Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.
Liste de résultats
- Setting Gripper Nose + (It is very important to ensure the gripper nose and heel is correctly set up. This assembly is subject to a lot of wear and tear and maintenance is very important. Incorrect setting or play in this assembly is a major cause of accuracy issues)
- R0015114 Bench Assemble Valve Banks and Regulators + (<nowiki>'''<u>Tools Required&l …
'''Tools Required''' <br />P0001071 Valve base type41 8 position x 1<br /><br />P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4<br /><br />P0001101 Male straight 1/4 bsp to 12mm x 2<br /><br />P0001102 Fitting male elbow 12mm 1/4 x 4<br /><br />P0001105 Bulkhead straight 12mm x 6<br /><br />P0001186 Valve. 24v dc smc x 8<br /><br /><br/></nowiki>)
Standard hex key set
Standard spanner set
Standard HSS drill set
Standard tap set
'''Parts Required'''
H0007998 Regulator internal mount 5 way x 1
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14
P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9
P0000021 air gun assembly x 1
P0000024 hex nipple 1/4 x 3
P0000058 Regulator Mounting Kit x 1
P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2
P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2
P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2
P0000145 tee equal 1/4 x 3
P0000159 Fitting: Stem Blanking Plug 6mm x 2
P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1
P0000278 Regulator 0-2 bar x 1
P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8
P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1
P0000419 Air Service Unit OH (P0283) x 1
P0001071 Valve base type41 8 position x 1
P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4
P0001101 Male straight 1/4 bsp to 12mm x 2
P0001102 Fitting male elbow 12mm 1/4 x 4
P0001105 Bulkhead straight 12mm x 6
P0001186 Valve. 24v dc smc x 8 - Autoflow Maintenance - Gripper + (<nowiki>The following preventative m …
The following preventative maintenance tasks should be carried out regularly on the machine. The frequency depends on the machine use, but as a guide: i-Weekly<br />20 Hrs/Week Monthly</pre></div></nowiki>)2-3 Shifts Weekly
40 Hrs/Week Bi-Weekly
20 Hrs/Week Monthly - Autoflow Maintenance - Infeed + (<nowiki>The following preventative m …
The following preventative maintenance tasks should be carried out regularly on the machine. The frequency depends on the machine use, but as a guide: kly<br />20 Hrs/Week Monthly</pre></div><br/></nowiki>)2-3 Shifts Weekly
40 Hrs/Week Bi-Weekly
20 Hrs/Week Monthly - R0015034B ZX5 Module B Wiring Loom installation Part 3 + ('''<u>Parts Required</u>''' Pre labelled Wiring loom assembly R0015034B from electrical team '''<u>Tools required</u>''' Flush cutters Tie wraps small Tie Wraps Large)
- R0015034B ZX5 Module B Wiring Loom installation + ('''<u>Parts Required</u>''' Pre labelled Wiring loom assembly R0015034B from electrical team '''<u>Tools required</u>''' Flush cutters Tie wraps small Tie Wraps Large <br/>)
- R0015034B ZX5 Module B Wiring Loom installation Part 2 + ('''<u>Parts Required</u>''' Pre labelled Wiring loom assembly R0015034B from electrical team '''<u>Tools required</u>''' Flush cutters Tie wraps small Tie Wraps Large)
- R0015266B mount completed assemblies + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard hex key set '''Parts Required''' D0015432 Spacer: Ø25.4 x 100mm (12.7mm ID) x 10 D0015479 Sensor Mount Rail 1450 mm Long x 4 D0015480 Sensor Mount Rail 825 Long x 1 F0000299 T Nut Sub Insert M6 (Fat) x 16 R0015074 Pre assembled keyboard mount and buttons R0015030B Bench Assembly Loader Wheel R0015080 Bench assemble sensor rail R0015271 Mount buffer bars ( pre fitted to frame ) R0015351 Mount monitor to frame (pre fitted to frame) to frame ) R0015351 Mount monitor to frame (pre fitted to frame))
- R0015278 Mount Completed Assemblies + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard Hex key set
Standard spanner set
300 mm rule
1000mm rule
'''Parts Required'''
D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1
D0015583 Take Up Beam Joiner x 1
D0015598 Datum Flag: Saw Infeed x 1
D0015717 Energy Chain Angle Bracket Lower x 5
D0015718 Energy Chain Angle Bracket Upper x 5
D0015720 Carriage Bracket x 1
D0015721 Energy Chain Tray Deep Long x 1
D0015723 Energy Chain Tray Shallow x 1
D0015724 Energy Chain Tray Deep x 1
D0015725 Energy Chain Tray Shallow Medium x 1
D0015742 Takeup Pad Right ZX5 x 1
E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1
R0015011 Bench Assemble Gripper
R0015063 Bench Assemble Roller Tables
R0015096 Bench Assemble Transfer Drive Assembly
R0015101 Bench assembly take up assembly
R0015286 Bench Assemble X axis components and energy chain
