Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.
Liste de résultats
- TB0383 Mint and RS Automation Drive Setup + (The following will show how to setup a mint controller i.e. NextMove ESB-2 with an RS Automation Drive and servo motor but to act as a stepper motor and being controlled from the ESB-2 as a stepper.)
- Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3 + (<div class="annotatedImageDiv" typeof=" … Autoflows from A2001 to A2015 were initially produced with TwinCAT2 software. This has now been superseded with TwinCAT3 which then has the benefit of compatibility with version 6 front end software.
The original PC cannot be used because
*It is not powerful enough to run v6 front end
*The operating system cannot be upgraded to Windows 10
*It cannot be upgraded to TwinCAT3
The Beckhoff C6015 PC has been chosen to be the replacement PC. It is compact, yet powerful enough to run the v6 front end and TwinCAT in the same
. It has an upgrade to 1.9Ghz 4 core processor.
Because it has a limited 40Gb SSD memory, a compact 64Gb memory stick is inserted into the USB 3.0 port. This acts as a separate drive for the DDRIVE dynamic storage for all machine setup. The internat drive is for the Operating System only. This mimics the current Autoflow setup of a remote Camera PC, hence the camera PC can be retired after the upgrade
era PC, hence the camera PC can be retired after the upgrade<br/>) - R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (<nowiki>'''<u>Tools required&l …
'''Tools required''' ;P0001070 Valve Base: Type 41 6 Position Ø6 x 2<br /><br />P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8<br /><br />P0001101 Male straight 12mm to 1/4 bsp x 5 <br /><br />P0001102 Male elbow 12mm to 1/4 x 2<br /><br />P0001186 Valve 24v dc SMC x 12 <br /><br /><br /><br /><br/></nowiki>)
Tape rule
Steel rule
standard hex keys
Standard HSS drill set
Standard Tap set
Hack saw
Ball Pein hammer
Centre punch
'''Part Required'''
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 3
P0000024 Fitting: Hex Nipple 1/4 BSP x 1
P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2
P0000097 Fitting: Elbow Adaptor 8mm - 1/4 BSPT x 1
P0000159 Fitting: Stem Blanking Plug 6mm x 3
P0000160 Fitting: Flow Controller In Line 6mm x 2
P0000279 Female Cross 1/4'' NPT x 1
P0000297 HighLow Pressure Valve x 1
P0000419 Air Service Unit OH (P0283)x 1
P0001070 Valve Base: Type 41 6 Position Ø6 x 2
P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8
P0001101 Male straight 12mm to 1/4 bsp x 5
P0001102 Male elbow 12mm to 1/4 x 2
P0001186 Valve 24v dc SMC x 12 - R0015342 Bench Assemble Outfeed Parts + (<nowiki>'''<u>Tools Required&l …
'''Tools Required''' gt;<br />P0001068 Valve Base: Type 41 2 Position Ø6 x 1<br /><br />P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1<br /><br />P0001163 1/4 bsp male silencer x 2<br /><br />P0001186 Valve/ 5/2 smc x 2 <br /><br />P0001198 1/8 bsp 6mm speed controller x 4<br /><br />P0000394 reed switch holder x 2<br /><br />P0000444 Reed switch pneumax x 2</nowiki>)
Standard Hex Key set
Standard spanner set
Standard screwdriver set
Bearing press
Test box for cylinder switch function
'''Parts Required'''
B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8
B0000236 90 Deg Grease Nipple M6 ST/ST x 4
D0004311 Side Eject Block x 2
D0004591 Side Eject Housing x 2
D0004592 Eject Housing Plate x 2
D0005200 Safety Dead Stop Block x 1
D0005201 Safety Dead Stop Backer (5357) x 1
D0005202 Safety Dead stop Yoke (5358) x 1
D0005203 Safety Slider Cap x 2
H0004626 Shaft 16mm: 275 Eject Push x 4
M0000101 Compression Spring 11 D 15 D 25 Long x 1
P0000035 Cylinder 25x160 x 2
P0000174 Fitting: Plug 1/4'' BSP (Grubscrew Type x 2
P0000201 Flow Controller 6mm x M5 Elbow x 2
P0000367 16mm bore X 125 stroke with rod end clevis x 1
P0000369 Clamp to suit P0000367 x 2
P0000327 Reed Switch: Pneumax 1580U (5.0m Lead) x 2
P0001068 Valve Base: Type 41 2 Position Ø6 x 1
P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1
P0001163 1/4 bsp male silencer x 2
P0001186 Valve/ 5/2 smc x 2
