide base x 4 )
R0015063 Bench Assemble Roller Tables + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Tape measure/Rule 8.2mm HSS drill Drill '''Parts Required''' B0001092 Plastic roller x 48 B0001103 Bush flange x 28 B0001220 Spacer x 28 D0015001 Roller Bed Cylinder Arm x14 D0015002 Shaft 10mm: 58mm Rod End x 14 D0015003 Roller Bed Rail 375mm x 6 D0015004 Roller Bed Rail 550mm x 2 D0015005 Roller Bed Rail 1000mm x 10 D0015006B Roller Bed Arm Bracket x 14 D0015010 Rod End Spacer x 28 D0015283 Saw Infeed Backfence Plate x 5 D0015481 Shaft 8mm: 50mm Cylinder Pivot x 14 D0015547 Sensor Blower Plate x 1 D0015603 Roller Bed Pivot Shaft (silver steel) x 14 D0015608 Saw Infeed Backfence Plate (Full Length) x 5 E0001120 Sensor: Ultrasonic M8 20-150mm x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 14 P0000200 Elbow Adaptor 6mm - M5 x 1 P0001152 Cylinder 25 x 25 x 14 P0001198 Fitting Speed controller 1/8 x 6mm tube x 28 P0000160 flow regulator x1
ontroller 1/8 x 6mm tube x 28 P0000160 flow regulator x1 )
R0000558E Bench Assemble Base and Turntable + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1
ainless lock washer x 4 D0015663 SR Axis Motor Guard x 1 )
R0015329 Fit Head Spindle Posts + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard flat hand file Emery tape 120 standard hand tap set Stubby hex key set Ratchet/hex bit set Blade flange spanner '''Parts Required''' D0004002 Webb x 1 D0004003 Top Shaft Block x 2 D0004004 Brace Support Bar (D7451) x 1 D0004157 Motor plate spacer x 3 D0004342 Damper Bracket (5312) x 1 D0007451 Brace Support Bar OH (D4004) x 1 D0015490 Saw Turntable Sensor Flag x 1 D0015491 Saw Turntable Flag Bracket x 1 H0004024 Infeed Clamp Post x 1 H0004025 Outfeed Clamp Post (5302) x 1 H0004510 Shaft 30mm: 540 Saw Stroke x 2 P0000055 Adjustable Damper 200mm (Saw Stroke) x 1 R0000560 Bench Assemble Spindle x 1 R0000569E Bench Assemble Head Spindle Posts Mk5 x 1 V0000043B Saw Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1
Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1 )
R0015285 Bench Assemble Pneumatic Rail + ('''Tools Required''' … '''Tools Required''' Standard spanner set Standard hex key set Pipe cutters Standard screwdriver set '''Parts Required''' D0016300 x 1 P0001074 x 8 P0001101 x 2 P0001102 x 2 P0001071 x 1 P0001186 x 10 P0001068 x 1 P0000470 x 1 P0001040 x 2 P0000010 x 6 P00000007 x 2 P0000142 x 1 P0001008 x 2 D0010167 x 2 C0001018 x 2 P0001022 x 2 P0001009 x 2 P0001108 x 4 P0001166 x 1 P0001106 x 1
x 2 P0001009 x 2 P0001108 x 4 P0001166 x 1 P0001106 x 1 )
R0015081 Bench Assemble Single Roller Table + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set '''Parts Required''' B0001103 Bush Flange 8 I/D 10 O/D 3.8 Long iglidur J type x 2 B0001154 Plastic Roller Blue Ø30 x 160 Long. Spring Loaded Shafts x 4 B0001168 Bush Sleeve 8 I/D 10 O/D 8L iglidur J type x 2 D0015001 Roller Bed Cylinder Arm x 1 D0015002 Shaft 10mm: 58mm Rod End x 1 D0015006B Roller Bed Arm Bracket x 1 D0015481 Shaft 8mm: 50mm Cylinder Pivot x 1 D0015483 Infeed Loader Roller Bed Mount x 1 D0015594 Roller Bed Rail (Loader Wheel) x 2 D0015603 Roller Bed Pivot Shaft (silver steel) x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 2 P0001110 Cylinder 25 x 10 x 2 P0001198 Air Fitting x 4 x 2 P0001110 Cylinder 25 x 10 x 2 P0001198 Air Fitting x 4)
R0015007 Bench Assemble Roller Tables Machining Outfeed + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Tape measure/Rule 8.2mm HSS drill Drill '''Parts Required''' B0001092 Plastic Roller Blue Ø30 x 194 Long. Spring Loaded Shafts x 45 B0001103 bush flange x 26 B0001220 spacer x 26 D0015001 Roller Bed Cylinder Arm x 13 D0015002 Shaft 10mm: 58mm Rod End x 13 D0015003 Roller Bed Rail 375mm x 4 D0015004 Roller Bed Rail 550mm x 2 D0015005 Roller Bed Rail 1000mm x 10 D0015006B Roller Bed Arm Bracket x 13 D0015010 Rod End Spacer x 26 D0015481 Shaft 8mm: 50mm Cylinder Pivot x 13 D0015547 Sensor Blower Plate x 2 D0015603 Roller Bed Pivot Shaft (silver steel) x 13 E0001120 Sensor: Ultrasonic M8 20-150mm x 2 P0000046 Fitting: 'Y' Adaptor 6mm x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 13 P0000200 Elbow Adaptor 6mm - M5 x 2 P0001030 Fitting: SMC 6mm Equal Tee x 10 P0001110 cylinder 25 x 10 x 13 P0001198 Fitting flow reg x 26
01110 cylinder 25 x 10 x 13 P0001198 Fitting flow reg x 26 )
R0015278 Mount Completed Assemblies Section two + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chainsembly R0015286 Bench Assemble X axis components and energy chain)
R0000570B Bench Assemble 1st stage Ejector + ('''Tools Required''' … '''Tools Required''' Standard hex key set '''Parts Required''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 6 D0004015 Front Slider (5301) x 1 D0004016 Rear Slider x 1 D0004329 Rod End Plate (5304) x 1 D0004420 Extension Linear Block x 2 H0004630 Shaft 20mm: 345 Ejector Crossx 1
Linear Block x 2 H0004630 Shaft 20mm: 345 Ejector Crossx 1 )
R0015352 Mount Buffer Beams + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set 1 meter spirit level Tape measure '''Parts Required''' D0015326 transfer gate upright x 4 D0015334 ZX fence corner post x 2 D0015607 Fence 11 support beam x 4 D0015335 ZX fence cross post x 4 D0010202 Frame joining plate x 2 D0015232 Fence mounting bracket x 2 M0001016 angle bracket x 2 M0000516 adjustable foot x 2
0001016 angle bracket x 2 M0000516 adjustable foot x 2 )
R0015278 Mount Completed Assemblies + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 1 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chain
R0015286 Bench Assemble X axis components and energy chain )
R0000713E Bench Assemble R Axis Limit Assembly + ('''Tools Required''' … '''Tools Required''' Standard hex key set 38mm spanner '''Parts Required''' B0000122 Glacier Bush 12 D 14 D 15 Long x 4 D0007454 Stop Sub Base OH (D8377) x 1 D0007455 Stop Damper Housing OH (D8378) x 1 D0008377 Stop Sub Base (D7454) x 1 D0008378 Stop Damper Housing (D7455) x 1 D0008380E Stop Slide Finger ZX4 Mk5 x 1 D0008383 Cross Joiner x 1 D0010756 Proximity Switch Mounting Block Reduced Size x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 H0008379 Shaft 12mm: 263mm R Axis Limit Stainless x 2 P0000235 MC Series self compensating Damper x 2