R0015286 Bench Assemble X axis components and energy chain <br/>) - R0015030B Bench assemble loader wheel + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard hex keys Standard spanner set Cutting blade Rule External circlip pliers Switch setting box Ball pien hammer '''Parts Required''' D0015438 x 1 D0010431 x1 B0000426 x 1 B0000173 x 7 D0010238 x 1 B0000046 x 2 D0015741 x 1 D0015439 x 1 M0001077 x 1 D0010509 x 1 D0015436 x 1 D0010611 x 1 P0001044 x 1 P0001098 x 1 P000001174 x 1 P0000200 x 1 P0001198 x 1 P0001047 x 1 P0001041 x 1 P0001042 x 1 B0000240 x 1 B0001100 x 2 D0015435 x 1 B0000053 x 1.2 B0000054 x 2 D0015434 x 1 B0000189 x 1 B0000142 x 1053 x 1.2 B0000054 x 2 D0015434 x 1 B0000189 x 1 B0000142 x 1)
- R0015278 Mount Completed Assemblies Section two + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chainsembly R0015286 Bench Assemble X axis components and energy chain)
- R0015264 Fit Loader chains to arms + ('''<u>Tools Required</u>''' Standard hex key set Standard spanner set 150mm rule Long nose pliers Loctite 290 Straight ended 4mm hex key and extension bar '''<u>Parts Required</u>''' Pre assembled R0000699 9off loader chains)
- R0015331 Mount Centralise Assembly + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard spanner set
Steel rule 600mm
Soft hammer
'''Parts Required'''
D0004672 Centralise Sensor Bracket x 1
D0004972 None Centralise Bracket x 1
D0004622 centralise cylinder spacer x 1
R0000572 Bench Assemble Centralise Assembly
r spacer x 1 R0000572 Bench Assemble Centralise Assembly <br/>) - R0015100 Fit Guarding + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard spanner set
'''Parts Required'''
D0001878 Rear Door Saw Mk4 (1879) x 1
D0004584 Outfeed Side Rest x 3
D0015703 Air Gun Bracket x 1
D0016203 Compliance Guard - Saw Lower Front x 1
D0016204 Compliance Guard - Saw Lower Side x 1
D0016265 Saw Front Door: Bernstein Mount Plate x 1
D0016266 Saw Front Door: Bernstein Guard x 1
E0001569 Guard Lock Switch: Bernstein Radius Actuator (Key) x 1
M0000055 Saw Blade Spanner (24mm Combination) x 1
M0001051 Bullet Catch 70 x 12 x 1
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 6
P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x 3
P0001009 Panel Mount Nut (To suit P0001008) x 3
R0015041 Bench Assemble Top Hood Assembly x 1
R0015337 Bench assemble guarding components x 1
R0015338 Bench assemble serial plate x 1
g components x 1 R0015338 Bench assemble serial plate x 1 <br/>) - R0015004 Bench Assemble Gripper + ('''<u>Tools Required</u>''' E … '''Tools Required''' External circlip pliers Standard Hex key set Standard spanner set Reed switch setting box Hammer Standard screwdriver set Rule '''Parts Required''' B0001106 x 20 D0015095 x 8 D0015096 x 2 D0015086 x 1 B0000034 x 2 D0015084 x 2 D0015083 x 1 D0015082 x 1 E0000366L x 1 B0001182 x 2 M0001182 x 2 D0015756 x 1 P0001013 x 1 P0001041 x 1 P0001128 x 1 P0001198 x 2 P0001120 x 1 D0015431 x 1 B0000437 x 1 D0015430 x 1 D0015090 x 2 D0015085 x 1 D0015102 x 2 D0015103 x 2 D0015104 x 2 D0015170 x 2 P0000049 x 1 D0015097 x 2 D0015100 x 2 D0015292 x 1 E0000336 x 1 E0001069 x 1 A0001044 x 4015100 x 2 D0015292 x 1 E0000336 x 1 E0001069 x 1 A0001044 x 4)
- R0015263 Mount drive motor for load shaft + ('''<u>Tools Required</u>''' S … '''Tools Required''' Standard Hex key set Standard Spanner set Long nose pliers '''Parts Required''' B0000041 Feather Key 5 x 5 x 18 Long x 1 B0000142 Feather key 5 x 5 x 25 long B0000240 Geared Motor 0.18kW 18RPM Motovario x1 B0001100 Feather Key 8 x 7 x 30 Long x2 D0006714 Index Torque Limiter (B0189 / B0190) x1 D0015460 Infeed Motor Shaft (2018) x1 D0015461 Infeed Motor Mount x1 D0015462 Infeed Motor Platex1 F0000618 m10 x 70 set boltunt x1 D0015462 Infeed Motor Platex1 F0000618 m10 x 70 set bolt)
- R0015255 Mount Assemblies to Main Frame + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0015291 Datum Flag x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 2 D0015722 Energy Chain Tray Shallow Long x 1 D0015861 Energy Chain Cable Support x 1 R0015007 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015251 Bench Assemble X axis components and energy chain R0015004 Bench Assemble Gripperaxis components and energy chain R0015004 Bench Assemble Gripper)
- R0015322 Remove Electrical Control Cabinet Assembly + ('''<u>Tools required</u>''' standard hex key set External circlip pliers '''<u>Parts required</u>''' fitted cabinet assembly)
- Stuertz Infeed - Freeing Roller under Gripper Arm + ('''Applies to: A2026-A2030 Autoflow Mk4 wi … '''Applies to: A2026-A2030 Autoflow Mk4 with Jetta Locking motors'''
In certain circumstances, the forward clamp roller arm has stuck itself under the gripper arm. Freeing from this situation requires a set process because the GZ axis motor is braked and probably in an overload condition
nfident in using TwinCAT on the VM machine to navigate to settings</div> </div><br/>) - Laser Setup on Flowline/ZX3 for Laser Holes + ('''How to Setup .'''
This will Cover the … '''How to Setup .'''