P0001198 1/8 bsp 6mm speed controller x 4
P0000394 reed switch holder x 2
P0000444 Reed switch pneumax x 2 - R0015316 V notch Final Assembly Part 2 + (15/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/NTcwZDVkYWY1NWI0NGQwM2IyZTQ0ZTQ4NjQ3OWYzMDE Here])
- R0000963E Bench Assemble Z axis Components + (03/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/NzA1MmFjYThjZTMxNGM4Zjg3MzkyZmUyZWE0YjlhNTQ Here]<br/>)
- R0002913E Install and Align Rotary head Subframe PART 2 + (04/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/YmUzNjU5YzI3NzdmNDE2YmE0MTdjN2M3ZmNhZGY4NzY Here])
- R0015329 Fit Head Spindle Posts + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard flat hand file
Emery tape 120
standard hand tap set
Stubby hex key set
Ratchet/hex bit set
Blade flange spanner
'''Parts Required'''
D0004002 Webb x 1
D0004003 Top Shaft Block x 2
D0004004 Brace Support Bar (D7451) x 1
D0004157 Motor plate spacer x 3
D0004342 Damper Bracket (5312) x 1
D0007451 Brace Support Bar OH (D4004) x 1
D0015490 Saw Turntable Sensor Flag x 1
D0015491 Saw Turntable Flag Bracket x 1
H0004024 Infeed Clamp Post x 1
H0004025 Outfeed Clamp Post (5302) x 1
H0004510 Shaft 30mm: 540 Saw Stroke x 2
P0000055 Adjustable Damper 200mm (Saw Stroke) x 1
R0000560 Bench Assemble Spindle x 1
R0000569E Bench Assemble Head Spindle Posts Mk5 x 1
V0000043B Saw Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1
Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1 <br/>) - R0000558E Bench Assemble Base and Turntable + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard spanner set
Heat gun
Large Internal Circlip pliers
Standard circlip pliers
8mm hand reamer
Grease gun
Torque wrench
'''Parts Required'''
B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1
B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4
B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1
B0001088 Circlip 125mm Internal x 1
C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1
C0001179-100 Gearbox NPTO 100-1 x 1
D0004019E Turntable Mk5 (5334E) x 1
D0004033E Alignment Disc Mk5 x 1
D0004147E Turntable Shaft Mk5 x 1
D0004320E Thrust Bearing Housing Mk5 x 1
D0004336 Stay Bar x 2
D0004514E Turntable Base Mk5 x 1
D0004516 Front Bearing Block (5294) x 2
D0010778 Turntable Stop Arm x 1
D0010796 Turntable Housing Cover x 1
H0004631 Shaft 30mm: Base Slide x 2
M0001176 M6 Stainless lock washer x 4
D0015663 SR Axis Motor Guard x 1
ainless lock washer x 4 D0015663 SR Axis Motor Guard x 1 <br/>) - R0015278 Mount Completed Assemblies + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard Hex key set
Standard spanner set
300 mm rule
1000mm rule
'''Parts Required'''
D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1
D0015583 Take Up Beam Joiner x 1
D0015598 Datum Flag: Saw Infeed x 1
D0015717 Energy Chain Angle Bracket Lower x 5
D0015718 Energy Chain Angle Bracket Upper x 5
D0015720 Carriage Bracket x 1
D0015721 Energy Chain Tray Deep Long x 1
D0015723 Energy Chain Tray Shallow x 1
D0015724 Energy Chain Tray Deep x 1
D0015725 Energy Chain Tray Shallow Medium x 1
D0015742 Takeup Pad Right ZX5 x 1
E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1
R0015011 Bench Assemble Gripper
R0015063 Bench Assemble Roller Tables
R0015096 Bench Assemble Transfer Drive Assembly
R0015101 Bench assembly take up assembly
R0015286 Bench Assemble X axis components and energy chain
R0015286 Bench Assemble X axis components and energy chain <br/>) - R0015063 Bench Assemble Roller Tables + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard Hex key set
Standard spanner set
Tape measure/Rule
8.2mm HSS drill
Drill
'''Parts Required'''
B0001092 Plastic roller x 48
B0001103 Bush flange x 28
B0001220 Spacer x 28
D0015001 Roller Bed Cylinder Arm x14
D0015002 Shaft 10mm: 58mm Rod End x 14
D0015003 Roller Bed Rail 375mm x 6
D0015004 Roller Bed Rail 550mm x 2
D0015005 Roller Bed Rail 1000mm x 10
D0015006B Roller Bed Arm Bracket x 14
D0015010 Rod End Spacer x 28
D0015283 Saw Infeed Backfence Plate x 5
D0015481 Shaft 8mm: 50mm Cylinder Pivot x 14
