Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

R0015146 Pneumatic pipe Installation + (1 Cut 6 lengths of 6mm black pipe at 5 meter long . 2 Use cables EC06F and 25F from loom box)

TM018B Microline and ZX3 V Notch Blade Setup + (A calibration mnd file has been written to … A calibration mnd file has been written to help line up the x offsets called VTEST. This program creates the following pattern on the bottom of the profile using a 10mm spindle and the notching blades themselves: Run the VTest operation on a length of large outer frame of at least 1m long. Put the operation at a position of 500mm. The pattern allows you to measure the offsets required with calipers.

...Profile is viewed from the bottom face, Basically turn it over when it comes of the transfer table.

face, Basically turn it over when it comes of the transfer table.</div> </div><br/>)
Upgrade ZX Machine to Beckhoff Drives and Control + (Before the upgrade is despatched to site, … Before the upgrade is despatched to site, the servo system needs to be assembled and pre-wired in its enclosure.
*Drill off Fan detail in right hand side of cabinet. A 114mm hole saw and arbor has been purchased for this. *Drill and fit 4 adjustable feet in the bottom of the cabinet. 4 extra nuts will be in the kit. The height of the feet does not need to be set at this stage. *Drill off all servo drives. For ZX3 machines, the rack will be as follows: AX8640-AX8118-AX8206-AX8206 and for a ZX4 the will be: AX8640-AX8118-AX8206-AX8206-AX8206 (the extra drive is for the V and W axes). *Pre-wire the rack (inc STO links) and the cabinet fan with the cable provided in the kit. leave the spare coil of cable in the cabinet ready for running on-site. *Plug in the 2x15m green etherCAT cables. *The enclosure bottom plate is left off to allow the cable entry on site. '''''*for detailed wiring information, please use drawing packs from Monday.com board.*'''''e use drawing packs from Monday.com board.*''''')
ZX5 Installation Procedure + (No hard pipe under the Saw.)
ZX5 Alignment Check + ( * Check backfence roller alignment to infeed * Check roller heights to infeed and outfeed )
Setting Up C0000422-KIT - Full Hardware 2023 + (Remove the PC from the Dell box with power adapter and power cable. Keyboard and mouse (if supplied) can be returned to stores (not needed here))
Decommissioning - Autoflow Mk4 1 + (Ensure the plugs are labelled <br/>)
WinMulti Shutdown procedure + (Once you have a black screen with a small blue text box in the middle you are safe to press the physical red 'POWER OFF' button on the console.)
Ecoline - Setting V Notches on winMulti Software + (<div class="icon-instructions caution-i …

...Ensure that the ecoline is producing consistent and reliable datum test results

e ecoline is producing consistent and reliable datum test results</div> </div>)
Correcting Linearity with Rack Offset File + (Write the error +\- next to each notch, me … Write the error +\- next to each notch, measuring from machining centre end (photo shown is RtoL feed machine). Repeat for each notch on each of the 3 bars Again, check for consistency. If there is any doubt that the results have not repeated consistently 3 times, then do not proceed consistently 3 times, then do not proceed)
Guide to Fitting Eject Push Sensors on ZX Machines + (A retrofit kit will be sent with all the p … A retrofit kit will be sent with all the parts needed to carry out this task. The assembly number for the kit is R0019218. If you have any feedback regarding this kit, please use this assembly number. It is important to check the parts you have received against the assembly list to ensure you have nothing missing before starting the job.e nothing missing before starting the job.)
R0000712E Rotary Trunking + (All bolts must have Loctite 243 adhesive applied unless otherwise stated. All bolts must be marked with pen once completed to indicate adhesive and correct tension has been applied)
R0000712F Rotary Trunking + (All bolts must have Loctite 243 adhesive applied unless otherwise stated. All bolts must be marked with pen once completed to indicate adhesive and correct tension has been applied)
R0015146 Pneumatic pipe Installation Part 3 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0000558E Bench Assemble Base and Turntable Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R000569E Bench Assemble Head Spindle Posts + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015066 Bench Assemble Saw Motor Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015037 Bench Assemble SY Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015335 Mount Electrical Cabinet + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015041 Bench Assemble Top Hood Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305 Install Wiring loom for Rotary loom + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R000562 Bench Assemble Centralise Top Table + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation Part 3 +
R0000558E Bench Assemble Base and Turntable + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015333 Fit Clamp Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015146 Pneumatic pipe Installation + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305A Install Wiring loom for Rotary Ring + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R0015087 Pneumatic Connections + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015146 Pneumatic pipe Installation Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015100 Fit Guarding + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015326 Bench Assemble Roller Backfences + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
ZX5 Installation Procedure 2023 Pneumatic connections + (All control pneumatic connections will be … All control pneumatic connections will be identified with identification numbers All permanently fed supply lines will be identified by the use of Red pneumatic pipe All Emergency stop switched air feeds will be identified by the use of Blue pneumatic pipeentified by the use of Blue pneumatic pipe)
R0015300 Rotary Ring pneumatic test + (When air is connect to rotary ring, attention should be paid to any audible air leaks. If any are present, identify source and rectify)
Setting up an Ecoline Barcode Scanner + (All refurbished Ecolines will now be provi … All refurbished Ecolines will now be provided with USB barcode scanners. This may be a hand held device or an 'Orbital' scanner attached to the infeed table depending on the customer's preference. Use the provided cable to plug the scanner in to the nearest available USB port. There will be 2 USB extension cables coming from the PC inside the cabinet. One will go to the console to control the keyboard and the touchscreen and the other will go to the infeed table junction box to control one or two barcode scanners.ox to control one or two barcode scanners.)
ZX5 Production R0000548E Module G to R0015040 Module F alignment +
Upgrading Visual Studio to Beckhoff TCXAEShell + (Ask one of the IT team to connect and down … Ask one of the IT team to connect and download it