This will Cover the Basic Alignment of the receiver and Sender setup.
Focusing the Laser and Setting up the Receiver Sensitivity.
Always Make sure Laser Sender and Receiver are clean and both lenses have been wiped with a soft cloth first.
en wiped with a soft cloth first. <br/>) - TB0314 Updating Mint File in Workbench + ( * Updating software can be very complicat … * Updating software can be very complicated, so care must be taken and always ensure there is a route to retrace your steps in the event of a failure – with Baldor .mnt files this is easy because each version is a separate file and therefore easy to load the old one back in again * In general, the Baldor (.mnt) software has been designed to be backwards compatible, but there are a few steps that needed to be taken that made this impossible. In these cases, the front end software (winMulti or winSaw) also needs to be updated – you will get an error to tell you that this is the case * Version numbers have always followed a numerical order, so the higher the number, the later the version * Mnt files should always be stored in ** c:\multi on MH side – called Multi X.xxx.mnt ** c:\saw on Saws or Saw side of flowline – called IgSaw X.xx.mnt aw side of flowline – called IgSaw X.xx.mnt )
- Updating winStugaSaw Software to v4 + (<div class="icon-instructions caution-i …
With the upgrade of the source code editor to Visual Studio 2017, and the associated security changes to Windows, many thing changed with the Windows .net libraries. In order to maintain the code, it needed to be upgraded.
This upgrade had major consequential effects:
# It was not compatible with windows XP any more due to security issues
# A new version of Workbench needs to be installed
any more due to security issues # A new version of Workbench needs to be installed <br/>) - TB0426 Replacement Zebra Printer Setup + (<div class="icon-instructions caution-i … [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions]iv> [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions])
- TB0409 Setting Up Windows 10 PC 2018 + (<div class="icon-instructions caution-i … Please use [[Setting Up Windows PC C0000422-KIT 2023]][[Setting Up Windows PC C0000422-KIT 2023]])
- Setting Up Windows PC C0000422-KIT 2023 + (<div class="icon-instructions idea-icon … stuga.dokit.app/wiki/Setting_Up_C0000422-KIT_-_Full_Hardware_2023</div> </div>)
- R0015336 Pneumatic Output Testing Part 2 + (<u>'''Tools Required'''</u> PCL airline connection 12mm blanking ports Valve Manual over ride tool Standard screwdriver set Additional colleague when setting regulator pressures for outputs <u>'''Parts required'''</u> R0015040 completed module)
- R0015279 Align Backfences + (<u>'''Tools Required'''</u> Standard hex key set Standard spanner set Wire Line setting equipment 600mm rule Workshop Gripper setting jig 2 meter straight edge <u>'''Parts Required'''</u> Fitted and Levelled roller bed assemblies)
- R0015292 Install Cylinder Rails and Align + (<u>'''Tools Required'''</u> … '''Tools Required''' Standard spanner set Standard hex key set Tape measure Wire line Pneumatic cylinder setting jig '''Parts Required''' R0015288 Bench Assemble Transfer slid units and cylinder rails R0015093 Bench Assemble Transfer Beamd units and cylinder rails R0015093 Bench Assemble Transfer Beam)
- R0015310 Install V Notch Subframe + (<u>'''Tools Required'''</u> … '''Tools Required''' Standard hex key set Standard Spanner set Parallel setting blocks 600mm rule 1 meter straight edge 2 meter straight edge 12 " engineers level 12" engineers square '''Parts Required''' D0015151 Shaft End Washer x 8 D0015155 Vertical Spacer Bar x 4 D0015150 shaft 40mm zx v notch x 4 D0015169B cylinder rod bracket x 2 R0015035 Bench Assemble V Notch Componentsinder rod bracket x 2 R0015035 Bench Assemble V Notch Components)
- R0015336 Pneumatic Output Testing + (<u>'''Tools Required'''</u> … '''Tools Required''' PCL airline connection 12mm blanking ports Valve Manual over ride tool Standard screwdriver set Additional colleague when setting regulator pressures for outputs '''Parts required''' R0015040 completed modulet;u>'''Parts required'''</u> R0015040 completed module)
- R0015335 Mount Electrical Cabinet + (<u>'''Tools Required'''</u>
… '''Tools Required'''
Standard hex key set
Standard spanner set
Standard HSS drill set
Standard Tap set
'''Parts Required'''
D0004391E Left hand side sheet x 1 D0015425 Bracket: Beckhoff Box Right Angle x 1
D0015426 Mounting Plate: Airgun Assy x 1
D0015425 Beckhoff right angle mounting plate x 1
P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 1
P0000021 Airgun Assembly x 1
P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2
P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1
P0000278 Regulator 0-2 bar x 1
P0000373 Regulator fixing bracket x 1
R0015016C Electrical cabinet wiring Mod F
xing bracket x 1 R0015016C Electrical cabinet wiring Mod F <br/>) - R0015334 Fit Centralise Front Table + (<u>'''Tools Required'''</u> … '''Tools Required''' Standard hex keyset 1 meter straight edge Large parallels 150mm engineers square Engineers level 300mm '''Parts Required''' H0004543 Gap cover saw finger guard R0000562 Bench assemble centralise top table R0015037 Bench assemble SY Assemblyssemble centralise top table R0015037 Bench assemble SY Assembly)