less x 2 P0000235 MC Series self compensating Damper x 2 )
R0015314 Fit Z Axis Drive components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Engineers level 300mm 5mm Carbide drill 150m verniers '''Parts Required''' A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2 A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2 B0000344 Circlip 15mm External x 2 B0000400 Circlip 17mm External x 2 D0001249 Z Axis Chain Offset Plate x 1 D0001271 Z Axis Chain Mounting Plate x 1 D0001927 Intermediate Housing (AM3032) x 1 D0006498 Z Housing Cap x 2 D0007453 Double Cylinder Bracket OH (D8106) x 1 D0007610 Chain Slide x 1 D0007795 Nut Housing x 1 D0007796 Nut Housing - Mirror x 1 D0007858 Kit: Z Axis Drive Chain ZX + Micro x 1 D0008106 Double Cylinder Bracket (D7453) x 1 H0007714 Z Spocket 20 teeth x 2 R0000963E Bench Assemble Z axis Components x 1
teeth x 2 R0000963E Bench Assemble Z axis Components x 1 )
R0000558E Bench Assemble Base and Turntable Part 2 + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1)
R0015356 Assemble Pneumatics on to electrical cabinet + ('''Tools Required''' … '''Tools Required''' Standard hex keys Standard spanner set Standard drill set Standard tapping set Tape measure Rule '''PartsRequired''' P0000458 x 1 P0001069 x 1 P0001022 x 1 D0001933 x 1 P0001008 x 1 P0000010 x 3 P0001009 x 1 P0001102 x1 P0000009 x 1 P0001163 x 4 P0001073 x 1 P0000159 x 3 P0001101 x 1 P0001108 12mm tee x 1 P0001186 x 3
159 x 3 P0001101 x 1 P0001108 12mm tee x 1 P0001186 x 3 )
R0015095 Bench Assemble Infeed Support Arms + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard tap sete Setting jigs '''Parts required''' B0001170 Spacer 180 off B0001155 open rail 18 off D0015553 Transfer Support arm R/H (right to left machine ) OR D0015552 Transfer Support Arm L/H ( Left to Right machine) D0015554 x 18 M8 x 20 button hex fastener x 18 M5 x 25 socket cap x 180 M5 A form washer x 180ex fastener x 18 M5 x 25 socket cap x 180 M5 A form washer x 180)
R0015093 Bench Assemble Transfer Beam + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard hand taps V rail alignment Jigs Drill driver and 4mm hex fitting '''Parts Required''' B0001155 OpenRail 1000mm Long x 32 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9
2 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9 )
R0000572 Bench Assemble Centralise Assembly + ('''Tools Required''' … '''Tools Required''' standard hex key set Standard spanner set Grease gun '''Parts Required''' B0000005 Angular Contact Bearing 15 I/D 35 O/D 11 Long x 2 B0000065 Bearing Rod End 10mm x 2 D0004363 Middle Link Rod x 1 D0004365 Pivot Clamp x 1 D0004366 Link Clamp Cap x 1 D0004369 Top Link Stud Bolt x 1 D0004370 Middle Link Stud Bolt x 1 D0004393 Lever Joint x 2 D0004394 Joint Shaft x 2 D0004401 Pivot Pin x 1 D0004403 Pivot Pin Nut x 1 D0004406 Retainer Plate x 1 D0004541 Cylinder Swivel End x 2 D0004542 Cylinder Bracket 4542 x 1 D0004622 Centralise Cylinder Spacer x 1 D0004669 Damper Rod End Block x 1 D0004766 Pivot Pin Bolt x 1 H0004367 Centering lever x 1 P0000029 Non Adjustable Damper 100mm x 1 P0000031 Pneumax Microcylinder 25 x 100 Magnetic x 2 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 2 P0001198 fitting speed controller 1/8 x 6mm tube x 2
) x 2 P0001198 fitting speed controller 1/8 x 6mm tube x 2 )
R0000574 Fit Motor and Swarf Chute + ('''Tools Required''' … '''Tools Required''' standard hex keys Standard spanner set 1 meter steel rule Copper slip Chute flap template jig Standard Hss drills Standard taps Ratchet 3/8 drive and 13mm socket Copper/hide hammer '''Parts Required''' B0000048 Taperlock Set SPZ 80-2 1210-24 x 1 B0001175 Saw V-belt (special size 987mm) for 500mm blade x 2 D0005628 Saw chute infill panel x 1 H0004637 Offcut Chute (H0005333) x 1 H0004660 Chute Bracket x 1 P0000609 Reed Switch Mount (Tie Bar) x 3004660 Chute Bracket x 1 P0000609 Reed Switch Mount (Tie Bar) x 3)
R0015037 Bench Assemble SY Assembly Part 2 + ('''Tools Required''' S … '''Tools Required''' Standard Hex Key set Standard Spanner set 1 Meter straight edge Feeler Gauges '''Parts Required''' B0000044 Linear Rail MSB25 260mm Long (AMT) x 2 B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4 B0000173 blanking cap x 10 B0000234 Straight Grease Nipple M6 ST/ST x 4 B0000245 Needle Bearing 12 D 16 D 10 Long (ENA) x 12 B0001060 Grease Fitting M6x0.75 to Ø4 x 4 B0001061 Grease fitting M6 x 1 to 4mm x 4 B0001123 Double angular contact bearing 6 I/D 17 O/D 9 long x 2 B0001185 Leadscrew nut Igus x 1 C0001005 Stepper Motor AS1050 x 1 D0005184 Guide Roller x 6 D0005186 Guide Pin Washer x 6 D0015172 Centralise Plate (with SY) x 1 D0015173 Saw SY Saddle Brace x 1 D0015174 Roller Fence (With SY) x 2 D0015175 Saw Saddle Carriage Block x 2 D0015176 Cylinder Mount Block x 2 D0015178 Z Block x 2 D0015207 Outer Bearing Housing x 1 D0015208 Leadscrew Bearing Block x 1 D0015209 Leadscrew Attachment Bracket x 1 D0015222 SY Grease Manifold x 2 D0015240 Collar Clamp: SY Axis ZX5 x 1 D0015316 Leadscrew Bearing Block Cover x 1 D0015415 Turret Pickup Arm ZX5 x 2 D0015416 Bracket: Turret Stop RH ZX5 x 1 D0015417 Bracket: Turret Stop LH ZX5 x 1 D0015698 Flag Block x 1 D0015777 Leadscrew SY x 1 D0016336 SY table blower x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 H0005185 Shaft 12mm: 90.5 Saw Fence Roller Pin x 6 M0001209 Bracket m8 proximity sensor 90 degree x 1 P0000200 Elbow Adaptor 6mm - M5 x 7 P0001127 Guide cylinder 20 x 30 compact x 2 P0001157 Turret Stop: 6 Station Right Handed Somatec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1matec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1)
