Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

R0015311 Install and Align Datum rollers + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015245 Module C support arm alignment + (1 Move channel 2 section up or down to co … 1 Move channel 2 section up or down to copy height of adjacent channel 3. Use the tabs as the reference points 2 Use 2 meter straight edge and level between points indicated Move channel 2 at the end indicated, to give a level reading 3 Tighten bolts to hold in place
3 Tighten bolts to hold in place <br/>)
R0015357 Fit Guards + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015255 Mount Assemblies to Main Frame + (Using the first point used to set the brac … Using the first point used to set the brackets , measure the gap indicated and replicate this measurement on the other 4 points . This is adjusted by moving the indicated bracket up or down .

...If enough adjustment isnt available on remaining positions, first position can be moved up and new measurement taken

sitions, first position can be moved up and new measurement taken</div> </div>)
R0015264 Fit Loader chains to arms + (It is vital to tension the securing grubsc … It is vital to tension the securing grubscrew for the drive sprockets correctly Use a straight ended 4mm hex key and extension bar to apply as much tension as possible to the m8 grubscrew Then add 2 drops of self wicking thread locker to complete the tension processead locker to complete the tension process)
R0015290 Bench Assemble Top guard + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015324 Install pipe and cable looms + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015263 Mount drive motor for load shaft + (Apply adhesive and lock off all grubscrews in spherical bearings in all positions (9 off bearings ))
R0015262 Drive shaft fitting + (Attach 9 off B0001150 to load arms as sho … Attach 9 off B0001150 to load arms as shown . ensure correct position is used for mounting of bearings . Use 2 off M8 x 30 socket countersink fasteners per bearing to align and fix to arms Ensure greasing point of bearing is facing towards the front of the machine as shown towards the front of the machine as shown)
Convert TC2 Project to TC3 + ( #Open Visual Studio #Create a new TC3 pro … #Open Visual Studio #Create a new TC3 project called [BuildNo] in c:\TwinCAT\Stuga\ #Make sure "Create Directory..." is Unticked #Right Click on the project name and select ‘Load Project from TwinCAT 2.11 Version…’ #Click Cancel on the two windows asking to convert the PLC project #Ignore or cancel any warnings about libraries (this part will be replaced later)

...Once created, you will have a copy of all the devices and boxes in the project with the correct naming.

f all the devices and boxes in the project with the correct naming.</div> </div><br/> )
Autocut Monthly Maintenance + ([[Autocut Open Guard Doors|https://stuga.dokit.app/wiki/Autocut_Open_Guard_Doors]])

Saje uPVC Unloading Process + (Including the chop saw table Leaving a clear route for the 2.4m x 7.5m table to roll in)

TB0314 Updating Mint File in Workbench + ( # Contact Stuga service to download latest version to the machine via teamviewer # On the g:\ drive G:\Builds\Latest Software Versions. # From Dropbox service\Machine Software\ )
Stuertz Infeed - Check GY Position Parallelism + ( #Datum the machine and move GY axis to ze … #Datum the machine and move GY axis to zero, GZ to 25 #Place the jig against the backfence and offer it up to the Gripper Jaw #If the GY datum is set correctly, the rear outer face of the jig should be just in contact with the rear serrated jaw #If this is not the case, set GY datum correctly his is not the case, set GY datum correctly )
TM018B Microline and ZX3 V Notch Blade Setup + (A calibration mnd file has been written to … A calibration mnd file has been written to help line up the x offsets called VTEST. This program creates the following pattern on the bottom of the profile using a 10mm spindle and the notching blades themselves: Run the VTest operation on a length of large outer frame of at least 1m long. Put the operation at a position of 500mm. The pattern allows you to measure the offsets required with calipers.

...Profile is viewed from the bottom face, Basically turn it over when it comes of the transfer table.

