Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

TB0383 Mint and RS Automation Drive Setup + (Take care of any physical gearboxes or gear trains you may have in your system these will need to be accounted for similar to the lead screw example)

VM Upgrade Software + ( # Install the VM Upgrade hardware [[VM Upgrade Hardware]] # Check that you have at lease 12GB of memory. # Check that the extra disk is present (Should be D) )
Updating Teamviewer Host + ( # Right click on the teamviewer icon in the taskbar (bottom right of screen) # Select Exit Teamviewer )
Upgrade ZX Machine to Beckhoff Drives and Control + (Before the upgrade is despatched to site, … Before the upgrade is despatched to site, the servo system needs to be assembled and pre-wired in its enclosure.
*Drill off Fan detail in right hand side of cabinet. A 114mm hole saw and arbor has been purchased for this. *Drill and fit 4 adjustable feet in the bottom of the cabinet. 4 extra nuts will be in the kit. The height of the feet does not need to be set at this stage. *Drill off all servo drives. For ZX3 machines, the rack will be as follows: AX8640-AX8118-AX8206-AX8206 and for a ZX4 the will be: AX8640-AX8118-AX8206-AX8206-AX8206 (the extra drive is for the V and W axes). *Pre-wire the rack (inc STO links) and the cabinet fan with the cable provided in the kit. leave the spare coil of cable in the cabinet ready for running on-site. *Plug in the 2x15m green etherCAT cables. *The enclosure bottom plate is left off to allow the cable entry on site. '''''*for detailed wiring information, please use drawing packs from Monday.com board.*'''''e use drawing packs from Monday.com board.*''''')
Setting Up Email Production Reports + (Navigate to Settings->Parameters)
Autoflow Power On + ((minimum 6 bar to machine))
ZX5 Installation Procedure + (No hard pipe under the Saw.)
Updating the Touchscreen Driver + ( * Go to Control Panel > Programs and F … * Go to Control Panel > Programs and Features > Uninstall a program * Scroll to 'EloMultiTouch' and click uninstall. Touchscreen will still work at this point as the Windows system takes over. However the new one still needs to be installed to allow for calibration. l needs to be installed to allow for calibration. )
Setting Up C0000422-KIT - Full Hardware 2023 + (Remove the PC from the Dell box with power adapter and power cable. Keyboard and mouse (if supplied) can be returned to stores (not needed here))
R0000204 Notching gear boxes assembly + (It is vital for correct function that all … It is vital for correct function that all the shown components are thoroughly degreased before assembly . To do this, wash all parts with FE10 solvent spray and dry with airline.

...Ensure your work area is very clean and free from Dust/swarf. Use a clean cloth or paper towel to lay on your bench to ensure parts remain clean once washed

o lay on your bench to ensure parts remain clean once washed</div> </div><br/>)
Zx5-Zx 4-Zx3-FL-S65 Saw Blade Removal and Refitting + (1 Open front door via control screen 2 Ensure emergency stop system is also activated for safe working 3 Remove swarf from saw)
TB0444 Renewing CF Card on TwinCAT2 Systems + (1. From Camera PC, use System Manager … 1. From Camera PC, use System Manager to activate original configuration 2. From Camera PC, use PLC Editor to login both original projects – PLC_Reset in Port 811, and the other main PLC control project in Port 801.

DO NOT FORGET TO ACTIVATE BOOT PROJECT

instructions-text">DO NOT FORGET TO ACTIVATE BOOT PROJECT</div> </div><br/>)
Ecoline - Setting V Notches on winMulti Software + (<div class="icon-instructions caution-i …

...Ensure that the ecoline is producing consistent and reliable datum test results