D0015547 Sensor Blower Plate x 1
D0015603 Roller Bed Pivot Shaft (silver steel) x 14
D0015608 Saw Infeed Backfence Plate (Full Length) x 5
E0001120 Sensor: Ultrasonic M8 20-150mm x 1
P0000049 Cylinder Spherical Bearing M10 x 1.25 x 14
P0000200 Elbow Adaptor 6mm - M5 x 1
P0001152 Cylinder 25 x 25 x 14
P0001198 Fitting Speed controller 1/8 x 6mm tube x 28
P0000160 flow regulator x1
ontroller 1/8 x 6mm tube x 28 P0000160 flow regulator x1 <br/>) - R0015278 Mount Completed Assemblies Section two + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chainsembly R0015286 Bench Assemble X axis components and energy chain)
- R0000558E Bench Assemble Base and Turntable Part 2 + ('''<u>Tools Required</u>''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1)
- R0000574 Fit Motor and Swarf Chute + ('''<u>Tools Required</u>''' … '''Tools Required''' standard hex keys Standard spanner set 1 meter steel rule Copper slip Chute flap template jig Standard Hss drills Standard taps Ratchet 3/8 drive and 13mm socket Copper/hide hammer '''Parts Required''' B0000048 Taperlock Set SPZ 80-2 1210-24 x 1 B0001175 Saw V-belt (special size 987mm) for 500mm blade x 2 D0005628 Saw chute infill panel x 1 H0004637 Offcut Chute (H0005333) x 1 H0004660 Chute Bracket x 1 P0000609 Reed Switch Mount (Tie Bar) x 3004660 Chute Bracket x 1 P0000609 Reed Switch Mount (Tie Bar) x 3)
- R0000962E Bench assemble Y axis Components + (03/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/YWVjMGU3NWE2YTA1NDgyNWI4YzExYjJiMjFmNGIxOWU Here])
- R0015255 Mount Assemblies to Main Frame + (17/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/MzUxNGRlOWVlMGI4NGU5MzhkYmI2MTk5ZmRlZWI0YTk Here])
- R000569E Bench Assemble Head Spindle Posts + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard Hex key set
Standard spanner set
Internal circlip pliers
Consumable 4mm yellow grease line
Pneumatic pipe cutters
'''Parts Required'''
B0000002 Bearing: 12/28dia x 8mm Sheilded x 2
B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4
B0001061 Grease fitting x 6
D0004001 Head Bearing Block x 3
D0004021 Upstroke Plate x 1
D0004078 Motor Plate (5311) x 1
D0004099 Cylinder Bearing Block x 1
D0004256 Cylinder rod bar x 1
D0004343 Lower Damper Bracket (5313) x 1
D0004445 Semi circular slit strip (5533) 500mm x 1
D0004634 Chute Sawblade Strip 500mm (5532) x 1
D0004733 Belt Adjuster Pulley x 1
D0004734 Belt Adjusting Bar x 1
D0004735 Belt Adjuster Pin x 1
D0010780 Grease Manifold x 1
H0004444 Semi-circular Guard (5332) x1
P0000009 Fitting: 1/4 BSPT - 6mm Elbow x 2
P0000037 Magnetic Cylinder 40 x 185 with 15mm rod extension x 1
P0000308 Flow Controller In Line 6mm x 1
rod extension x 1 P0000308 Flow Controller In Line 6mm x 1 <br/>) - R0000971E Bench Assemble R Axis Gearbox + (03/09/2025 Moved to Confluance Click [https://stuga-ltd.atlassian.net/wiki/external/NDE2NGQzYjdiNzhlNDBiOTg2ZGUyMzg0MWMyNWM0MzU Here] <br/>)
- R0015087 Pneumatic Connections + ('''<u>Tools require</u>'''
P … '''Tools require'''
Pipe cutters
Number identification
Flush cutters
'''Parts required'''
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 8
P0000160 Fitting: Flow Controller In Line 6mm x 2
P0000551 6mm inline Quick Exhaust Fitting x 7
P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x1
P0001022 Regulator Bracket: to suit P0001008 x 1
A0000343 energy chain x 1
A0000344 energy chain bracket set x 1
D0015577 Fixed energy chain bracket x 1
P0001030 6mm compact tee x 12
ed energy chain bracket x 1 P0001030 6mm compact tee x 12 <br/>) - Stuertz Infeed - Freeing Roller under Gripper Arm + ('''Applies to: A2026-A2030 Autoflow Mk4 wi … '''Applies to: A2026-A2030 Autoflow Mk4 with Jetta Locking motors'''
In certain circumstances, the forward clamp roller arm has stuck itself under the gripper arm. Freeing from this situation requires a set process because the GZ axis motor is braked and probably in an overload condition
nfident in using TwinCAT on the VM machine to navigate to settings</div> </div><br/>) - Laser Setup on Flowline/ZX3 for Laser Holes + ('''How to Setup .'''