face, Basically turn it over when it comes of the transfer table.</div> </div><br/>)
Upgrade ZX Machine to Beckhoff Drives and Control + (Before the upgrade is despatched to site, … Before the upgrade is despatched to site, the servo system needs to be assembled and pre-wired in its enclosure.
*Drill off Fan detail in right hand side of cabinet. A 114mm hole saw and arbor has been purchased for this. *Drill and fit 4 adjustable feet in the bottom of the cabinet. 4 extra nuts will be in the kit. The height of the feet does not need to be set at this stage. *Drill off all servo drives. For ZX3 machines, the rack will be as follows: AX8640-AX8118-AX8206-AX8206 and for a ZX4 the will be: AX8640-AX8118-AX8206-AX8206-AX8206 (the extra drive is for the V and W axes). *Pre-wire the rack (inc STO links) and the cabinet fan with the cable provided in the kit. leave the spare coil of cable in the cabinet ready for running on-site. *Plug in the 2x15m green etherCAT cables. *The enclosure bottom plate is left off to allow the cable entry on site. '''''*for detailed wiring information, please use drawing packs from Monday.com board.*'''''e use drawing packs from Monday.com board.*''''')
Setting Up Email Production Reports + (Navigate to Settings->Parameters)
Autoflow Power On + ((minimum 6 bar to machine))
ZX5 Alignment Check + ( * Check backfence roller alignment to infeed * Check roller heights to infeed and outfeed )
Autoflow Maintenance - Outfeed Table + ( * Clean Stainless Steel Bed of swarf and … * Clean Stainless Steel Bed of swarf and remove any tape that may have transferred onto the bed during normal operation * Lightly oil shaft on underside of bed, lightly oil cylinder rods * Lghtly oil Hepco rail, 1 -2 pumps of grease into Linear Bearings * Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds * Check Hepco rail, Linear Bearings, Shafts and cylinders for damage or wear gs, Shafts and cylinders for damage or wear )
Setting Up Windows PC C0000422-KIT 2023 + ( * Connect Keyboard and mouse * Connect network * Connect monitor )
Setting Up C0000422-KIT - Full Hardware 2023 + (Remove the PC from the Dell box with power adapter and power cable. Keyboard and mouse (if supplied) can be returned to stores (not needed here))
R0000204 Notching gear boxes assembly + (It is vital for correct function that all … It is vital for correct function that all the shown components are thoroughly degreased before assembly . To do this, wash all parts with FE10 solvent spray and dry with airline.

...Ensure your work area is very clean and free from Dust/swarf. Use a clean cloth or paper towel to lay on your bench to ensure parts remain clean once washed