- TB0444 Renewing CF Card on TwinCAT2 Systems + (<u>Problem</u> These machines … Problem These machines use a CX5020 PC with a 2Gb CF card running TwinCAT2 PLC system. The CF card can fail, which is effectively the windows operating system. The CF card has a very small capacity, so needs to be created from an image. This TB outlines the steps in the process to ensure a successful conclusion. 1. Create a new CF card at stuga using the beckhoff imaging tool on a CX5020 2. Boot up with the CX5020 3. Ensure PLC is set to Enable on start-up (default is config mode) 4. Rename the PC 5. Install TeamViewer host v10 or less from a USB stick 6. If you have a copy of the version of winMulti it was running, copy this in to the c:\ multi folder. If not, a “'''''new version install'''''” will be needed so copy in data from the g:\builds\PC Installs\Autoflow\Multi folder 7. Set up and customer specific network parameters to ensure TeamViewer will work when it is plugged in on site 8. Send to customer Once on site, follow procedure A if the winMulti version is preserved, or B if it is a '''''new version install'''''eserved, or B if it is a '''''new version install''''')
- R0015011 Bench assemble Gripper + (==Introduction==
'''<u>Tools Require … ==Introduction==
'''Tools Required'''
External circlip pliers
Standard Hex key set
Standard spanner set
Reed switch setting box
Hammer
Standard screwdriver set
Rule
'''Parts Required'''
B0001106 x 20
D0015095 x 8
D0015096 x 2
D0015086 x 1
B0000034 x 2
D0015084 x 2
D0015083 x 1
D0015082 x 1
E0000366L x 1
B0001182 x 2
M0001182 x 2
D0015756 x 1
P0001013 x 1
P0001041 x 1
P0001128 x 1
P0001198 x 2
P0001120 x 1
D0015431 x 1
B0000437 x 1
D0015430 x 1
D0015090 x 2
D0015085 x 1
D0015102 x 2
D0015103 x 2
D0015104 x 2
D0015170 x 2
P0000049 x 1
D0015097 x 2
D0015101 x 2
D0015292 x 1
E0001069 x 1
A0001044 x 4
7 x 2 D0015101 x 2 D0015292 x 1 E0001069 x 1 A0001044 x 4<br/>) - Correcting Linearity with Rack Offset File + (Accuracy problem on A2001 was traced to a … Accuracy problem on A2001 was traced to a non-linear rack. This tutorial demonstrates how to test the linearity of a rack and the systems in place to correct the linearity. machine in the 20 year history that has needed these alterations</div> </div>)
- R0000728 R0000729 Stroke Assembly Dismantling + (Assemblies fitted to MK1 ZX4 will require … Assemblies fitted to MK1 ZX4 will require refurbishment at some point of life cycle.
The following instructions should be followed to ensure that correct assembly and setting are performed
'''Tools Required'''
Standard hex key set
Standard spanner set
Double pin saw flange spanner
Drifts and punches
Ballpein hammer
Soft hammer
Degreasing bath
pein hammer Soft hammer Degreasing bath <br/>) - Autocut Taking A Backup + (Backing up is vital to ensure your data is safe in case there is a failure of the PC or Hard Disk Drive)
- R0000164 Spindle Build + (Clear build instructions for the assembly of R0000164 spindle assembly)
- R0000711 Rotary Base Assembly REV2 + (Detailed steps to correctly install rotary … Detailed steps to correctly install rotary gear and journals Checks for correct installation of oil feed system Tolerance limits and requirements '''Tools Required''' Standard hex key set 0-25mm micrometer Ring support blocks for assembly Work Table Mag Base and D.T.I Hepco flat spanner 17mm socket Torque Wrench '''Parts required''' D0006423-2mod Drive ring x 1 D0007651 Face plate x 1 B0000185 journal x 6 B0000186journal x 2 D0006503 Journal washer x 8 D00007692 wiper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1iper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1)
- Z Transom Width Measurement + (Difficulty can be had when trying to accurately measure the width of a Z transom profile section. This guide will show you how to accurately measure the width of the Z section to within 0.1mm which is required when setting up Y notching accurately)
- Placing a TwinCAT3 Machine Under Source Control + (<div class="icon-instructions caution-i … Click [https://stuga.dokit.app/wiki/Changing_Version_Control_to_Visual_Studio here] for the latest procedure For many years, the source code for the PLCs has resided on the G:\drive and then a copy on each and every one of the PCs used to edit the code, so at least one on each machine. This is a recipe for disaster because maintaining all the copies and version numbers is incredibly difficult and adds a lot of time overhead to fixes and changes. This has worked because there has been only one developer, but this is set to change in future as more programmers will be trained and tracking versions becomes more difficult From 2020, the PLC code version control has been improved by using an industry standard source control system called "Git" along with "BitBucket" to store the PLC code in the cloud. The program "SourceTree" is used to commit, push and pull the changes [https://www.atlassian.com/git/tutorials/what-is-version-control Click here] for an introduction to version control using Git This tutorial is a step by step guide to setting up an existing machine or diagnostic PC to a standard uses on all Stuga machines to enable quick, easy and stress free version control.standard uses on all Stuga machines to enable quick, easy and stress free version control.)