R0015250 Bench Assemble Support Arms + ('''Tools Required''' S … '''Tools Required''' Standard hex key set Standard tap sete Setting jigs '''Parts required''' B0001170 Spacer 180 off B0001155 open rail 18 off D0015552 Transfer Support arm R/H (right to left machine ) OR D0015553 Transfer Support Arm L/H ( Left to Right machine) D0015554 x 18 Transfer Support Arm L/H ( Left to Right machine) D0015554 x 18)
R0015064 Bench Assemble Clamp Assembly Part 2 + ('''Tools Required''' S … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers 20mm bearing dolly Reduced shank 5mm hex key '''Parts Required''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 8 B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8 B0000200 Circlip 8mm External x 12 B0000346 Ball Bearing 8 D 22 D 7 Long + seals x 6 D0004331 Clamp Head (D7450) x 1 D0004332 Clamp Mount Block (D7449) x 1 D0004333 Pillar x 2 D0004358 Clamp Head Bracket (D7447) x 1 D0004359 Clamp Head Cylinder Bar (D7446) x 2 D0004550 Clamp Insert x 2 D0004808 Slide Stop x 2 D0005191 Bearing Protective Washer x 4 D0005425 Clamp block Right (5625) x 1 D0005566 Clamp block left - Roller style (5567) x 1 D0005568 Clamp block left roller shaft x 3 D0007447 Clamp Head Bracket OH (D4358) x 1 D0007449 Clamp Mount Block OH (D4332) x 1 D0007450 Clamp Head OH (D4331) x 1 D0015266 Shaft 38.7mm: 440mm ZX Saw Top Clamp BZP x 2 D0015299 Shaft 16mm: 320mm Chip Deflector ZX5 x 1 D0015446B Chip Deflector Mounting Plate (Tapped) x 1 D0015447B Chip Deflector Probe Ø50 (Tapped) x 2 D0015454 Chip Deflector Rod (M16) x 2 H0004625 Shaft 16mm: 150 Saw Clamp x 2 H0004626 Shaft 16mm: 275 Eject Push x 1 H0004627 Shaft 20mm: 210 Saw Inner Clamp x 2 H0004628 Shaft 20mm: 245 Saw Outer clampx 2 M0001194 Kipp clamp handle x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000054 Cylinder Ø32 x 50 (PIS32A50) x 1 P0000064 Pneumax microcylinder 25bore x 80stroke x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1)
R0000571 Fit and Level Cut Tables , Finalise Eject + ('''Tools Required''' … '''Tools Required''' 1 meter straight edge 500mm rule Standard hex key Standard spanner set Feeler gauges Engineers level Adjustment shim '''Parts Required''' A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 0.5 A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 1 A0001074 igus mounting bracket set x 1 D0004551 Cylinder Spacer x 1 D0004553 Cover Fixing Bar x 1 D0004554 Bar Spacer Short x 1 D0004555 Bar Spacer Long x 1 D0004769 Ejector Clamp Pad to be made in conjuction with D5121 (5305) x 1 D0004770 Infeed Clamp Pad to be made in conjunction with D5122 (5299) x 1 D0005121 Ejector Clamp Stainless Pads (5306) x 1 D0005122 Infeed Clamp Pad (5300)x 1 D0005199 Ejector Cover x 1 D0005412 Energy Chain Adapter Plate x 1 H0004556 Fixing Bar Gap Cover (5297) x 1 H0004656 Material Trip Stripx 1 P0000368 Extension 1/8 bsp x 22 long x 1 P0000443 Cleanline Cylinder 32 x 450 PN11246 x 1 P0000444 Reed Switch: Pneumax 1580U (5.0m Lead) x 2 P0001198 flow controller 6mm elbow 1/8 x 2580U (5.0m Lead) x 2 P0001198 flow controller 6mm elbow 1/8 x 2)
R0015350 Fit Rigid Ducting + ('''Tools Required''' … '''Tools Required''' Duct tape '''Parts Required''' M0000116 Ø200mm to 3 way (Ø125mm) extractor pipe connector x 1 M0000118 Ø200mm - 90 deg Bend Ducting x 1 M0000185 Ø125 mm ID 45 degree bend x 1 M0001045 Rigid Ducting Ø125 x 1000mm x 2 M0001213 Rigid Ducting Ø200mm x 500mm x 2 M0001214 Rigid Ducting Ø200 x 2000mm long x 3 M0001228 Extraction Unit inlet taper x 3
mm long x 3 M0001228 Extraction Unit inlet taper x 3 )
R0015256 Pneumatic Connections + ('''Tools Required''' … '''Tools Required''' Pipe cutters Number identification Flush cutters '''Parts Required''' P0000160 Flow regulator 6mm inline x 2 P0000551 6mm inline Quick Exhaust Fitting x5 P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x 1 P0001023 Fitting: SMC 6mm mini Y x 1 P0001030 Fitting: SMC 6mm Equal Tee x 27 R0015071 Pneumatics rail A0000343 energy chain x 1 A0000344 energy chain bracket set x 1 D0015577 fixed energy chain bracket x 1 P0001166 Tube to tube elbow 12mm x 1
rgy chain bracket x 1 P0001166 Tube to tube elbow 12mm x 1 )
R0015027 Install Pneumatic Connection rail and Air Feeds + ('''Tools Required''' … '''Tools Required''' Standard hex key set Pipe cutters Standard spanner set '''Parts Required''' D0015578 Energy Chain Bracket - Moving x 2 P0000551 6mm inline Quick Exhaust Fitting x 6 P0000046 6mm y fitting x 6 R0015289 Bench assemble pipe connection rail
ting x 6 R0015289 Bench assemble pipe connection rail )
R0015046 Bench Assemble Infeed Clamps + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers Grease for lubrication M0000494 '''Parts Required''' B0000062 Circlip 20mm External x 2 B0000070 Linear Bearing: Ø25 x 40 Compact (Metal Case Only) x 8 B0001176 Washer :bearing shim x 3 D0000209 Shaft Strap (D8709) x 1 D0000211 Cylinder Extension x 1 D0001331 Roller Ø40 x 27 c/w bearing x 3 D0001334 Roller Ø40 x 102 c/w bearing x 2 D0003108 Shaft 20mm: 146mm Clamp Roller Shaft x 2 D0003788 Z Roller Pin (40mm) x 3 D0007680 Infeed Rail x 1 D0007774 Top Roller Block x 1 D0007792 Z Roller Block (D8711) x 1 D0007793 Z Roller Plate (D8710) x 1 D0015427 MC Hold Clamp Bar x 1 D0015428 Top Clamp Block Ø30 15 x 1 H0007773 Shaft 25mm: 268mm ZX Infeed Clamp Top x 2 H0007791 Shaft 25mm :250mm ZX Infeed side x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000010 elbow 6mm 1/8 fitting x 1 P0000200 Elbow Adaptor 6mm - M5 x 2 P0000484 Cylinder 32 x 100 stroke x 1 P0001160 Cylinder 32 x 70 stroke x 1 P0001198 Fitting: flow control 1/8 x 6mm elbow x 4 M0000253 anti slip pad 22mm x 1
rol 1/8 x 6mm elbow x 4 M0000253 anti slip pad 22mm x 1 )