o lay on your bench to ensure parts remain clean once washed</div> </div><br/>)
WinMulti Shutdown procedure + (Once you have a black screen with a small blue text box in the middle you are safe to press the physical red 'POWER OFF' button on the console.)
Ecoline Site Installation Guide + (This is what the taper on the roller approach is for - to raise the profile onto the rollers)
Ecoline - Disabling V axis To Swap Faulty Drive + ([[Archiving a TwinCAT Project]])
Create a TwinCAT Project from Scratch + (<div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...From Z071 there is no twinSAFE project as the Estop circuit is hard wired</div> </div>)
Guide to Fitting Eject Push Sensors on ZX Machines + (A retrofit kit will be sent with all the p … A retrofit kit will be sent with all the parts needed to carry out this task. The assembly number for the kit is R0019218. If you have any feedback regarding this kit, please use this assembly number. It is important to check the parts you have received against the assembly list to ensure you have nothing missing before starting the job.e nothing missing before starting the job.)
R0015146 Pneumatic pipe Installation Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015333 Fit Clamp Assembly + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015337 Bench Assemble Guarding Components + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015146 Pneumatic pipe Installation Part 3 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015037 Bench Assemble SY Assembly Part 2 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation Part 3 + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R000569E Bench Assemble Head Spindle Posts + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015100 Fit Guarding + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0000574 Fit Motor and Swarf Chute + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015334 Fit Centralise Front Table + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015305 Install Wiring loom for Rotary loom + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All bolts to be pen marked once adhesive applied and correct tension added)
R0015328 Install Base and Turntable + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015146 Pneumatic pipe Installation + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0015034B ZX5 Module B Wiring Loom installation + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
R0000571 Fit and Level Cut Tables , Finalise Eject + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
ZX5 Installation Procedure 2023 Pneumatic connections + (All control pneumatic connections will be … All control pneumatic connections will be identified with identification numbers All permanently fed supply lines will be identified by the use of Red pneumatic pipe All Emergency stop switched air feeds will be identified by the use of Blue pneumatic pipeentified by the use of Blue pneumatic pipe)
Setting up an Ecoline Barcode Scanner + (All refurbished Ecolines will now be provi … All refurbished Ecolines will now be provided with USB barcode scanners. This may be a hand held device or an 'Orbital' scanner attached to the infeed table depending on the customer's preference. Use the provided cable to plug the scanner in to the nearest available USB port. There will be 2 USB extension cables coming from the PC inside the cabinet. One will go to the console to control the keyboard and the touchscreen and the other will go to the infeed table junction box to control one or two barcode scanners.ox to control one or two barcode scanners.)
R0000299 Stroke assembly rebuild Part 2 + (Always use Loctite 243 on all fasteners fitted unless stated different All bearings should be an acceptable fit, with Loctite 641 and FE10 solvent used if required All fasteners should be marked once finalised)
ZX5 Production R0000548E Module G to R0015040 Module F alignment + ( # X axis of module is levelled from the t … # X axis of module is levelled from the two indicated points . Use a 2 meter straight edge between these points and an engineers level on top # y axis is levelled from these two indicated points . an engineers level rested on this face is sufficient for levelling ed on this face is sufficient for levelling )
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Before installing module B, module C rolle … Before installing module B, module C roller tables should be double checked for correct positioning 1 To do this inspect tables 1, 2,3 and 4 for level as shown. 2 Also inspect alignment with 2 meter straight edge. All rollers should be on the same height and no bump up should be present when moving the straight edge over the table. 3 Ensure fixed table is at same height as rollers Report any discrepancies to supervisor for correct remedial action to supervisor for correct remedial action)
ZX5 Installation Procedure 2023 Part 2 + (Check X axis alignment of horiczontal and … Check X axis alignment of horiczontal and vertical rollers using 2 meter straight edge and feeler gauges Any discrepancy must be reported and rectified if present Tolerance 0.002" / 0.05mm [https://stugaltd.monday.com/boards/3628350043/pulses/4665028475][[R0015311 Install and Align Datum rollers]]
[[R0015311 Install and Align Datum rollers]] <br/>)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Position module F at end of Module E infeed frame Approximately Align Saw roller back fences to Saw infeed back fences Approximately align X axis position by setting the to frames spaced at the distance shown of 20mm)
Repairing R axis datum pin + (Drill a 2.5mm hole in the datum pin shoulder. Refit to datum plate and use the drilled hole as a guide to drill the aluminium spindle plate. Remove datum pin and tap the hole in the plate using the M3 tap.)
R0015268 Pneumatic module Test + (Ensure area is clear and free from personnel)
CX5120 Replacement + (Ensure replacement CX5120 is setup using [[TB0451 CX5120 Beckhoff PC Setup|https://stuga.dokit.app/wiki/TB0451_CX5120_Beckhoff_PC_Setup]] before sending to site)
ZX5 Transfer Table Setup + (The rollers on top are mounted on eccentri … The rollers on top are mounted on eccentric bushes. We only need these just tight enough to not allow any slop or vertical play. Slacken the cams off completelely, you will need an 8mm spanner with the faces ground down to fit in the space. Slide the plate onto the rail and tighten the eccentric bushes until any vertical play is removed. Lightly try to move the assembly on the X axis, if there is any slop then it needs to be a little tighter but probably no more than an 1/8th of a turn. Once set you should still be able to spin the rollers by hand, but still feel a fair bit of resistance. Once set slide the assembly over the full length of the V rails to check fo any tight spots. If there are then you need to check that the two halves of the fail are fully mated!!! two halves of the fail are fully mated!!!)
Recovery of Bar Queue following winMulti Crash + (First you need to check out the bar queue … First you need to check out the bar queue to see if it is the same as the actual bars on the transfer table #Restart winMulti #Count the total number of bars on the saw infeed and transfer table #Compare with the number of bars on the saw queue

...If you have some offcuts on the screen, this can help identify the queue position by looking at the length of the offcut

If there is '''one more bar''' actually on the table than on the bar queue screen, follow the process below to add the missing bar to the queue.han on the bar queue screen, follow the process below to add the missing bar to the queue.)
Autocut Adding New Profile + (Firstly, we need to make sure that the pro … Firstly, we need to make sure that the profile will physically go through the machine, open the top gaurd door. Ideally, you will have a 1 metre offcut of the profile - work out the best way for the profile to go through the machine. Push the profile through the machine by hand to ensure no catching areas etc.e by hand to ensure no catching areas etc.)
TB0390 Fitting SR Datum Sensor + (Fit U Bolt and Sensor Bar to Table Post on infeed side of saw. See Image for height)
TB0422 Commissioning ZX5 Software 2018 + (Follow [https://stuga.dokit.app/wiki/TB0409_Setting_Up_Windows_10_PC_2018 technical bulletin 409] to setup PC with correct naming conventions and TeamViewer.)
ZX5 Transfer Table Crank set up + (Follow the instructions in [[Programming Eaton DE Drive|this]] … Follow the instructions in [[Programming Eaton DE Drive|this]] tutorial.