e ecoline is producing consistent and reliable datum test results</div> </div>)
WinMulti Shutdown procedure + (Once you have a black screen with a small blue text box in the middle you are safe to press the physical red 'POWER OFF' button on the console.)
Safety Circuit Principles +
Importing Picking List from Sage To Monday + (A pick run is a chunk or set of Job Cards that will be picked in a controlled amount. This is normally 10-20 job cards. it is managed in this way to keep the amount of time between the allocation on Sage and the physical pick as short as possible.)
Guide to Fitting Eject Push Sensors on ZX Machines + (A retrofit kit will be sent with all the p … A retrofit kit will be sent with all the parts needed to carry out this task. The assembly number for the kit is R0019218. If you have any feedback regarding this kit, please use this assembly number. It is important to check the parts you have received against the assembly list to ensure you have nothing missing before starting the job.e nothing missing before starting the job.)
R0000712E Rotary Trunking + (All bolts must have Loctite 243 adhesive applied unless otherwise stated. All bolts must be marked with pen once completed to indicate adhesive and correct tension has been applied)
R0015064 Bench Assemble Clamp Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015064 Bench Assemble Clamp Assembly Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015037 Bench Assemble SY Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305 Install Wiring loom for Rotary loom + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R0000299 Stroke assembly rebuild Part 2 + (Always use Loctite 243 on all fasteners fitted unless stated different All bearings should be an acceptable fit, with Loctite 641 and FE10 solvent used if required All fasteners should be marked once finalised)
Upgrading Project File on TwinCAT2 System + (Check the [https://stugaltd.monday.com/boards/304269981 Control Systems Log] board to look up the machine and the control system used This procedure only applies to TwinCAT2 For TwinCAT3 upgrades use [[Full Version Upgrade TwinCAT3 WinMulti]])
TB0409 Setting Up Windows 10 PC 2018 + (Connect monitor, network cable, keyboard, mouse/touchpad, and switch on PC.)
Repairing R axis datum pin + (Drill a 2.5mm hole in the datum pin shoulder. Refit to datum plate and use the drilled hole as a guide to drill the aluminium spindle plate. Remove datum pin and tap the hole in the plate using the M3 tap.)
R0000164 Spindle Build + (Ensure all parts supplied are visually che … Ensure all parts supplied are visually checked for damage such as burs or surface contamination Report any issues to supervisor D0006016 may be issued with surface rust . This should be cleaned with green scotchbrite pads as shown in photos to remove contaminationas shown in photos to remove contamination)
CX5120 Replacement + (Ensure replacement CX5120 is setup using [[TB0451 CX5120 Beckhoff PC Setup|https://stuga.dokit.app/wiki/TB0451_CX5120_Beckhoff_PC_Setup]] before sending to site)
Autocut Startup Procedure + (Ensure the main isolator on the console is in the on position (pointing up).)
ZX5 Transfer Table Setup + (The rollers on top are mounted on eccentri … The rollers on top are mounted on eccentric bushes. We only need these just tight enough to not allow any slop or vertical play. Slacken the cams off completelely, you will need an 8mm spanner with the faces ground down to fit in the space. Slide the plate onto the rail and tighten the eccentric bushes until any vertical play is removed. Lightly try to move the assembly on the X axis, if there is any slop then it needs to be a little tighter but probably no more than an 1/8th of a turn. Once set you should still be able to spin the rollers by hand, but still feel a fair bit of resistance. Once set slide the assembly over the full length of the V rails to check fo any tight spots. If there are then you need to check that the two halves of the fail are fully mated!!! two halves of the fail are fully mated!!!)
Autocut Adding New Profile + (Firstly, we need to make sure that the pro … Firstly, we need to make sure that the profile will physically go through the machine, open the top gaurd door. Ideally, you will have a 1 metre offcut of the profile - work out the best way for the profile to go through the machine. Push the profile through the machine by hand to ensure no catching areas etc.e by hand to ensure no catching areas etc.)