...It is over 1Gb long!

G:\Design\TwinCAT3\TC31-FULL-Setup.3.1.4024.22.exe
er 1Gb long!</div> </div> G:\Design\TwinCAT3\TC31-FULL-Setup.3.1.4024.22.exe <br/>)
R0015382 Top Spindle Blower Upgrade + (Assemble Valve and Y connector as shown)
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Before installing module B, module C rolle … Before installing module B, module C roller tables should be double checked for correct positioning 1 To do this inspect tables 1, 2,3 and 4 for level as shown. 2 Also inspect alignment with 2 meter straight edge. All rollers should be on the same height and no bump up should be present when moving the straight edge over the table. 3 Ensure fixed table is at same height as rollers Report any discrepancies to supervisor for correct remedial action to supervisor for correct remedial action)
R0015295 Finalise wiring loom for Rotary head + (Cables must be adjusted between each spind … Cables must be adjusted between each spindle to ensure the cable lengths are correct . 1 Start at cable point between 6 and 5 . Start with the light green ethercat cable with the right angle plug. Adjust so that 200mm is past the end of the spindle plate . See picture for detail. 2 Move to the next spindle connection between 5 and 4 and adjust the new right angled ethercat cable to match the length of the previous adjusted cable 3 Repeat this process working your way around the spindles to set all ethercat cablesnd the spindles to set all ethercat cables)
ZX5 Installation Procedure 2023 Part 2 + (Check X axis alignment of horiczontal and … Check X axis alignment of horiczontal and vertical rollers using 2 meter straight edge and feeler gauges Any discrepancy must be reported and rectified if present Tolerance 0.002" / 0.05mm [https://stugaltd.monday.com/boards/3628350043/pulses/4665028475][[R0015311 Install and Align Datum rollers]]
[[R0015311 Install and Align Datum rollers]] <br/>)
Removing or changing a Beckhoff AX8000 series servo drive + (Circuit breaker will be labelled 'Servo Drives')
R0015327 Level Frame and quality Check + (Clean all threads in frame using standard taps)
R0015033B ZX5 Module F Wiring Loom + (Connect ethercat power cables)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Position module F at end of Module E infeed frame Approximately Align Saw roller back fences to Saw infeed back fences Approximately align X axis position by setting the to frames spaced at the distance shown of 20mm)
R0015284 Frame ancillaries + (Fit 5 off basket support bracket to pre drilled holes at indicated points . Secure using M8 x 20 socket caps and Large M8 washers)
Ecoline - Datum and MitreOffset Tests + (Cut 3 lengths of outerframe around 1000mm … Cut 3 lengths of outerframe around 1000mm long