R0015041 Bench Assemble Top Hood Assembly + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard Hss drill set Standard tap set Acoustic foam cutting board and straight edge Utility Blade '''Parts Required''' Pre wired light, beacon and network cable from electrical department C0001152 Camera: HikVision DS-2CD2343G0-I-2.8mm x 1 C0001239 Micro SD Card 32Gb Class 10 x 1 D0000770 Door Hinge (M0016) x 2 D0001877 Saw Top Door Mk4 x 1 D0004641 Hinge Pin Block (D7445) x 1 D0004642 Flap Counterbalance Bar x 1 D0004645 Safety Flap Hinge Pin x 1 D0004679 Flap Stiffening Bar x 1 D0004705 Flap Hinge Bar x 1 D0004747B top door screen x 1 D0004807 Flap x 1 D0007445 Hinge Pin Block OH (D4641) x 1 D0016251 Saw Hood Switch Mount Plate (Bernstein) x 1 E0000275 Button: Base Fixing 1 N/C x 1 E0001072 Emergency Stop Module Bevelled 1NO 1NC x 1 E0001569 Guard Lock Switch: Bernstein Radius Actuator (Key) x 1 H0004643 4mm Axxis Clear 145mm x 690mm x 1 M0000002 12mm Grey Acoustic Foam with Black PVC Facing x 1 (consumable stock ) M0000036 Sign - Ear Protection x 1 M0000048 Gas Spring 15mm x 100mm x 1 M0000539 Handle Black Nylon 200mm M8 Fixings x 1
100mm x 1 M0000539 Handle Black Nylon 200mm M8 Fixings x 1 )
R0000962E Bench assemble Y axis Components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Fine emery tape solvent Standard drill set '''Parts Required''' B0000086 Ball Bearing 15 D 32 D 9 Long + seals x 2 B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals x 1 B0000236 90 Deg Grease Nipple M6 ST/ST x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1 D0006488 Y Leadscrew Sleeve x 1 H0007789 Y Leadscrew x 1
0006488 Y Leadscrew Sleeve x 1 H0007789 Y Leadscrew x 1 )
R0015064 Bench Assemble Clamp Assembly + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers 20mm bearing dolly Reduced shank 5mm hex key '''Parts Required''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 8 B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8 B0000200 Circlip 8mm External x 12 B0000346 Ball Bearing 8 D 22 D 7 Long + seals x 6 D0004331 Clamp Head (D7450) x 1 D0004332 Clamp Mount Block (D7449) x 1 D0004333 Pillar x 2 D0004358 Clamp Head Bracket (D7447) x 1 D0004359 Clamp Head Cylinder Bar (D7446) x 2 D0004550 Clamp Insert x 2 D0004808 Slide Stop x 2 D0005191 Bearing Protective Washer x 4 D0005425 Clamp block Right (5625) x 1 D0005566 Clamp block left - Roller style (5567) x 1 D0005568 Clamp block left roller shaft x 3 D0007447 Clamp Head Bracket OH (D4358) x 1 D0007449 Clamp Mount Block OH (D4332) x 1 D0007450 Clamp Head OH (D4331) x 1 D0015266 Shaft 38.7mm: 440mm ZX Saw Top Clamp BZP x 2 D0015299 Shaft 16mm: 320mm Chip Deflector ZX5 x 1 D0015446B Chip Deflector Mounting Plate (Tapped) x 1 D0015447B Chip Deflector Probe Ø50 (Tapped) x 2 D0015454 Chip Deflector Rod (M16) x 2 H0004625 Shaft 16mm: 150 Saw Clamp x 2 H0004626 Shaft 16mm: 275 Eject Push x 1 H0004627 Shaft 20mm: 210 Saw Inner Clamp x 2 H0004628 Shaft 20mm: 245 Saw Outer clampx 2 M0001194 Kipp clamp handle x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000054 Cylinder Ø32 x 50 (PIS32A50) x 1 P0000064 Pneumax microcylinder 25bore x 80stroke x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1
etal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1 )
R0015340 Drill, Assemble and Mount Electrical Cabinet + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set 1000mm rule '''Parts Required''' A0000164K Electrical Cabinet (Machined Door) x 1 D0010746 Cabinet Main Mount x 2 D0010747 Cabinet Brace x 2 D0010771 Electrical Cabinet Swing Arm Pin x 2
t Brace x 2 D0010771 Electrical Cabinet Swing Arm Pin x 2 )
R0015255 Mount Assemblies to Main Frame + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0015291 Datum Flag x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 2 D0015722 Energy Chain Tray Shallow Long x 1 D0015861 Energy Chain Cable Support x 1 R0015007 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015251 Bench Assemble X axis components and energy chain R0015004 Bench Assemble Gripperaxis components and energy chain R0015004 Bench Assemble Gripper)
R0015035 Bench Assemble V Notch Components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set Vernier 150mm 2 meter straight edge 40mm shaft pin jigs Feeler gauge set Internal circlip pliers External circlip pliers 8mm hand reamer '''Parts Required''' B0000041 5 x 5 x 19 key x 1 B0000109 Linear Bearing (IKO) 40 D x 62 D x 80 L x 8 B0000427 Leadscrew Ø25x10 435 Long x 1 B0001047 Fixed Bearing Support Block Ø17 x 1 B0001120 Circlip 62mm External x 16 B0001127 ROTEX GS Coupling Ø14/Ø15 Bore & Key (98 Shore Spider) x 1 B0001134 Ball Bearing 15ID 35OD 11 Long x 10 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 D0010132 SZ Drive Mount Plate x 1 D0010563 Y Axis Servo Mount x 1 D0015147 V Notch Upper Support Bar x 1 D0015148 V Notch Lower Support Bar x 1 D0015149 VZ Shaft End Plate x 4 D0015152 V-Notch Upper Moving Bar x 1 D0015153 V-Notch Rear Moving Bar x 1 D0015154 V-Notch Front Moving Barx1 D0015157 Saw Motor Bar x 4 D0015158 Shaft 40mm: 190mm ZX V Notch Saw Motor Slide x 8 D0015159B Saw Motor Adjustment Screwx 4 D0015160 Saw Motor Block x 4 D0015164 VY Leadscrew Block x 1 D0015166 VY Motor Mounting Plate x1 D0015258 Upper Link Mount 1 x 1 D0015259 Upper Link Mount 2 x 1 D0015260 Upper Link x 2 D0015261 Lower Link x 2 D0015262 Lower Link Mount x 2 D0015263 Mid Link Shaft x 2 D0015264 Lower Link Shaft x 2 M0001093 Shaft Clamping Element (Ø15-20 shafts) x 16
haft x 2 M0001093 Shaft Clamping Element (Ø15-20 shafts) x 16 )
R0015301 Fit terminal holders and Ethercat boxes + ('''Tools Required''' Standard screwdriver set Standard hex key set '''Parts Required''' E0000519 Relay x 8 A0000160 Relay base x 8 C0001018 Ethercat box x 8 D0010806 Mounting plate x 8)