TB0422 Commissioning ZX5 Software 2018 + (Follow [https://stuga.dokit.app/wiki/TB0409_Setting_Up_Windows_10_PC_2018 technical bulletin 409] to setup PC with correct naming conventions and TeamViewer.)
TB0425 Lenovo Tablet Setup + (Go to the PlayStore and download the e-Drawings app. This will cost (currently £1.25) therefore ask appropriate member for a company card.)
ZX5 Installation Procedure 2023 + (Identify if either saw infeed or multi head outfeed is the logical frame to place first . Consider access to machine when installing 1st frame Consider handing of machine)
R0015280 Module E Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed * Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testinglies are at a sufficient stage for testing)
PC Bios Power settings + (Keep pressing the “DELETE “button on the k … Keep pressing the “DELETE “button on the keyboard until the PC goes into the BIOS mode and you see a screen similar to the ones shown below. If the BIOS screen does not show wait for the PC to LOGIN into windows and then shut-down or restart the PC again and retry using the delete button as described above. The Menu Will look something similar to thise Menu Will look something similar to this)
Updating Baldor ESB Firmware 2022 + (Located in the dropbox folder D:\Dropbox (Stuga Machinery Ltd)\service\3rd Party Manuals\Servos\Baldor)
R0015307 Bench assembly spindle drive cylinders + (8 off P0001200 cylinder Use Loctite 572 on all air fittings 1 Attach P0001098 elbow as shown 2 Attach P0001198 elbow 3 Attach P0000238 elbow <br/>)
Changing Main Saw Blade + (Make sure you have stopped cutting and nothing on the machine is moving - press an emergency stop button to ensure this.)
C0001005MM Micromech Stepper Motor Assembly + (Mark the motor face as the picture to give … Mark the motor face as the picture to give the correct mounting position A 3mm hole must be drilled in this position at a depth of 5mm . Caution, damage can be caused to motor if this depth is not adhered to. Increase drill sizes incrementally when drilling, to ensure a good sized 3mm hole Use masking tape to stop swarf entering the stepper motor housing Use a drop of Loctite 270 to ensure dowel remains in place when fitted ensure dowel remains in place when fitted)
Install markings and measurements ZX5 + (Measure and mark up the distance between t … Measure and mark up the distance between two points (one on each) of the two modules. Mark up the points in a place where it is easy to read the markings and simply practical to get the two modules in a similar position (gap between the two) on installation - preferably on the front and the back of the modules. This makes it easier and closer to adjusting the loadpos and datum on the x-axis once setting up accuracy.um on the x-axis once setting up accuracy.)
R0015276 Line up slider units and mesh racks + (1 Slide drive pinion into position 1 under … 1 Slide drive pinion into position 1 under drive rack 2 Use M4 adjuster screws to adjust height of rack and M6 to secure 3 Slide out drive pinion and move rack to position 2. Refit drive pinion 4 Use M4 adjuster screws to adjust height of rack and M6 to secure 5 Repeat steps until correct meshing is present at all points indicated to check Do Not glue any of the M4 /M6 socket caps used for adjustment as this will be done at a later stagement as this will be done at a later stage)
500mm Saw Blade Upgrade + (Remove the two grub screws from the taper … Remove the two grub screws from the taper lock pulleys and insert one into the hole that was initially empty. Screw in tight to break seal of taperlock and split the two parts. If siezed the outer part can be tapped back with a hammer. These parts are usually very brittle and can shatter with a heavy hammer blow. It can also be useful to have the belts on at this point to stop the pulley from turning.his point to stop the pulley from turning.)
Stuertz Infeed - Align and dowel GX rack + (Using the T0001090 alignment tool, check each 1m section of the rack is aligned to its neighbour <br/>)
Updating Beckhoff TwinCAT3 Backend Version + (On the desktop of the Beckhoff PC, right c … On the desktop of the Beckhoff PC, right click the Twincat Icon in the taskbar and select "About Twincat..." TwinCAT version is displayed. 3.4024.xx is needed