This will Cover the … '''How to Setup .'''
This will Cover the Basic Alignment of the receiver and Sender setup.
Focusing the Laser and Setting up the Receiver Sensitivity.
Always Make sure Laser Sender and Receiver are clean and both lenses have been wiped with a soft cloth first.
en wiped with a soft cloth first. <br/>) - GY GZ axis setup with Jetter Motors + ('''WARNING:''' '''The Jetter motor on th … '''WARNING:''' '''The Jetter motor on the GZ axis has a brake. Releasing the brake without control could be harmful/dangerous.''' '''Use the Air Counterbalance rig to assist if necessary.''' This assumes that the motors are connected to the Beckhoff drive and are free to move.o the Beckhoff drive and are free to move.)
- TB0426 Replacement Zebra Printer Setup + (<div class="icon-instructions caution-i … [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions]iv> [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions])
- R0015066 Bench Assemble Saw Motor Assembly + (<u>'''Tool Required'''</u>
… '''Tool Required'''
Standard hex key set
Standard spanner set
Cutting disc
Standard hand taps
'''Parts Required'''
A0000013 32mm Conduit Adaptorx 1
A0000027 Flexible Conduit Ø32mm x 1
D0004079 Saw Motor (Modified Front Flange) x 1
D0004437 Motor Conduit Bracket x 2
D0004835 Flex conduit plate x 1
D0004997 Connector Support Block (5360) x 1
D0004999 Reed Switch Terminal Box x 1
D0005219 Turntable Nozzle x 1
D0008198 Chute Flap x 1
H0008200 Chute Flap Bracket x 1
P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1
1 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1 <br/>) - R0015274 Fit X Axis Gearbox and Motor + (<u>'''Tools Required'''</u> … '''Tools Required''' Feeler gauge set Standard hex key set Standard Tap set Torque wrench (0-50nm) Extended 4mm hex bit 1/8 drive '''Parts Require''' D0015073B x 1 C0001212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 201212 x 1 H0008301 x 1 C0001122K x 1 D0015290 x 2 M0001087 x 2)
- R000718E Stage 2 spindle assembly + (<u>'''Tools Required'''</u>
… '''Tools Required'''
0.05mm feeler gauge
Standard hex key set
Standard spanner set
Rule
6mm punch
Ball pien hammer
'''Parts Required'''
D0007990 cylinder anchor x 7
D0007648 end plate x 4
D0007649 Double slide end plate x 4
D0007686 single motor plate x 4
D0007723 Double slide motor mount x 4
D0007687 Motor mount x 4
D0007600 Cylinder anchor x 4
D0015856 hard stop x 4
t x 4 D0007600 Cylinder anchor x 4 D0015856 hard stop x 4 <br/>) - R0015101 Bench Assemble Take Up Assembly + (<u>'''Tools Required'''</u>
… '''Tools Required'''
Standard hex key set
Standard spanner set
'''Parts Required'''
D0008281 Takeup Boss Cap x 4
D0015581 Fixed Pivot Bracket x 4
D0015584 Cylinder Trunnion Plate x 1
D0015590 Takeup Arm ZX5 x4
D0015593 Takeup Arm Pin ZX5 x 4
D0015595 Takeup Arm Washer 4mm x 4
D0015596 Takeup Bearing Block Short x 4
D0015605 Fixed Pivot Bracket End Plate x 4
D0015736 Hard Stop Backplate x 1
D0015737 Hard Stop Shaft x 1
M0001077 Rubber bump stop M6 x 1
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 1
P0000049 Cylinder Spherical Bearing M10 x 1.25 x 1
P0001075 Trunnion Pin for CG1 Cylinder x 1
P0001076 Trunnion Bracket for CG1 x 1
P0001112 Cylinder 32 x 125s Locking
P0001198 Fitting: Speed Controller 1/8" x 6mm Tube
Locking P0001198 Fitting: Speed Controller 1/8" x 6mm Tube <br/>) - B0000025 B0001175 Belt Identification + (A Guide to correctly identify the variant of drive belt required for ZX5, ZX4 ,ZX3 S-65 and Flowline saw modules Belts will vary across blade sizes and Pully diameters Key indicator is pulley size, over blade size)
- Changing the Flowline Ops Password + (A password can be set up within FlowlineOps that limits access to the Edit Machining and Edit Profiles buttons, This tutorial will explain how to setup or change this password.)