...Make sure the gripper end of the profile has a clean edge - ie no swarf and profile tape is not "flapping" over the end

ie no swarf and profile tape is not "flapping" over the end</div> </div><br/>)
R0000164 Spindle Build + (Ensure all parts supplied are visually che … Ensure all parts supplied are visually checked for damage such as burs or surface contamination Report any issues to supervisor D0006016 may be issued with surface rust . This should be cleaned with green scotchbrite pads as shown in photos to remove contaminationas shown in photos to remove contamination)
ZX5 Transfer Table Setup + (The rollers on top are mounted on eccentri … The rollers on top are mounted on eccentric bushes. We only need these just tight enough to not allow any slop or vertical play. Slacken the cams off completelely, you will need an 8mm spanner with the faces ground down to fit in the space. Slide the plate onto the rail and tighten the eccentric bushes until any vertical play is removed. Lightly try to move the assembly on the X axis, if there is any slop then it needs to be a little tighter but probably no more than an 1/8th of a turn. Once set you should still be able to spin the rollers by hand, but still feel a fair bit of resistance. Once set slide the assembly over the full length of the V rails to check fo any tight spots. If there are then you need to check that the two halves of the fail are fully mated!!! two halves of the fail are fully mated!!!)
AX8000 Drives - ES Contactor Wiring + (Find a spare section of DIN rail that the contactor can be placed in. The contactor clips onto the din rail without the need for fixings.)
ZX5 Installation Procedure 2023 + (Identify if either saw infeed or multi head outfeed is the logical frame to place first . Consider access to machine when installing 1st frame Consider handing of machine)
R0015280 Module E Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed * Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testinglies are at a sufficient stage for testing)
Fitting M8 Plug for EtherCAT Boxes + (Inside the packet of the plug will be 5 co … Inside the packet of the plug will be 5 components: 1- Metal outer shell 2- Numbered insert 3- m8 IDC connector 4- Individual 'white' grommet 5- Additional 3 grommets

...The 'white' grommet and numbered insert may be stuck in the metal shell. Please check!

Make sure you check that you have all of these parts before disposing of the packaging.gt;Make sure you check that you have all of these parts before disposing of the packaging.)
Flowline 6 to 6o5m Extension + (Clean and remove any dirt/grease/imperfections on the box section ready the the new rails. If any of the tapped holes are compromised, re-tap 6mm.)
ZX5 Gripper Energy Chain & Tray Setup + (Make sure the cables and piped are fixed with cable ties to the fingers of the bracket to avoid movement or twisting inside the energy chain.)
R0015276 Line up slider units and mesh racks + (1 Slide drive pinion into position 1 under … 1 Slide drive pinion into position 1 under drive rack 2 Use M4 adjuster screws to adjust height of rack and M6 to secure 3 Slide out drive pinion and move rack to position 2. Refit drive pinion 4 Use M4 adjuster screws to adjust height of rack and M6 to secure 5 Repeat steps until correct meshing is present at all points indicated to check Do Not glue any of the M4 /M6 socket caps used for adjustment as this will be done at a later stagement as this will be done at a later stage)
500mm Saw Blade Upgrade + (Remove the two grub screws from the taper … Remove the two grub screws from the taper lock pulleys and insert one into the hole that was initially empty. Screw in tight to break seal of taperlock and split the two parts. If siezed the outer part can be tapped back with a hammer. These parts are usually very brittle and can shatter with a heavy hammer blow. It can also be useful to have the belts on at this point to stop the pulley from turning.his point to stop the pulley from turning.)
TB0452 ZD620 Zebra Printer Setup + (One difference between the GX420d and the … One difference between the GX420d and the ZD620d is the lack of a dedicated power switch. The newer ZD620d opts for a power button that must be pressed in order to turn on the printer after power is supplied. As our machines are fully un-powered after a machine is closed down it causes the operator to intervene and manually turn on the printer after power up. Ideally the Zebra ZD620d has an '''Power Recovery Mode''' that acts as a permanent switch in case of power failure. We can use this on the machines to allow the printer to turn on upon power up. 1. Disconnect from power. 2. Remove module door and use Ethernet cable to remove (plug in and pull). 3. Move the switch that is annotated AUTO to the ON position. 4. Reinstall the module. 5. Reconnect power, this should now turn on. Reconnect power, this should now turn on.)
R0015336 Pneumatic Output Testing +
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Position module A in front of module B Use Infeed back fence to Multi head datum rollers as initial alignment guide for Y axis Set gap of 23mm -+ 2mm between module A roller frame and module B roller block)
Flowline Turret Upgrade - Somatec + (Remove all parts from the existing turret, to leave just the mounting plate and the cylinder and fittings etc, as shown)
R0010309 Ecoline Ultrasonic Material Loaded Upgrade + (Remove old material load assembly from mac … Remove old material load assembly from machine. Held on by 2 off M6 socket caps indicated 2 Disconnect switch/sensor. Depending on variant fitted either Unscrew M8 plug connection to disconnect for sensor style Or Disconnect 2 off fork connections onto rear on switch 3 Disconnect bloweronto rear on switch 3 Disconnect blower)
Replacing Beckhoff PC + (Take care to ensure all cables are replaced in the same relative positions Power on)
R0015243 ZX5 module A-C-E Frame levelling +
Saje uPVC Unloading Process + (Including the chop saw table Leaving a clear route for the 2.4m x 7.5m table to roll in)
Dokit - Creating A Work Instruction + (To create a new Dokit, you need to login as a editor The Username is Gareth Green Password is available from the IT department <br/>)
Beckhoff AX8000 Flowline Upgrade + (The first step does not involve being on s … The first step does not involve being on site or carrying out any physical tasks. However, trying to gain some familiarisation before carrying out the upgrade can save time and confusion down the line. Please read through this tutorial before upgrading the machine. The attached files and steps will walk you through the upgrade that somebody else has already experienced. This will give you a free look at any issues or learnings that have already been made. or learnings that have already been made.)
Toshiba - B-EX4T1 Printer Setup + (To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up.)
Hotswap Beckhoff PLC with Licence Slice Installed + (There are a row of retaining clips on bot the top and bottom of the PC that hold it to the Din rail. Pop them open with a flathead screwdriver)
ZX5 Transfer Table Crank set up + (Follow the instructions in [[Programming Eaton DE Drive|this]] … Follow the instructions in [[Programming Eaton DE Drive|this]] tutorial.