- Installation Procedure - Autoflow Mk4 + (General Procedure is * Prepare Area * Unload from Transport * Locate and level infeed table * Locate, level and align machining module * Locate, level and align outfeed table * Fix to floor * Locate waste conveyor system * Guard fencing assembly)
- Correct Adjustment of Saw Anaconda Rotation + (How to correctly Adjust the Saw conduit to prevent it hitting the guard locking device)
- Full Version Upgrade TwinCAT3 WinMulti + (If a PC fails on a machine in the field an … If a PC fails on a machine in the field and the hard drive data cannot be recovered, it is necessary to replace the PC. This may create a version conflict, as the new PC will have later versions of twinCAT installed than the original
This tutorial outlines the steps required to bring all the machine systems up to the latest level to ensure compatibility
ions-text">...This is a one-way process that cannot be reversed</div> </div><br/>) - Disabling a Tool Home or Tool Out Sensor + (If there is a failure of a tool out or too … If there is a failure of a tool out or tool home sensor on the Stuga spindle ring, it is important to be able to quickly disable the input so the machine can continue production until the problem can be properly resolved. The software has an inbuilt functionality to do this - this tutorial takes you through the necessary stepsrial takes you through the necessary steps)
- Commissioning - Off-Cut Laser Sensor + (Infeed Off-Cut Laser sensors are used to c … Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.be larger that the final triggered sensor.)
- TB450 - CMOS Battery replacement + (Internal CMOS batteries are used in PCs to … Internal CMOS batteries are used in PCs to keep a constant power supply to BIOS memory while the main power supply is switched off. These batteries should last up to 5 years when a PC has been left idle. Sometimes these batteries can fall flat before this time either due to being low when sent out or extended use on older machines. The main symptom of a CMOS battery faulting on a Stuga machine is the PC not booting up when mains power is switched on which will be indicated by a “No Signal Detected” message being displayed on the screen. This is due to the BIOS setting “Restore AC Power Loss” going back to its default value of OFF due to the battery faulting. Restoring the BIOS to its original settings is a temporary fix in this situation as it is most likely this will happen again a couple of months down the line (See TB 376 or 213). The battery required is a '''CR2032'''. In the case of the Antec PC, and most commonly, the battery is held in an open housing that can be pushed to release and easily replaced. In PCs such as the Acer Revo the battery needs to be pre-wired with a plug but still easily unclipped and replacedug but still easily unclipped and replaced)
- Monday - Putting Customer Machines On Stop + (It is important that everyone does this th … It is important that everyone does this the same way or confusion and frustration will follow. It is also important to understand how the relationship between a Machine and it’s contract works * Each machine on the “Machine” board needs to link to a “Contract” on the “Service Contracts” board * This allows multiple Machines to have the same “Contract” – eg Customade group contract * The “Contract” is the electronic version or equivalent to the bit of paper that the customer has signed, and contains the start and end dates, etc * For machines that have no contract, I have set up some other “General” contract types. These General Types are not machine specific – ** PAYG – General Pay as you go ** OnStop – Customer is on stop and nothing should be supplied ** AskFirst – Ask KG or management first before supplying goods and services ** Proforma – Payment required before supply of goods and services ** PreDelivery – Before warranty startses ** PreDelivery – Before warranty starts)
- Stuertz Infeed - Check GY Position Parallelism + (It is important that the parallelism of th … It is important that the parallelism of the GY axis to the backfence is set and maintained along the length of the rack. This tutorial describes how to check this parallelism without the need for measuring equipment
Potential Symptoms of a problem
*Gripper cannot pick up offcuts
*Gripper /profile end forced away from backfence
*Accuracy problems
*Gripper wobbles after it has released profile
Use the laptop to enable you to control the Service screen whilst inside the infeed table
Ther gripper setting jig is used to give an accurate and reliable zero to locate the gripper jaw to. Any piece of aluminium reinforcing box section will also work
Create a spreadsheet or a table to log your results,.
ng box section will also work Create a spreadsheet or a table to log your results,. <br/>) - Setting Motor Overload Relays + (It is important to set the Motor Overload … It is important to set the Motor Overload Relays to the correct values according to the motor as if the current is set too low, the motor will continually trip the MCB and if it set too high then the motor will not trip the MCB under fault conditions, leading to the motor burning out.ditions, leading to the motor burning out.)
- Setting Gripper Nose +
- Assembly - R0000377B Mk11 Gripper + (Mk11 Gripper was designed to give a variab … Mk11 Gripper was designed to give a variable stop height position for the Mk10 gripper assembly. This is needed on systems with multiple chambers, where there is no "sweet spot" for the open grip position to suit all chambers. A Somatec turret stop is used to provide different stop heights
The design details are here [https://stugaltd.monday.com/boards/315478853/pulses/640717084 Design Notes]
853/pulses/640717084 Design Notes] <br/>) - Monday - Emails to Updates + (Mondays has changed the way it deals with … Mondays has changed the way it deals with the way it writes updates via email, in a very useful way for us. This will save a lot of time cutting and pasting information from emails. Simply put, * when you send an email, cc: the unique email address for the item in your email you are sending. This is standard practice to get your email into Mondays. * When your contact replies (with reply all) * their reply will now magically appear in the Monday update for the item. * It even strips out the email trail, leaving just the important reply It used to be the case that only members of Stuga.co.uk could send an email directly to an update, but this has now changed…ly to an update, but this has now changed…)
- TB0301 Autoflow Saw Head Reinforcement - Additional Enhancements + (On Autoflow 2 Sawing Centres following 5 y … On Autoflow 2 Sawing Centres following 5 years of use., it has been found that the internal saw centre framework can lose its rigidity. this is probably due to "bruising" or denting of the aluminium joints introducing a slight amount of play. This is exacerbated by the design where it is attached and driven on from the base up A retrofit kit of parts has previously been created to allow additional reinforcement to be introduced within the structural framework. This kit builds upon the first kit to provide further accuracy enhancements by #Adding left right stability with additional slide rails at the top of the subframe #Adding front / back stability by moving the SY axis leadscrew to the same height as the saw table ====Parts required: ==== R0010272 Kit: Saw Frame Rigidity Pt 2 This kit consists of 2 carriage assemblies, specifically designed to provide further rigidity to the top of the Saw Head Assembly. In addition, 2 mounting blocks required to relocate the Saw Y Axis Assembly are also included. This allows the Saw Y Axis Assembly to continue to operate accurately, but improves the life of associated components. See also [[TB0259 Autoflow Saw Head Reinforcement]][[TB0259 Autoflow Saw Head Reinforcement]])
- Device Magic - Adding a Device Email Address + (PM service and service call reports will b … PM service and service call reports will be sent to the engineer's own email address automatically, but '''''only if''''' the device "Email" property is set up correctly.