- Setting up TwinCAT Drive Manager for AX8000 Drives + (AX8000 drives require a Measurement projec … AX8000 drives require a Measurement project to be added which gives you a specialised drive manager screen for these drives This needs to be installed separately form a file that can be downloaded from Beckhoff or is in g:\design\TwinCAt3 TE5950-TC3-Drive-Manager-2.zipn\TwinCAt3 TE5950-TC3-Drive-Manager-2.zip)
- ZX5 - ZX3 Hepco alignment Module E Saw Infeed + (Alignment and check procedure for mounting … Alignment and check procedure for mounting of hepco rail To main frame Parts required B0001102 hepco rail D0015492 5 off vertical adjustment plate D0015493 5 off Lateral adjustment plate D0015072 1 off Carriage Plate B0000184 journal wiper 4 off B0000185 journal 2 off B0000186 journal 2off Hepco Levelling Jig Hepco rail v block jigs Hepco rail Drive rack pitching jigk jigs Hepco rail Drive rack pitching jig)
- R0000728 R0000729 Stroke Assembly Dismantling + (Assemblies fitted to MK1 ZX4 will require … Assemblies fitted to MK1 ZX4 will require refurbishment at some point of life cycle.
The following instructions should be followed to ensure that correct assembly and setting are performed
'''Tools Required'''
Standard hex key set
Standard spanner set
Double pin saw flange spanner
Drifts and punches
Ballpein hammer
Soft hammer
Degreasing bath
pein hammer Soft hammer Degreasing bath <br/>) - Autocut Taking A Backup + (Backing up is vital to ensure your data is safe in case there is a failure of the PC or Hard Disk Drive)
- R0000711 Rotary Base Assembly REV2 + (Detailed steps to correctly install rotary … Detailed steps to correctly install rotary gear and journals Checks for correct installation of oil feed system Tolerance limits and requirements '''Tools Required''' Standard hex key set 0-25mm micrometer Ring support blocks for assembly Work Table Mag Base and D.T.I Hepco flat spanner 17mm socket Torque Wrench '''Parts required''' D0006423-2mod Drive ring x 1 D0007651 Face plate x 1 B0000185 journal x 6 B0000186journal x 2 D0006503 Journal washer x 8 D00007692 wiper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1iper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1)
- Z Transom Width Measurement + (Difficulty can be had when trying to accurately measure the width of a Z transom profile section. This guide will show you how to accurately measure the width of the Z section to within 0.1mm which is required when setting up Y notching accurately)
- Placing a TwinCAT3 Machine Under Source Control + (<div class="icon-instructions caution-i … Click [https://stuga.dokit.app/wiki/Changing_Version_Control_to_Visual_Studio here] for the latest procedure For many years, the source code for the PLCs has resided on the G:\drive and then a copy on each and every one of the PCs used to edit the code, so at least one on each machine. This is a recipe for disaster because maintaining all the copies and version numbers is incredibly difficult and adds a lot of time overhead to fixes and changes. This has worked because there has been only one developer, but this is set to change in future as more programmers will be trained and tracking versions becomes more difficult From 2020, the PLC code version control has been improved by using an industry standard source control system called "Git" along with "BitBucket" to store the PLC code in the cloud. The program "SourceTree" is used to commit, push and pull the changes [https://www.atlassian.com/git/tutorials/what-is-version-control Click here] for an introduction to version control using Git This tutorial is a step by step guide to setting up an existing machine or diagnostic PC to a standard uses on all Stuga machines to enable quick, easy and stress free version control.standard uses on all Stuga machines to enable quick, easy and stress free version control.)