...It is vital that the Eaton drives are programmed correctly as the distance the cranks travel and the time they take to stop depend on the acceleration and deceleration of the drive.

...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.

xt">...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.</div> </div><br/>)
Fitting R0019199 Upgrade: Autoflow Slewing Ring Guard Kit + (This procedure must be done in conjunction with moving the SR Axis Datum to a position higher and ant the front of the machine to [[Move SR Datum Sensor to Higher Level R0019217]] <br/>)
R0015251 Bench Assemble X Axis components and Energy chain + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015140 Spindle energy chains and looms + (Use Loctite 243 on all fasteners Pen mark bolts once finalised)
R0015286 Bench Assemble X axis Components and Energy Chain + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015299 Install Spindle control pipework and fittings + (Use Loctite 243 on all fasteners Pen mark all fasteners to show finalised)
R0015301 Fit terminal holders and Ethercat boxes + (1 Segregate cables and pipes as shown in image 2 Mount D0010806 relay mounting base using 4 off M3x 25 pan head screws 3 Repeat for 7 off other connection boxes)
R0015294 Fitment of wire basket and feed pipes +
R0015272 1st Stage fitting Saw Outfeed + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0015348 Fit Flexible Ducting + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015096 (e) Bench Assemble Transfer Drive Assembly + (Use Loctite 243 on all fasteners Use Loctite 572 on all pneumatic threaded connections Pen mark all bolts to show finalised)
J0001000H Autoflow Mk4 Mechanical installation-Alignment + (Use footprint drawing to determine machine location for installation)
R0015090 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015332 Mount Backfences and Align + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015063 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000962E Bench assemble Y axis Components +
R0000963E Bench Assemble Z axis Components +
R0015273 Module E support arm alignment + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015324 Install pipe and cable looms + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015271 Mount buffer bars +
R0015290 Bench Assemble Top guard + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
VM Upgrade Hardware + (With the machine turned off , find the FE PC and remove it as much as you need to gain access to the top cover. If you are upgrading the memory try and remove the PC to a flat surface.)
Z Transom Width Measurement + (A straight faced piece of profile the same height as the Z section or taller or a piece of steel straight edge or the like; then lastly a Z section profile for measuring.)
Fitting Zx5 Crank Upgrade + (B0001166)
R0015278 Mount Completed Assemblies Section two + (these steps follow on from dokit [[R0015278 Mount Completed Assemblies]])