R0015298 Bench Assemble V notch Clamps + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard Spanner set External circlip pliers '''Parts Required''' B0000415 Ball Bearing 20 I/D 32 O/D 7 Long + shields (INA) x 8 B0001176 Washer : bearing shim x 9 D0001313 Datum Roller (Radial Bearing) x 2 D0010060 Roller Shaft Ø20 x 37.5 x 3 D0010061 Datum Roller Ø40 x 20 x 3 D0010065 Shaft 16mm: 115mm Autoflow Infeed Roller x 2 D0010066 Infeed Roller Connector x 1 D0010545 Infeed Roller Mount x 2 D0010546 Infeed Roller Attachment x 1 D0015211 Outfeed Clamp Upright x 2 D0015212 Top Clamp Mounting Plate x 1 D0015213 Side Clamp Mounting Block x 1 D0015221 Outfeed Roller Bed Mounting Plate x 1 D0015241 Outfeed Side Clamp Mounting Block x 1 D0015242 Outfeed Front Fence x 1 D0015243 Outfeed Top Clamp Plate x 1 D0015244 Outfeed Top Clamp Mounting Plate x 1 D0015245 Outfeed Top Clamp Leg x 2 D0015246 Centre Side Clamp Roller Block x 1 M00001004 Endcap 40 x 40 black x 2 M0001006 Threaded insert M14-M8 30 long x 4 M0001017 Endcap 80x40 Black x 2 P0000010 6mm elbow x 4 P0001045 Guide cylinder 25 x 150 x 2 P0001132 Cylinder 32x 175 guided x 2 P0001198 Fitting: Speed controller 1/8" x 6mm Elbow x 4
P0001198 Fitting: Speed controller 1/8" x 6mm Elbow x 4 )
R000569E Bench Assemble Head Spindle Posts + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Internal circlip pliers Consumable 4mm yellow grease line Pneumatic pipe cutters '''Parts Required''' B0000002 Bearing: 12/28dia x 8mm Sheilded x 2 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001061 Grease fitting x 6 D0004001 Head Bearing Block x 3 D0004021 Upstroke Plate x 1 D0004078 Motor Plate (5311) x 1 D0004099 Cylinder Bearing Block x 1 D0004256 Cylinder rod bar x 1 D0004343 Lower Damper Bracket (5313) x 1 D0004445 Semi circular slit strip (5533) 500mm x 1 D0004634 Chute Sawblade Strip 500mm (5532) x 1 D0004733 Belt Adjuster Pulley x 1 D0004734 Belt Adjusting Bar x 1 D0004735 Belt Adjuster Pin x 1 D0010780 Grease Manifold x 1 H0004444 Semi-circular Guard (5332) x1 P0000009 Fitting: 1/4 BSPT - 6mm Elbow x 2 P0000037 Magnetic Cylinder 40 x 185 with 15mm rod extension x 1 P0000308 Flow Controller In Line 6mm x 1
rod extension x 1 P0000308 Flow Controller In Line 6mm x 1 )
R0015037 Bench Assemble SY Assembly + ('''Tools Required''' … '''Tools Required''' Standard Hex Key set Standard Spanner set 1 Meter straight edge Feeler Gauges '''Parts Required''' B0000044 Linear Rail MSB25 260mm Long (AMT) x 2 B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4 B0000173 blanking cap x 10 B0000234 Straight Grease Nipple M6 ST/ST x 4 B0000245 Needle Bearing 12 D 16 D 10 Long (ENA) x 12 B0001060 Grease Fitting M6x0.75 to Ø4 x 4 B0001061 Grease fitting M6 x 1 to 4mm x 4 B0001123 Double angular contact bearing 6 I/D 17 O/D 9 long x 2 B0001185 Leadscrew nut Igus x 1 C0001005 Stepper Motor AS1050 x 1 D0005184 Guide Roller x 6 D0005186 Guide Pin Washer x 6 D0015172 Centralise Plate (with SY) x 1 D0015173 Saw SY Saddle Brace x 1 D0015174 Roller Fence (With SY) x 2 D0015175 Saw Saddle Carriage Block x 2 D0015176 Cylinder Mount Block x 2 D0015178 Z Block x 2 D0015207 Outer Bearing Housing x 1 D0015208 Leadscrew Bearing Block x 1 D0015209 Leadscrew Attachment Bracket x 1 D0015222 SY Grease Manifold x 2 D0015240 Collar Clamp: SY Axis ZX5 x 1 D0015316 Leadscrew Bearing Block Cover x 1 D0015415 Turret Pickup Arm ZX5 x 2 D0015416 Bracket: Turret Stop RH ZX5 x 1 D0015417 Bracket: Turret Stop LH ZX5 x 1 D0015698 Flag Block x 1 D0015777 Leadscrew SY x 1 D0016336 SY table blower x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 H0005185 Shaft 12mm: 90.5 Saw Fence Roller Pin x 6 M0001209 Bracket m8 proximity sensor 90 degree x 1 P0000200 Elbow Adaptor 6mm - M5 x 7 P0001127 Guide cylinder 20 x 30 compact x 2 P0001157 Turret Stop: 6 Station Right Handed Somatec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1
1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1 )
R0015038 Bench Assemble V notch Datum Rollers + ('''Tools Required''' … '''Tools Required''' Standard Hex key set External circlip pliers 1 meter straight edge Feeler gauges '''Parts Required''' B0000062 Circlip 20mm External x 13 B0000415 Ball Bearing 20 I/D 32 O/D 7 Long + shields (INA) x 26 B0001176 washer : bearing shim x 16 D0010060 Roller Shaft Ø20 x 37.5 x 7 D0010061 Datum Roller Ø40 x 20 x 6 D0010396 Datum Roller Ø40 x 150mm x 7 D0010397 Shaft 20mm: 195mm Autoflow Roller x 7 D0015214 Roller Support Bar - Short x 1 D0015217 Profile Support Pad x 2 D0015218 Roller Support Bar - Long x 1 D0015220 Outfeed Roller Bed Support Frame x 1 D0015221 Outfeed Roller Bed Mounting Plate x 1 D0015348 MC Outfeed Roller Mounting Plate x 1 M0001006 Threaded insert M14/M8 30 long x 8
ting Plate x 1 M0001006 Threaded insert M14/M8 30 long x 8 )
R0000706 Bench assemble Infeed Datum rollers + ('''Tools required''' … '''Tools required''' External circlip pliers Standard hex key set Pipe cutters Pneumatic identification numbers '''Parts Required''' B0000062 Circlip 20mm External x 6 D0001176 Washer : bearing shim x 3 D0001333 Roller Ø40 x 80 c/w bearing x 3 D0001334 Roller Ø40 x 102 c/w bearing x 3 D0003108 Shaft 20mm: 146mm Clamp Roller Shaft x 3 D0007677 Infeed Base Rail (D2972) x 1 D0007942 Shaft 20mm: 119.4mm ZX Datum Roller Circlip x 3 D0010896 Infeed Clamp Blower Vert x 1 D0010897 Infeed Clamp Blower x 1 P0000053 6mm T (P16) x 1 P0000160 Fitting: Flow Controller In Line 6mm x 16mm T (P16) x 1 P0000160 Fitting: Flow Controller In Line 6mm x 1)
Laser Setup on Flowline/ZX3 for Laser Holes + ('''How to Setup .''' This will Cover the … '''How to Setup .''' This will Cover the Basic Alignment of the receiver and Sender setup. Focusing the Laser and Setting up the Receiver Sensitivity. Always Make sure Laser Sender and Receiver are clean and both lenses have been wiped with a soft cloth first.
en wiped with a soft cloth first. )
GY GZ axis setup with Jetter Motors + ('''WARNING:''' '''The Jetter motor on th … '''WARNING:''' '''The Jetter motor on the GZ axis has a brake. Releasing the brake without control could be harmful/dangerous.''' '''Use the Air Counterbalance rig to assist if necessary.''' This assumes that the motors are connected to the Beckhoff drive and are free to move.o the Beckhoff drive and are free to move.)