- Full Version Upgrade TwinCAT3 WinMulti + (If a PC fails on a machine in the field an … If a PC fails on a machine in the field and the hard drive data cannot be recovered, it is necessary to replace the PC. This may create a version conflict, as the new PC will have later versions of twinCAT installed than the original
This tutorial outlines the steps required to bring all the machine systems up to the latest level to ensure compatibility
ions-text">...This is a one-way process that cannot be reversed</div> </div><br/>) - Ecoline - Disabling V axis To Swap Faulty Drive + (If a drive fails on an Ecoline, the V axis … If a drive fails on an Ecoline, the V axis can be utilised to enable the Ecoline to still run as a machining centre, albeit with V notching now disabled. This is a better situation than no machining at all, as all factories have V notching capability in addition to an Ecolineching capability in addition to an Ecoline)
- Create a TwinCAT Project from Existing Project + (If you are confident and proficient in usi … If you are confident and proficient in using the Visual Studio editor to create TwinCAT projects, you can shortcut a lot of the data inputting by copying and modifying an existing project. This will keep the naming conventions and links exactly the same
ne has exactly the same EtherCAT box, drive and module setup</div> </div><br/>) - Setting Motor Overload Relays + (It is important to set the Motor Overload … It is important to set the Motor Overload Relays to the correct values according to the motor as if the current is set too low, the motor will continually trip the MCB and if it set too high then the motor will not trip the MCB under fault conditions, leading to the motor burning out.ditions, leading to the motor burning out.)
- IP Camera Viewer exe Setup + (It is useful to be able to see a quick vie … It is useful to be able to see a quick view of all cameras on a machine at once. A freeware program is available to do this IP Camera Viewer.exe
Ensure you have the IP address of the cameras to hand, and that the cameras are active and setup to [[Hikvision Camera Setup]].
The cameras should have a fixed IP address
ras should have a fixed IP address <br/>) - TB0447 ZX5 Setup - X Axis Beam Calibration + (Moved to Confluence 17/12/2025 [https://stuga-ltd.atlassian.net/wiki/spaces/~5570585b7bb5d1bc31430e886883cbc774c182/pages/89423875/TB0447+ZX5+Setup+-+X+Axis+Beam+Calibration ZX5 Setup - X Axis Beam Calibration] <br/>)
- Updating Teamviewer Host + (Older versions of Teamviewer are being pha … Older versions of Teamviewer are being phased out by the Teamviewer company from September 15th 2021. The advice on the website suggests you need to upgrade to version 15. However, v15 is not compatible with the older Windows XP machines in the field. The latest XP compatible downloadable version of the Host program is 13.2 and is available [https://download.teamviewer.com/download/version_13x/TeamViewer_Host_Setup.exe here] Regrettably, the update process on older versions is not simple, and frustratingly cannot be done remotely. It needs intervention from an operator at the machine with a small amount of technical know-how with a small amount of technical know-how)
- StuertzCloud - Creating Local SQL Database + (See [[StuertzCloud - Setup Overview]] … See [[StuertzCloud - Setup Overview]] for an overview of the setup.
This tutorial covers the setup of the Local SQL Express database instance and creating a "ProOpt" database structure on it.
*This database installed on the 'Location' local network. *The 'Machines' write their production data to it *The 'Gateway' software uploads this data to the StuertzCloud server See Also [https://stuga.dokit.app/wiki/StuertzCloud_-_Installing_Gateway StuertzCloud - Installing Gateway] [https://stuga.dokit.app/wiki/StuertzCloud_-_Setting_up_Stuga_Machine_to_Write_Production_Data StuertzCloud - Setting up Stuga Machine to Write Production Data] [https://stuga.dokit.app/wiki/StuertzCloud_-_Creating_a_Customer_Location StuertzCloud - Creating a Customer Location]
SQL Server Management Studio (SSMS) installed to manage the databases</div> </div> <br/>) - ACEpc Changing IP address using netedit + (The ACEpcs use two different systems for c … The ACEpcs use two different systems for connecting a network #NETBeui - this was used on earlier machines but reliability depends on the customer network setup. Reconfiguration after initial setup is difficult #IP addressing - A setup system was written using IP addresses to connect. This is a little harder to set up, but is easier to change later. A special program called netedit was written which updates all the correct files in the backgroundes all the correct files in the background)
- Adding TwinSAFE projects to AMI Motors + (The AMI8xxx-3100 motor series is a TwinSAF … The AMI8xxx-3100 motor series is a TwinSAFE enabled motor. To enable this motor to work with a non-TwinSAFE system, a TWINSAFE project needs to be placed into the Safety Logic circuit on board the motor. This dokit describes this process.