...It is vital that the Eaton drives are programmed correctly as the distance the cranks travel and the time they take to stop depend on the acceleration and deceleration of the drive.

...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.

xt">...Programming the drives after the mechanical set up may lead to crashes. Ensure this is done first.</div> </div><br/>)
TB0425 Lenovo Tablet Setup + (Go to the PlayStore and download the e-Drawings app. This will cost (currently £1.25) therefore ask appropriate member for a company card.)
ZX5 Adjusting V Notch Depth and Position + (If the blades do not meet properly, or form a "W" shape, the mechanical setup is not correct. Please follow procedure: [[ZX5 V Notch Blade Mechanical Setup|https://stuga.dokit.app/wiki/ZX5_V_Notch_Blade_Mechanical_Setup]] <br/>)
ZX5 Installation Procedure 2023 + (Identify if either saw infeed or multi head outfeed is the logical frame to place first . Consider access to machine when installing 1st frame Consider handing of machine)
R0015280 Module E Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed * Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testinglies are at a sufficient stage for testing)
R0015257 Module C Pneumatic Tests + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed
* Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testingassemblies are at a sufficient stage for testing)
Flowline 6 to 6o5m Extension + (Clean and remove any dirt/grease/imperfections on the box section ready the the new rails. If any of the tapped holes are compromised, re-tap 6mm.)
ZX5 MH Infeed Basic IO Test and Setup + (Make sure the reset of the Estop circuit w … Make sure the reset of the Estop circuit works. Be aware when resetting this will reset the air to home all pneumatics. Test each emergency stop button individually (Button box, infeed rear middle and end) making sure this breaks the circuit when pressed and the air is dumped. The Infeed beam sensor should be tested, when broken should also break the circuit and dump the air. Check on Service menu - IO tab that each input works correctly for each Estop unit.input works correctly for each Estop unit.)
ZX5 Datum and Grip Pin Setup + (In SETTINGS > PARAMETERS > MEASUREMENT > loadingPos=11 If set at a different figure, update to 11 and SAVE)
Commissioning - Z-Block Calibration + (On the '''Service > IO''' tab use output '''Y214''' to turn the infeed turret. <br/>)
Stuertz Infeed - Align and dowel GX rack + (Using the T0001090 alignment tool, check each 1m section of the rack is aligned to its neighbour <br/>)
Autocut Daily Maintenance + (Once the machine has stopped production, press an emergency stop button to ensure the machine is safe to work on)
R0015320 Pneumatic Output Test + (Output testing will be carried out under a no-emergency stop situation ensure pcl coupling is used for ability for quick disconnection Ensure all colleagues are aware of testing and ensure good working practise is followed)
R0015336 Pneumatic Output Testing Part 2 + (Output testing will require valve operatio … Output testing will require valve operation with no e/s circuit Ensure the following Work area is clear from all components not required for testing All colleagues are aware of the procedure being undertaken No additional colleagues are working on the module PCL coupling is accessible to release pressure in case of emergency Testing procedure is fully adhered tocy Testing procedure is fully adhered to)
R0015336 Pneumatic Output Testing + (Output testing will require valve operatio … Output testing will require valve operation with no e/s circuit Ensure the following Work area is clear from all components not required for testing All colleagues are aware of the procedure being undertaken No additional colleagues are working on the module PCL coupling is accessible to release pressure in case of emergency Testing procedure is fully adhered toy Testing procedure is fully adhered to)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Position module A in front of module B Use Infeed back fence to Multi head datum rollers as initial alignment guide for Y axis Set gap of 23mm -+ 2mm between module A roller frame and module B roller block)
TB0415 Method to Prevent Loosening of Saw Blade + (Position on shaft not important.)
Upgrade - Gripper Slider Mechanism + (Remove all existing parts, including the profile lever, slideway and bearings, and the spring. Install new stronger slideway)
R0010309 Ecoline Ultrasonic Material Loaded Upgrade + (Remove old material load assembly from mac … Remove old material load assembly from machine. Held on by 2 off M6 socket caps indicated 2 Disconnect switch/sensor. Depending on variant fitted either Unscrew M8 plug connection to disconnect for sensor style Or Disconnect 2 off fork connections onto rear on switch 3 Disconnect bloweronto rear on switch 3 Disconnect blower)
Move SR Datum Sensor to Higher Level R0019217 + (Replace the upper brace plate with D0016338. This has the detection plate for the SR axis added on the top)
Laser Setup on Flowline/ZX3 for Laser Holes + (The laser sender needs to have a clear pat … The laser sender needs to have a clear path to the laser receiver, its really important that this is parallel and the beam does not bounce off the inside of any of the aluminium mounting block. Slacken off the Nuts above and below Laser to move up/down and side/side.below Laser to move up/down and side/side.)
Saje uPVC Unloading Process +
Setting Infeed Loading Wheel + (Use the heaviest profile you can find - a … Use the heaviest profile you can find - a full bar of door T or transom Place it under the wheel so it can be fed into the machine