DM - Updating Resources + (<div class="icon-instructions caution-i …

...This procedure is now obsolete - it is kept for historical purposes only

All information provided to the service engineers on Device Magic can all be linked to a single Excel document. This document provides all customer names, machine numbers, emails and employee information. Linking this document with Device Magic provides fields that make it easier for engineers to fill out the form.

This document must only be used internally at Stuga and not be sent to engineers or customers in coordination with Data Protection standards.

used internally at Stuga and not be sent to engineers or customers in coordination with Data Protection standards.</div> </div> )
Commissioning a Beckhoff Axis + (<div class="icon-instructions dont-icon"> <div class="icon-instructions-icon"></div> <div class="icon-instructions-text">...Any stepper motor drives will need the EP7041 drive to be programmed first</div> </div>)
R0015066 Bench Assemble Saw Motor Assembly + ('''Tool Required''' … '''Tool Required''' Standard hex key set Standard spanner set Cutting disc Standard hand taps '''Parts Required''' A0000013 32mm Conduit Adaptorx 1 A0000027 Flexible Conduit Ø32mm x 1 D0004079 Saw Motor (Modified Front Flange) x 1 D0004437 Motor Conduit Bracket x 2 D0004835 Flex conduit plate x 1 D0004997 Connector Support Block (5360) x 1 D0004999 Reed Switch Terminal Box x 1 D0005219 Turntable Nozzle x 1 D0008198 Chute Flap x 1 H0008200 Chute Flap Bracket x 1 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1
1 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1 )
R0015246 Fit Hepco Drive Beam Cylinder + ('''Tools Required''' … '''Tools Required''' Standard hex key set Ball pein hammer Standard spanner set '''Parts Required''' D0015074 Cylinder Support x 2 D0015075 Cylinder Bracket x 4 D0015077B Cylinder Drive Adapter x 1 D0015144 Datum Switch Bracket x 2 D0015948 ZX5 Beam Move Cylinder Guard x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2 P0000109 RB Series Shock Absorber x 2 P0001118 cylinder 50 x 700 rodless x 1 P0001145 Fitting smc flow controller elbow 10-1/4 bsp F0000315 D nut M8 x 4itting smc flow controller elbow 10-1/4 bsp F0000315 D nut M8 x 4)
R0015244 Frame ancillaries Fitting + ('''Tools Required''' … '''Tools Required''' 115mm disc cutter Standard Hex key set Standard spanner set Standard tape measure Standard Tap set Standard HSS drill set '''Parts Required''' A0001060 Support bracket :Cable basket Tray x 5 A0001061 Retainer: Wire Basket Cable Tray x 7 A0001065 Wire cable tray 3m length x 2.5 D0015611 Reference Levelling Bracket x 2
y 3m length x 2.5 D0015611 Reference Levelling Bracket x 2 )
R0015284 Frame ancillaries + ('''Tools Required''' … '''Tools Required''' 115mm disc cutter Standard Hex key set Standard spanner set Standard tape measure Standard Tap set Standard HSS drill set '''Parts Required''' A0001060 Support bracket :Cable basket Tray x 5 A0001061 Retainer: Wire Basket Cable Tray x 7 A0001065 Wire cable tray 3m length x 2.5 D0015611 Reference Levelling Bracket x 2ble tray 3m length x 2.5 D0015611 Reference Levelling Bracket x 2)
R0015029D Hepco Beam Alignment + ('''Tools Required''' … '''Tools Required''' Engineers level Hepco flat spanner Hepco Box spanner Standard hex key set Incremental shim pack Torque wrench '''Parts Required''' B0000184 Journal Cap Seal 34 x 4 B0000185 Double Row Long Stud Journal Eccentric x 2 B0000186 Double Row Long Stud Journal Concentric x2 B0001102 Double Edge Spacer Slide and Beam 7600mm x 1 D0015072 Carriage Plate x 1 D0015492 Vertical Beam Adjustment Plate x5 D0015493 Lateral Beam Adjustment Plate x 5 P0000200 Elbow Adaptor 6mm - M5 x 1 F0000529 T-Nut M6 (slot 10) x 3 F0000530 T-nut M8 (slot 10) x11 F0000529 T-Nut M6 (slot 10) x 3 F0000530 T-nut M8 (slot 10) x1)
R0015029D Hepco Beam Alignment Part 2 + ('''Tools Required''' … '''Tools Required''' Engineers level Hepco flat spanner Hepco Box spanner Standard hex key set Incremental shim pack Torque wrench '''Parts Required''' B0000184 Journal Cap Seal 34 x 4 B0000185 Double Row Long Stud Journal Eccentric x 2 B0000186 Double Row Long Stud Journal Concentric x2 B0001102 Double Edge Spacer Slide and Beam 7600mm x 1 D0015072 Carriage Plate x 1 D0015492 Vertical Beam Adjustment Plate x5 D0015493 Lateral Beam Adjustment Plate x 5 P0000200 Elbow Adaptor 6mm - M5 x 2 F0000529 T-Nut M6 (slot 10) x 3 F0000530 T-nut M8 (slot 10) x12 F0000529 T-Nut M6 (slot 10) x 3 F0000530 T-nut M8 (slot 10) x1)
R0015274 Fit X Axis Gearbox and Motor + ('''Tools Required''' … '''Tools Required''' Feeler gauge set Standard hex key set Standard Tap set Torque wrench (0-50nm) Extended 4mm hex bit 1/8 drive '''Parts Require''' D0015073B x 1 C0001212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 201212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 2)
R0015247 Fit X axis gearbox and Motor + ('''Tools Required''' … '''Tools Required''' Feeler gauge set Standard hex key set Standard Tap set Torque wrench (0-50nm) Extended 4mm hex bit 1/8 drive '''Parts Require''' D0015073B x 1 C0001212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 201212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 2)
R0015271 Mount buffer bars + ('''Tools Required''' … '''Tools Required''' Standard Hex key set '''Parts Required''' D0015463 Infeed Front Endfence x1 D0015464B Infeed Rear Endfence x 1 D0015465 Endfence Spacer - Short x 3 D0015466 Endfence Spacer - Long x 3 D0016335 light curtain mounting post x 1ence Spacer - Long x 3 D0016335 light curtain mounting post x 1)
R0008013-ECO Ecoline dipper arm clacker + ('''Tools Required''' 1 … '''Tools Required''' 10mm spanner 5mm punch Ball pein hammer '''Parts Required''' D0003196 Dipper Arm ( Ecoline) x 1 D0003197 Dipper Base ( Ecoline) x 1 D0003894 Flapper pivot pin x 1 M0000101 Compression Spring 11 D 15 D 25 Long x1 F0000185 M6 x 16 Hex set S/S x 1sion Spring 11 D 15 D 25 Long x1 F0000185 M6 x 16 Hex set S/S x 1)
R0015310 Install V Notch Subframe + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard Spanner set Parallel setting blocks 600mm rule 1 meter straight edge 2 meter straight edge 12 " engineers level 12" engineers square '''Parts Required''' D0015151 Shaft End Washer x 8 D0015155 Vertical Spacer Bar x 4 D0015150 shaft 40mm zx v notch x 4 D0015169B cylinder rod bracket x 2 R0015035 Bench Assemble V Notch Componentsinder rod bracket x 2 R0015035 Bench Assemble V Notch Components)
R0008013 Clacker assembly + ('''Tools Required''' … '''Tools Required''' 10mm spanner 5mm punch Ball pein hammer '''Parts Required''' D0008339 Gap Closer Arm x 1 D0008340 Gap Closer Base x 1 D0008496 Clacker Pins x 1 M0000101 Compression Spring 11 D 15 D 25 Long x1 F0000185 M6 x 16 Hex set S/S x 1