This needs to be done separately using a device magic account.
's device is renewed or needs to be re-added in Device Magic</div> </div><br/>) - Setting Infeed Loading Wheel + (Setting the pressure and clutch tension on … Setting the pressure and clutch tension on the loading wheel is critical for the reliable and accurate running of the machine If set incorrectly, the profile will slip and not load correctly or will not give an accurate start position for the datum holes The goal is to set the system to a "goldilocks" zone where there is enough pressure and clutch tension to reliably load a bar, but not too much so the clutch limits any correctional movement from the gripper arm on loading e video demonstrates how easy it is for the wheel to become loose</div> </div>)
- Setting Profile Detection Laser Sensor + (Setting the profile sensor correctly is im … Setting the profile sensor correctly is important as it will lead to incorrect offcut measurement.
ensure the sensor is set for the range of different colours</div> </div><br/>) - TB0425 Lenovo Tablet Setup + (Setting up all apps for the engineers Lenovo tablets.)
- ZX5 Transfer Table Setup + (Sometimes the mesh between all the parts i … Sometimes the mesh between all the parts is too tight and left with no adjustment. This causes too much pressure on the moving parts, especially the delrin rollers which are not designed to take heavy loads. Any excess force on them leads to excessive wear and premature failure.s to excessive wear and premature failure.)
- Installing VNC Server and Viewer + (Teamviewer are withdrawing support and are … Teamviewer are withdrawing support and are very dismissive of helping out with teamviewer issues for older operating systems. Sometimes the problem just has to be solved, so there are other tools that can be used to "piggy back" onto a teamviewer connection to an office PC. A reliable, free and simple method is to use VNC. This involves #Installing VNC Server on the old PC that you want to control #Installing VNC Viewer on the Piggy-back PC VNC Viewer can be downloaded [https://archive.realvnc.com/download/get/786/eula/ here] VNC Server can be downloaded [https://archive.realvnc.com/download/get/775/eula/ here]e.realvnc.com/download/get/775/eula/ here])
- Convert TC2 Project to TC3 + (The Beckhoff system provides a system for upgrading to TC3 from a TC2 project. This tutorial goes through the steps required to ensure the links and setup of the original TC2 project are copied through to TC3.)
- Autoflow Maintenance - Machining Centre + (The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention:)
- Autoflow Maintenance - Sawing Centre + (The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention)
- Autoflow Maintenance - Outfeed Table + (The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention)
- ZX5 Datum and Grip Pin Setup + (The ZX5 has a different and much improved … The ZX5 has a different and much improved grip system where we use the 10mm cutter to put holes in the end of the profile. The profile is then gripped by the grip pins to give a more accurate and reliable grip. Along with better machining accuracy, this also allows the X axis to be run at higher speeds and virtually eliminates gripper slip. For it to work accurately and reliably the system first needs to be set up mechanically on both the X and SX axis. And crucially, if the datum is changed the loading position also has to be changed, and vice versa. This is extremely important for the operator, and any on-site maintenance staff to be aware of as changing either one without compensating the other can lead to accuracy issues and miss grips.an lead to accuracy issues and miss grips.)
- TB0447 ZX5 Setup - X Axis Beam Calibration + (The ZX5 has a moveable Beam on the Z axis. … The ZX5 has a moveable Beam on the Z axis. The design reason behind this is to keep the gripper arm short for reliability and stiffness, yet enable it to move out of the way for rear V notching During the calculations for the machining bar recipe, the software has to work out if and when the beam needs to be moved: · If there are no v notches on the bar, then machine all the operations without moving the beam. Beam moves at the very end when ejecting · If there is a V notch, move the bar during the first X axis position where position > beamStrokeLength Therefore, it is very important for the software to know how far the beam moves physically to offset all the positions to allow for it. The distance is measured and entered into parameter beamStrokeLength. It should be around 700mm. beamStrokeLength. It should be around 700mm.)
- TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The ZX5 has two bar measuring systems – th … The ZX5 has two bar measuring systems – the side laser and the sensor array. The side laser scans the bar as it moves into the final loading location, which gives the software a “heads-up” for the length of the bar. If the length is different to expected, the software will then use the sensor array to measure the bar length. There are 2 measurement methods because the side laser is not 100% reliable, especially on shorter lengths below 3000mm. However, it does mean the system does not have to grip and measure / reoptimize each bar length, so improves the cycle time. The sequence is as follows 1. During the conveyor loading, measure the length using the side laser 2. Once loaded to backfence, check the backfence sensor array. 3. If the sensor array rough measurement does not match the laser – a. If the laser measured length < infeedLaserRemeasure, continue and measure with rear sensors b. If the laser measured length < infeedLaserRemeasure, flag an error that laser has not measured correctly. c. If it does match, use the laser value to reoptimize the bar if it is different than expected 4. Load and Grip bar, if necessary, measure accurately with rear sensor arrayssary, measure accurately with rear sensor array)
- ZX5 Alignment Check + (The ZX5 machine can be tricky to align as there are many adjustments designed into the table to offset manufacturing tolerances. This step by step guide follows the correct protocol to ensure the starting point and sequence of alignment is correct)
- Setting Arrow Heads on ZX5 or ZX5-E + (The Zx5 and Zx5e have an upgraded system o … The Zx5 and Zx5e have an upgraded system on the saw centralising which takes the best mechanical features of the standard saw centralising, yet adds an ability to move the central point for Y notches.
In general, this makes it easier to set up, because the overall centralise position can be changed in software , rather than adjusting a cylinder offset, and also to fine tune the centralise position for different profiles
the arrow head position permanently will also alter Y notch depths</div> </div><br/>) - TM018B Microline and ZX3 V Notch Blade Setup + (The engineer will need a reasonable mechan … The engineer will need a reasonable mechanical knowledge, and a working knowledge of the operation of the machine. You will need callipers (+/-0.05mm) and an accurate rule The setting of the V notch blades on a ZX3 Ring revolves around the setting of two groups of parameters: *V and W axis positions *Blade offsets for each blade The rough position of V and W axes is set first, then the individual blade offsets are set, and finally a test is run to tweak the accuracy to gain perfection. There are two “tweaking” parameters for each blade. The two parameters are: *Depth offset – how deep into the bar *X axis offset – position of point of blade relative to the spindle centrelinef blade relative to the spindle centreline)
- TB0422 Commissioning ZX5 Software 2018 + (The first step in commissioning a new mach … The first step in commissioning a new machine is to get the basic software setup correctly installed. Because the software is designed to be very flexible across many machine types, the simplest way to do this is to copy from a recently built similar machine.opy from a recently built similar machine.)
- R0000299 Stroke assembly rebuild Part 2 + (The following instructions should be follo … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
- ZX5 Gripper Energy Chain & Tray Setup + (<div class="icon-instructions caution-i … The main problems we’ve had during commissioning with these energy chains is that if they are not positioned well enough , the chain will clip the button heads that hold the trays to the L brackets To get over this the brackets sometimes need adjusting on the slots along with possibly bending into a better shape or by adjusting the chain bracket position on the slots in the ‘finger’ bracket Things to look out for: *There should be three links which are reversed at the bracket end of the energy chain. *Servo cable and the pipes and cables from the energy chain are fixed with cable ties to the fingers on the bracket to minimise possible movement and twisting which changes where the energy chain sits in the trays, meaning it could start clipping the button heads. *Tray heights and energy chain length, there should be a consistent gap all the way along between the energy chain and the top tray (viewed from inside the tray) and when at the full travel either end the chain shouldn’t be tight hitting the fence too much at the end. *It is also worth checking if all of the links fitted are the same radius type, as we have had occasions where some have been a smaller radius meaning at certain points down the rack the radius of the bend becomes smaller and falls out from the support of the top tray, especially when the gripper is at either end of the rack. There is a code on the side of each link in the energy chain. *A last thing to be weary of is is the end corners of the trays may require bending out, there have been occasions where one chain tray has been slightly more bent in than the other meaning when the chain moves from one tray to the next it clips the corner of the next tray We normally get the gripper on a reversing cycle movement to test this through the twincat project at different speeds, starting slow and working up to higher speeds.gh the twincat project at different speeds, starting slow and working up to higher speeds.)
- X252 Forward Clamp Out Sensor Setup Stuertz Infeed + (The out sensor used for the vorlaufwagen c … The out sensor used for the vorlaufwagen cannot be a standard reed switch because the cylinder that drives this output is a telescoping version. It is impossible to detect the out position. Therefore, a sensor is fitted that must be programmed to set a high output when it detects the full range has been reached The sensor is a [https://www.pepperl-fuchs.com/global/en/classid_53.htm?view=productdetails&prodid=42559#overview Pepperl+Fuchs VDM28-8-L] Datasheet can be downloaded [https://files.pepperl-fuchs.com/webcat/navi/productInfo/45/452859n.pdf?v=20220926110229 here] '''Function''' The distance measurement device contains one transmitter and one receiver incorporated into a single housing. The transmitter light is reflected back to the receiver from a target. The sensor determines the distance to the target and triggers a switching function or supplies the relevant measured value for processing. '''Assembly instructions''' The sensor can be mounted by means of through holes or by using a mounting bracket or mounting clamp Ensure that the surface is level in order to prevent the housing from becoming distorted when the fittings are tightened. It is advisable to secure the nuts and screws using spring washers in order to prevent the sensor from being incorrectly adjusted. '''Connection''' Connect the device in accordance with the connection diagram in the datasheet. '''Adjustment''' The green LED lights up when the operating voltage is switched on. Adjust the sensor so that the laser point is on the gripper bodyso that the laser point is on the gripper body)
- Gripper Push Speed on Flowline and ZX + (There is a cylinder called Grip push, when … There is a cylinder called Grip push, when bar is moved to its unload position the Gripper Comes OFF then Grip push is activated to push the profile of the gripper to clear ready for the Eject push onto transfer Table. The video shows what happens if the grip push is set too fast. The speed of the cylinder is Far too Fast and is Throwing/punching back down machine. -- This needs to be slowed Down. machine. -- This needs to be slowed Down.)