...The .xx is the build number. Generally, all .xx will be compatible, they release a new build number for bug fixes but will change the main version number when it becomes incompatible

change the main version number when it becomes incompatible</div> </div><br/>)
Easily resizable forms for any screen resolution in Visual Studio + (On the start screen in Visual Studio, click on the "Create a New Project" button.)
TB0426 Replacement Zebra Printer Setup + (Open box, unwrap printer, plug in power and plug Ethernet connected to network to the printer. As the printer boots up there will be a red light displayed on the front. After around 30 seconds this will turn green as the printer completes boot up.)
R0015336 Pneumatic Output Testing +
Training Laser on Ecoline + (Place a clean, white profile or sheet of paper in the clamps and adjust the Y axis position so the laser dot can be seen below it Focus the laser to make the dot as small as possible on the base of the profile)
Changing Pneumax Valve slice + (Please ensure screwdriver is a good fit to avoid wearing the head of the screw.)
R0000088E Stage 1 Spindle assemble + (Linear rail B0000045 needs fitting to each … Linear rail B0000045 needs fitting to each spindle base

..Linear rails have a datum face indication. Attention must be paid for correct orientation

1 Orientation of Datum face is as shown Ensure all linear rails and machined grooves in spindle plates are free from debris. Use compressed air. 2 Insert linear rail into each spindle base and drop in m6 x 20 socket caps with adhesive applied into all rail counterbores, do not screw innd drop in m6 x 20 socket caps with adhesive applied into all rail counterbores, do not screw in)
Programming Eaton DE Drive + (Set these references P-20 to P-23 to 50Hz so it will not matter what input 3 or 4 is set to - it will always be 50Hz)
R0000728 R0000729 Stroke Assembly Dismantling + (The stroke assembly must be dismantled in the exact manner stated as many sections can only be removed once mating parts have been extracted Please use the following steps accurately)
R0000299 Stroke assembly rebuild + (R0000728 and R0000729 are mirror images to each other Please inspect pictures to clarify and confirm correct hand to be built (Supplied unit to be refurbished will always be rebuilt as the same hand ))
Upgrade - Gripper Slider Mechanism + (Remove all existing parts, including the profile lever, slideway and bearings, and the spring. Install new stronger slideway)
TB450 - CMOS Battery replacement + (Remove cover by taking out the circled screw. Then holding the tab, pull in the direct shown to unclip and remove the cover.)
R0000711 Rotary Base Assembly REV2 + (Rotary drive ring needs checking before f … Rotary drive ring needs checking before fitment.
#Check teeth for burrs, damage and debris. Use compressed air to clean all areas #V edge should be checked for damage. Check entire circumference with fingers to identify any damage, lumps or high low spots #Check drive ring has been countersunk in the shown arearive ring has been countersunk in the shown area)
Client Installation of Sage and Cim50 + (Navigate to \\mainserver\Cim50\Updates)
Replacing Beckhoff PC + (Take care to ensure all cables are replaced in the same relative positions Power on)
Laser Setup on Flowline/ZX3 for Laser Holes + (The laser sender needs to have a clear pat … The laser sender needs to have a clear path to the laser receiver, its really important that this is parallel and the beam does not bounce off the inside of any of the aluminium mounting block. Slacken off the Nuts above and below Laser to move up/down and side/side.below Laser to move up/down and side/side.)
Saje uPVC Unloading Process + (Including the chop saw table Leaving a clear route for the 2.4m x 7.5m table to roll in)
Create a TwinCAT Project from Existing Project + (The build needs to be the same machine typ … The build needs to be the same machine type and have an identical EtherCAT box and drive setup You can create a backup in three ways # Create an archive of an open project (you need to run Visual Studio on the desktop of the machine in question) # Copy the contents of the c:\TwinCAT\Stuga\[BuildNo] folder from the "donor" to your new machine setup # Use VPN to connect to the back end of the machine and upload the project from the target, then save it locally. this needs a good internet connection and Teamviewer remote VPN installed on the remote Beckhoff PCte VPN installed on the remote Beckhoff PC)
Dokit - Creating A Work Instruction + (To create a new Dokit, you need to login as a editor The Username is Gareth Green Password is available from the IT department <br/>)
Dokit - Editing Work Instructions + (The dokit references for work instructions … The dokit references for work instructions are tracked and stored on the monday board [https://stugaltd.monday.com/boards/3628350043 Work Instruction Dokit Tracker] Check to see if the instruction is already there using the search, there should be a link for it in the link column which will take you straight to the page. If it does not exist, it needs to be created first with this tutorial [[Dokit - Creating A Work Instruction]][[Dokit - Creating A Work Instruction]])
Beckhoff AX8000 Flowline Upgrade + (The first step does not involve being on s … The first step does not involve being on site or carrying out any physical tasks. However, trying to gain some familiarisation before carrying out the upgrade can save time and confusion down the line. Please read through this tutorial before upgrading the machine. The attached files and steps will walk you through the upgrade that somebody else has already experienced. This will give you a free look at any issues or learnings that have already been made. or learnings that have already been made.)
Toshiba - B-EX4T1 Printer Setup + (To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up.)
TB0447 ZX5 Setup - X Axis Beam Calibration + (The out and home sensors must be adjusted … The out and home sensors must be adjusted so that the "just" come on at the end of the stroke.

...This is important because the physical end stop position will directly affect the positional accuracy. If the end stop is not reached by as little as 0.5mm, the end stop sensor should be the fail-safe to ensure the machine stops with an alarm.

be the fail-safe to ensure the machine stops with an alarm.</div> </div><br/>)
ZX5 Transfer Table Crank set up +
Fitting R0019199 Upgrade: Autoflow Slewing Ring Guard Kit + (This procedure must be done in conjunction with moving the SR Axis Datum to a position higher and ant the front of the machine to [[Move SR Datum Sensor to Higher Level R0019217]] <br/>)
R0000971E Bench Assemble R Axis Gearbox +
R0015011 Bench assemble Gripper + (check shafts fit correctly into bores of D0015082 gripper bottom bar and D0015083 gripper upper bar)
R0015303 Fit backplates and covers + (Use Loctite 243 on all fasteners Pen mark all bolts to show finalised)
R0015004 Bench Assemble Gripper + (1 Fit bushes B0001106 (20 off) to 8 off D0015095 link bars 2 off D0015096 link bars 2 Fit bearings B0000034 x 2 into D00015086 grip slide body. Use grease to lubricate bearing before assembly)
Autoflow Maintenance - Infeed + (Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds)
R0015063 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000962E Bench assemble Y axis Components +
R0000963E Bench Assemble Z axis Components +
R0015090 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015274 Fit X Axis Gearbox and Motor + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
VM Upgrade Hardware + (With the machine turned off , find the FE PC and remove it as much as you need to gain access to the top cover. If you are upgrading the memory try and remove the PC to a flat surface.)
Convert TC2 Project to TC3 + ( #Open Visual Studio #Create a new TC3 pro … #Open Visual Studio #Create a new TC3 project called [BuildNo] in c:\TwinCAT\Stuga\ #Make sure "Create Directory..." is Unticked #Right Click on the project name and select ‘Load Project from TwinCAT 2.11 Version…’ #Click Cancel on the two windows asking to convert the PLC project #Ignore or cancel any warnings about libraries (this part will be replaced later)

...Once created, you will have a copy of all the devices and boxes in the project with the correct naming.

f all the devices and boxes in the project with the correct naming.</div> </div><br/> )
Stuga Product Database - Edit Product Data + (Search box is upper right)