g 11 D 15 D 25 Long x1 F0000185 M6 x 16 Hex set S/S x 1 )
R0015317 Install Rotary Ring + ('''Tools Required''' … '''Tools Required''' Standard Hex Key set Standard spanner set Lifting Strop Overhead crane operation Torque wrench Soft hammer Ring lubrication oil '''Parts Required''' A0000309 Domed Blanking Plug 19mm x 3 C0001123 Servo Motor: Beckhoff AM8062 18Nm 3000rpm x 1 D0000263 Stop Y Central x 1 D0002990E Strike Post ZX4 Mk5 x 1 D0002991 Switch carrier x 1 D0006061 Timing Belt cap x 1 D0007861 Y axis hard stop x 2 D0010756 Proximity Switch Mounting Block Reduced Size x 2 D0010894 Ethercat Cover ZX3/ZX4 x 1 D0015542 R Axis Motor Connector Cover x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2 H0007995 Rotary base cover plate x 2 M0000451 Plug and Elbow x 2 R0000971E Bench Assemble R Axis Gearbox R0010260 Bench Assemble Tool Break Sensor R0015138 Machining Head ZX4 Mk5 (Quad Plunge)
Break Sensor R0015138 Machining Head ZX4 Mk5 (Quad Plunge) )
R0015101 Bench Assemble Take Up Assembly + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set '''Parts Required''' D0008281 Takeup Boss Cap x 4 D0015581 Fixed Pivot Bracket x 4 D0015584 Cylinder Trunnion Plate x 1 D0015590 Takeup Arm ZX5 x4 D0015593 Takeup Arm Pin ZX5 x 4 D0015595 Takeup Arm Washer 4mm x 4 D0015596 Takeup Bearing Block Short x 4 D0015605 Fixed Pivot Bracket End Plate x 4 D0015736 Hard Stop Backplate x 1 D0015737 Hard Stop Shaft x 1 M0001077 Rubber bump stop M6 x 1 P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 1 P0001075 Trunnion Pin for CG1 Cylinder x 1 P0001076 Trunnion Bracket for CG1 x 1 P0001112 Cylinder 32 x 125s Locking P0001198 Fitting: Speed Controller 1/8" x 6mm Tube
Locking P0001198 Fitting: Speed Controller 1/8" x 6mm Tube )
R0015335 Mount Electrical Cabinet + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set Standard Tap set '''Parts Required''' D0004391E Left hand side sheet x 1 D0015425 Bracket: Beckhoff Box Right Angle x 1 D0015426 Mounting Plate: Airgun Assy x 1 D0015425 Beckhoff right angle mounting plate x 1 P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 1 P0000021 Airgun Assembly x 1 P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2 P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1 P0000278 Regulator 0-2 bar x 1 P0000373 Regulator fixing bracket x 1 R0015016C Electrical cabinet wiring Mod F
xing bracket x 1 R0015016C Electrical cabinet wiring Mod F )
R0015291 Install Transfer Beams To Module C and E + ('''Tools Required''' Standard hex key set Module pitching jigs Tape measure 7.5 meter Engineers level 1 meter spirit level '''Parts required''' Pre assembled transfer beams)
R0002794E Mount Width sensor + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Hack saw '''Parts Required''' D0000655 Magnet mounting block x 1 E0000461B Analogue linear sensor x 1 E0000463 Captive magnet with ball joint x 1 M5 studding (consumable stock )tive magnet with ball joint x 1 M5 studding (consumable stock ))
R0015091 Mount Outfeed Beam Sensor + ('''Tools Required''' … '''Tools Required''' Standard hex key set Tape measure '''Parts Required''' D0015546 Reflector Mounting Plate x 1 D0015701 Maytec Post x 2 D0016322 Welded 90° Bracket: 76mm x 38mm x 38mm x 2 E0000279 Spare Reflectors for E0265 x 1 E0001139 Sensor: Outfeed Beam x 1 M0001059 Sensor Mount Bracket E1139 x 1 Sensor: Outfeed Beam x 1 M0001059 Sensor Mount Bracket E1139 x 1)
R000562 Bench Assemble Centralise Top Table + ('''Tools Required''' … '''Tools Required''' Standard hex key set Consumable M8 studding Hacksaw and file 16mm hand reamer 1 meter straight edge '''Parts Required''' B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 4 D0004138 Centralising Bearing Block x 4 D0004337 Slide Bar Holder x 1 D0004338 Slide Support Bar x 1 D0004545 Slide Support End x 2 D0005235 Support Post x 2 D0005236 Support Post x 2 H0004624 Shaft 16mm: 343 Centralise x 2
6 Support Post x 2 H0004624 Shaft 16mm: 343 Centralise x 2 )
TB0444 Renewing CF Card on TwinCAT2 Systems + (Problem These machines … Problem These machines use a CX5020 PC with a 2Gb CF card running TwinCAT2 PLC system. The CF card can fail, which is effectively the windows operating system. The CF card has a very small capacity, so needs to be created from an image. This TB outlines the steps in the process to ensure a successful conclusion. 1. Create a new CF card at stuga using the beckhoff imaging tool on a CX5020 2. Boot up with the CX5020 3. Ensure PLC is set to Enable on start-up (default is config mode) 4. Rename the PC 5. Install TeamViewer host v10 or less from a USB stick 6. If you have a copy of the version of winMulti it was running, copy this in to the c:\ multi folder. If not, a “'''''new version install'''''” will be needed so copy in data from the g:\builds\PC Installs\Autoflow\Multi folder 7. Set up and customer specific network parameters to ensure TeamViewer will work when it is plugged in on site 8. Send to customer Once on site, follow procedure A if the winMulti version is preserved, or B if it is a '''''new version install'''''eserved, or B if it is a '''''new version install''''')
Setting up TwinCAT Drive Manager for AX8000 Drives + (AX8000 drives require a Measurement projec … AX8000 drives require a Measurement project to be added which gives you a specialised drive manager screen for these drives This needs to be installed separately form a file that can be downloaded from Beckhoff or is in g:\design\TwinCAt3 TE5950-TC3-Drive-Manager-2.zipn\TwinCAt3 TE5950-TC3-Drive-Manager-2.zip)
Correcting Linearity with Rack Offset File + (Accuracy problem on A2001 was traced to a … Accuracy problem on A2001 was traced to a non-linear rack. This tutorial demonstrates how to test the linearity of a rack and the systems in place to correct the linearity.

Modifying the linearity of a rack is a very complex and sensitive issue. You must be absolutely certain that there is a case for linearity with REPEATED tests that produce the same result. It is far more likely that accuracy problems are cause by other mechanical issues. This is the only machine in the 20 year history that has needed these alterations

machine in the 20 year history that has needed these alterations</div> </div>)
ZX5 - ZX3 Hepco alignment Module E Saw Infeed +
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Alignment criteria and steps for correct machine installation)
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Alignment details and level settings for correct alignment of module B to module C)
Updating Zebra Firmware on ZD620 model + (Auto calibration upon Power up on the ZD620 printers only works with V84.20.20Z or above, for this reason we may need to check the firmware version on the Printer.)