...Ensure the infeed flights are out of the way

ons-text">...Ensure the infeed flights are out of the way</div> </div><br/>)
Beckhoff AX8000 Flowline Upgrade + (The first step does not involve being on s … The first step does not involve being on site or carrying out any physical tasks. However, trying to gain some familiarisation before carrying out the upgrade can save time and confusion down the line. Please read through this tutorial before upgrading the machine. The attached files and steps will walk you through the upgrade that somebody else has already experienced. This will give you a free look at any issues or learnings that have already been made. or learnings that have already been made.)
TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The laser should be aligned to ensure the … The laser should be aligned to ensure the beam is level up / down and parallel to the backfence. The path should follow the Yellow edge of the lift rollers on the infeed table. Length feedback from the measurement system is visible all the time on the service form.
# Measure and mark the infeed table at fixed positions from the loading fence at MH end – (3m, 4m, 5m, 6m) # Use a short offcut of profile with a label on the end to act a a fixed reflector at the marked positions – check against the feedback on the screen. # Adjust the lengthMeasureOffset parameter to get the screen measurements to match reality (+/-10mm)e screen measurements to match reality (+/-10mm))
GE Control Components Changeover + (The supplier that we use for the supply of … The supplier that we use for the supply of our control components advised us of the need to changeover. The components that have been made unavailable are all of the GE components. This includes, all MCB's, all contactors (24Vdc, 24Vac, 230Vac), all motor overloads and any auxiliary components to go with these devices. See pictures for reference.these devices. See pictures for reference.)
R0015278 Mount Completed Assemblies + (Use loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
Fitting R0019199 Upgrade: Autoflow Slewing Ring Guard Kit + (This procedure must be done in conjunction with moving the SR Axis Datum to a position higher and ant the front of the machine to [[Move SR Datum Sensor to Higher Level R0019217]] <br/>)
TB0385 Upgrading to winMulti v6 + ( (Defaults to Config mode after the TwinCAT update))
R0015028D ZX5 Hepco Beam Alignment Module C part 2 + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts once finalised)
R0015140 Spindle energy chains and looms + (Use Loctite 243 on all fasteners Pen mark bolts once finalised)
R0015242 Level and Adjust Roller beds module C and E + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015292 Install Cylinder Rails and Align + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015294 Fitment of wire basket and feed pipes + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015093 Bench Assemble Transfer Beam + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0015348 Fit Flexible Ducting + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015347 Bench Assemble Duplex extraction unit + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015119 Mount Assemblies + (Use Loctite 243 on all fasteners Use Loctite 570 on all threaded pneumatic connections Pen mark all bolts when finalised)
R0000738 Pneumatic Installation + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015035 Bench Assemble V Notch Components + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000738 Pneumatic Installation Part 2 + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0000738 Pneumatic Installation Part 3 + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015253 Fit Slider units + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all bolts to show finalised)
R0015028D ZX5 Hepco Beam Alignment Module C + (Ensure additional spacer is removed from jigs when using for alignment on module C)
R0015314 Fit Z Axis Drive components + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
J0001000H Autoflow Mk4 Mechanical installation-Alignment + (Use footprint drawing to determine machine location for installation)
R0015245 Module C support arm alignment + (1 Move channel 2 section up or down to co … 1 Move channel 2 section up or down to copy height of adjacent channel 3. Use the tabs as the reference points 2 Use 2 meter straight edge and level between points indicated Move channel 2 at the end indicated, to give a level reading 3 Tighten bolts to hold in place
3 Tighten bolts to hold in place <br/>)
R0015311 Install and Align Datum rollers + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015090 Bench Assemble Roller Tables + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015332 Mount Backfences and Align + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015321 Bench Assemble Guards and Doors + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
R0015007 Bench Assemble Roller Tables Machining Outfeed + (13 off Check part D00150001 has been supplied to new specification Check indicated hole, should measure 8.2mm. If not open up with hand drill Drawing change requested 06/06/23 to amend from 8mm to 8.2mm <br/>)
R0015273 Module E support arm alignment + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)