- PLC Source Control - Adding a Repository + (These instructions give details of how to … These instructions give details of how to set up a repository so that any changes made to the core project will be tracked. For the git source control to work it is important that GIT has been chosen as the source control program. see Prerequisits. The instructions start from : The project has been created and PLC code has been loaded in to the TwinCAT Xae Shell program.oaded in to the TwinCAT Xae Shell program.)
- Autocut Regular Maintenance + (This checklist needs to be carried out at … This checklist needs to be carried out at regular intervals, in conjunction with the daily maintenance.
gt; <td>Single Shift Full Time </td><td>Bi-Weekly </td></tr><tr> <td>Up to 50% utilisation </td><td>Monthly </td></tr></table>)Use Profile Regularity 2-3 Shifts per day Weekly Single Shift Full Time Bi-Weekly Up to 50% utilisation Monthly - Alignment guide using wire line + (This dokit is to help with the use of a wi … This dokit is to help with the use of a wire line to set alignment correctly on mechanical build up. Using a wire line correctly will ensure a very accurate straight line is achieved . Accuracy of + - 1 mm over any distance can be achieved using the following method. Using one incorrectly can also easily be done.! The steps shown can be applied to all types of alignment , when you have a vertical face on components that require aligning. face on components that require aligning.)
- ZX3 Counterweight Installation + (This guide explains how to install the counterweight assembly on the current ZX3 ring)
- Units of Measure modification CIM50 + (This guide is to show how to amend units o … This guide is to show how to amend units of measure of existing stock items. If a new product is created please ensure the Units of measure is always set up correctly from the beginning . The CIM50 guide for Units of Measure setup is [https://cimservices.sharepoint.com/:w:/s/Cim50PartnerMarketing/EZhA_HF6SFJLmkVO5WANYXIBZdMx4hbVnuY3cdIF78p7lg?rtime=FcNQz7GE2Ug here]4hbVnuY3cdIF78p7lg?rtime=FcNQz7GE2Ug here])
- R0015146 Pneumatic pipe Installation Part 2 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001106 Plug in reducer 12-8mm x 1 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
- R0015146 Pneumatic pipe Installation Part 3 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001106 Plug in reducer 12-8mm x 1 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
- R0015146 Pneumatic pipe Installation + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this
See Electrical department for prepared components from above assembly
'''Tools Required'''
Pipe cutters
Pipe identification markers
Flush cutters
'''Parts Required'''
P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6
P0000047 Bulkhead Elbow 6mm x 1
P0000159 Fitting: Stem Blanking Plug 6mm x 2
P0000160 Fitting: Flow Controller In Line 6mm x 2
P0000551 6mm inline Quick Exhaust Fitting x 3
P0001030 Fitting: SMC 6mm Equal Tee x 1
P0001008 regulator x 3
P0001009 Regulator nut x 3
P0001106 Plug in reducer 12-8mm x 1
P0001107 Fitting 12mm equal tee x 1
P0001166 12mm tube to tube elbow x 1
12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1 <br/>) - Setting Ultrasonic Sensor - Horizontal + (This involves setting a "window" for a minimum and maximum range when mounted horizontally)
- PC Bios Power settings + (This power setting enables the PC to Boot … This power setting enables the PC to Boot up automatically when power is first detected, in other words when the power is “lost” and then “returns”, without the necessity to manually press the power button on the PC. The following description shows how to set the auto power-up on but beware this Technical Bulletin only applies to the “ASUS UEFI Utility BIOS Version 2.x.x”. This document is for the ASUS Pcs For the Dell PCs use [[PC Bios Power Settings - Dell]]ttings - Dell]])
- Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
- R0019207 Upgrade SR Axis Spigot + (This upgrade utilises upgraded parts to en … This upgrade utilises upgraded parts to ensure a mechanical fix is maintained between the SR axis gearbox and main drive pin , whilst also giving the ability once upgraded for the gearbox to be removed with minimal mechanical time. three main parts will be replaced in this upgrade, obsoleting the removed parts Main components of upgrade D00004019E Turntable Mk5 D0004033E Alignment disc Mk5 D0004147E Turntable shaft Mk5nt disc Mk5 D0004147E Turntable shaft Mk5)
- Filling Out An Online Daily Timesheet Form + (We are using Monday.com to handle daily ti … We are using Monday.com to handle daily timesheet entries. The layout of the form has been designed to make data input as minimal as possible. We are looking to improve accuracy of time capture, cut down administration time and to make historical data available without the need to store paperwork or take pictures. You will only be able to view and edit your timesheet when logged into your Monday.com account. Other employees are unable to see your data.her employees are unable to see your data.)
- Ecoline - Datum and MitreOffset Tests + (When an Ecoline is commissioned, the posit … When an Ecoline is commissioned, the positional accuracy needs to be set up.
These are also useful tests to check if the machine is maintaining positional accuracy
tent, repeatable results before making any parameter changes</div> </div><br/>) - Easily resizable forms for any screen resolution in Visual Studio + (if you have issues with certain screen resolutions cropping off buttons and need to design a form which works at all resolutions, and also allows the user to resize parts of the form, then this tutorial will help.)
- R0000299 Stroke assembly rebuild + ( The following instructions should be fol … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
Français
English
Deutsch
Español
Italiano
Português