Autocut Taking A Backup + (Backing up is vital to ensure your data is safe in case there is a failure of the PC or Hard Disk Drive)
Saw machining centre alignment and level check points + (Bullet pointed checks to determine correct alignment of key components within Sawing unit)
Commissioning - Z-Block Calibration + (Commonly used during sawing on Z transoms, … Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing. There are 6 possible states the z block can be in. Each of these can have a different length of protrusion for different profiles. 12 x M8 Screws 12 x M8 Nuts 12 x wire numbers 1 - 6ws 12 x M8 Nuts 12 x wire numbers 1 - 6)
R0000711 Rotary Base Assembly REV2 + (Detailed steps to correctly install rotary … Detailed steps to correctly install rotary gear and journals Checks for correct installation of oil feed system Tolerance limits and requirements '''Tools Required''' Standard hex key set 0-25mm micrometer Ring support blocks for assembly Work Table Mag Base and D.T.I Hepco flat spanner 17mm socket Torque Wrench '''Parts required''' D0006423-2mod Drive ring x 1 D0007651 Face plate x 1 B0000185 journal x 6 B0000186journal x 2 D0006503 Journal washer x 8 D00007692 wiper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1iper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Details and steps for correct alignment of Module A to Module B '''Tools Required''' Laser Level 300mm rule 1 meter yellow level 24mm spanner Permanent marker Pipe cutters Ring main connection equipment)
ZX5 Production R0000548E Module G to R0015040 Module F alignment + (Details for correct alignment of module G to module H To include fitting of front safety tray once module G is installed)
R0000204 Notching gear boxes assembly + (For longevity and correct running , it is … For longevity and correct running , it is imperative these units are assembled to the correct tolerances and assembled in the way detailed by this procedure Tools required Standard Hex Key Set Castle nut spanner Loctite 243 thread lock Loctite 641 bearing fit Mandrel jig Grease applicator Fe10 solvent spray
ease applicator Fe10 solvent spray )
Placing a TwinCAT3 Machine Under Source Control + (<div class="icon-instructions caution-i …

...Note - This dokit is now obsolete - the sourcetree system has been replaced by the internal one in TcXAEShell

Click [https://stuga.dokit.app/wiki/Changing_Version_Control_to_Visual_Studio here] for the latest procedure For many years, the source code for the PLCs has resided on the G:\drive and then a copy on each and every one of the PCs used to edit the code, so at least one on each machine. This is a recipe for disaster because maintaining all the copies and version numbers is incredibly difficult and adds a lot of time overhead to fixes and changes. This has worked because there has been only one developer, but this is set to change in future as more programmers will be trained and tracking versions becomes more difficult From 2020, the PLC code version control has been improved by using an industry standard source control system called "Git" along with "BitBucket" to store the PLC code in the cloud. The program "SourceTree" is used to commit, push and pull the changes [https://www.atlassian.com/git/tutorials/what-is-version-control Click here] for an introduction to version control using Git This tutorial is a step by step guide to setting up an existing machine or diagnostic PC to a standard uses on all Stuga machines to enable quick, easy and stress free version control.standard uses on all Stuga machines to enable quick, easy and stress free version control.)
Installation Procedure - Autoflow Mk4 + (General Procedure is * Prepare Area * Unload from Transport * Locate and level infeed table * Locate, level and align machining module * Locate, level and align outfeed table * Fix to floor * Locate waste conveyor system * Guard fencing assembly)
Full Version Upgrade TwinCAT3 WinMulti + (If a PC fails on a machine in the field an … If a PC fails on a machine in the field and the hard drive data cannot be recovered, it is necessary to replace the PC. This may create a version conflict, as the new PC will have later versions of twinCAT installed than the original This tutorial outlines the steps required to bring all the machine systems up to the latest level to ensure compatibility

...This is a one-way process that cannot be reversed

ions-text">...This is a one-way process that cannot be reversed</div> </div> )
Ecoline - Disabling V axis To Swap Faulty Drive + (If a drive fails on an Ecoline, the V axis … If a drive fails on an Ecoline, the V axis can be utilised to enable the Ecoline to still run as a machining centre, albeit with V notching now disabled. This is a better situation than no machining at all, as all factories have V notching capability in addition to an Ecolineching capability in addition to an Ecoline)
Create a TwinCAT Project from Existing Project + (If you are confident and proficient in usi … If you are confident and proficient in using the Visual Studio editor to create TwinCAT projects, you can shortcut a lot of the data inputting by copying and modifying an existing project. This will keep the naming conventions and links exactly the same

...This should only be attempted if the machine has exactly the same EtherCAT box, drive and module setup

ne has exactly the same EtherCAT box, drive and module setup</div> </div> )
Commissioning - Off-Cut Laser Sensor + (Infeed Off-Cut Laser sensors are used to c … Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.be larger that the final triggered sensor.)
Ecoline Site Installation Guide + (Installation of an Ecoline is quite straig … Installation of an Ecoline is quite straight-forward as all of the main levelling and alignment is taken care of inside the main module housing. Installation involves 3 steps # Levelling main module # Attaching and Levelling Infeed Frame # Refitting Infeed coverling Infeed Frame # Refitting Infeed cover)
TB450 - CMOS Battery replacement + (Internal CMOS batteries are used in PCs to … Internal CMOS batteries are used in PCs to keep a constant power supply to BIOS memory while the main power supply is switched off. These batteries should last up to 5 years when a PC has been left idle. Sometimes these batteries can fall flat before this time either due to being low when sent out or extended use on older machines. The main symptom of a CMOS battery faulting on a Stuga machine is the PC not booting up when mains power is switched on which will be indicated by a “No Signal Detected” message being displayed on the screen. This is due to the BIOS setting “Restore AC Power Loss” going back to its default value of OFF due to the battery faulting. Restoring the BIOS to its original settings is a temporary fix in this situation as it is most likely this will happen again a couple of months down the line (See TB 376 or 213). The battery required is a '''CR2032'''. In the case of the Antec PC, and most commonly, the battery is held in an open housing that can be pushed to release and easily replaced. In PCs such as the Acer Revo the battery needs to be pre-wired with a plug but still easily unclipped and replacedug but still easily unclipped and replaced)
Stuertz Infeed - Check GY Position Parallelism + (It is important that the parallelism of th … It is important that the parallelism of the GY axis to the backfence is set and maintained along the length of the rack. This tutorial describes how to check this parallelism without the need for measuring equipment Potential Symptoms of a problem *Gripper cannot pick up offcuts *Gripper /profile end forced away from backfence *Accuracy problems *Gripper wobbles after it has released profile Use the laptop to enable you to control the Service screen whilst inside the infeed table

...You will be inside the danger area of the machine - ensure operators are aware of your situation

Ther gripper setting jig is used to give an accurate and reliable zero to locate the gripper jaw to. Any piece of aluminium reinforcing box section will also work Create a spreadsheet or a table to log your results,.
ng box section will also work Create a spreadsheet or a table to log your results,. )
R0000164 Spindle Disassemble for Required parts + (Obsoletion of main pcb tooling holder shaf … Obsoletion of main pcb tooling holder shaft has created inability to supply replacement spindle units that have failed on site. This procedure will extract required parts from failed units to provide a supply of parts required to create exchange units for R0000164 spindles
xchange units for R0000164 spindles )