====Prerequisites==== *TwinCAT machine project connected, scanned and debugged *Drive Manager 2 Project installed *AMI motors connected and powered up *Latest Device Description (ESI) updates - see Updating Device Description Tables *AMI Motor TwinSAFE Project from [https://stugaltd.monday.com/boards/4881973586 Software Versions Board] For instructions on how to create the AMI Motor twinSAFE project from scratch, see [[AMI TwinSAFE Workaround - Safety Project Creation]]
[[AMI TwinSAFE Workaround - Safety Project Creation]]<br/>) - Replacing Baldor Microflex Drive with RS Automation + (The Baldor Microflex drive with Beckhoff m … The Baldor Microflex drive with Beckhoff motor was a drive system combination that has now been superseded with a better performance system using an RS Automation Drive and motor combination The Part number for the upgrade is R0019052X Kit: X Axis Replacement using RS Automationit: X Axis Replacement using RS Automation)
- Convert TC2 Project to TC3 + (The Beckhoff system provides a system for upgrading to TC3 from a TC2 project. This tutorial goes through the steps required to ensure the links and setup of the original TC2 project are copied through to TC3.)
- Beckhoff AX8000 Flowline Upgrade + (The Flowline range (Mk3, ZX3, ZX4) are Stu … The Flowline range (Mk3, ZX3, ZX4) are Stuga built and designed machines for prepping and cutting uPVC windows and doors. The Flowline is the first machine of the Stuga 'U' shaped machines which has prepping and cutting working in the same machine package. The Flowline is still a fantastic machine for the industry, however, due to the age of the machines and older control systems becoming obsolescent, we have had to find an upgrade route that does not only keep the machine going, but also provides improvements from the original model and up-to-date technology to future proof the machine. The upgrade that we have developed for the Flowline is supplied from an automation supplier named Beckhoff. We also use Beckhoff on our new build machines. This gives us better lead times, more understanding of the products and better diagnostics/ support for our customers. The drive system that we use is called the AX8000 series. These drives are a compact multi axis servo system that use an EtherCAT interface and STO safety functions. These servo drives, coupled with Beckhoff AM8*** series OCT servo motors provide quicker installations and all round performance increases from any system we have previously used. To drive all of the new system, we are using a Beckhoff IPC controller that runs TwinCAT 3. This links into the system via EtherCAT. All of the machine can now link together via EtherCAT to provide quick and stable communications. This tutorial will give you step by step guides on the physical upgrade requirements needed when upgrading a Flowline Mk3 to a Flowline Mk3 with Beckhoff AX8000 Control. Each step will provide you with written information and pictures to guide you through the upgrade. Each step will contain necessary information which will also provide you with rationale for the design and an idea of the benefits over using different methods. Please always feel free to provide Stuga with any feedback on this document or its contents.feedback on this document or its contents.)
- GE Control Components Changeover + (The GE control components are now obsolete … The GE control components are now obsolete and we have had to find a new manufacture to use. We have decided to go with Eaton control equipment for this. We are using the same supplier for these products and we have the added benefit if the supplier holding these parts in there stores. We had a choice to use either ABB, Eaton or Schneider components. Although all of the individual Eaton components are a direct replacement for the GE components, there are certain situation that we may be tripped up. This includes times when we need to change a motor breaker that has an auxiliary block connected to it. We can change the breaker but the GE auxiliary block will not fit on the new Eaton one. This means that the Eaton components need to have different part numbers to the GE components. This document will layout the new part numbers and what they relate to and instructions on how they are added and changed in the Sage system. are added and changed in the Sage system.)
- PC Recovery Process + (The PCs are now shipped with a memory stick that includes a full recovery image. If the system fails in future, this allows a full recovery of the initial setup of the entire drive. Mouse and Keyboard are required for recovery process.)
- Updating Beckhoff TwinCAT3 Backend Version + (The TwinCAT3 beckhoff systems have a speci … The TwinCAT3 beckhoff systems have a special version of TwinCAT installed - the "Runtime" version XAR (eXtended Automation Runtime). This differs from the full "Engineering version XAE that is installed in the front end and camera PCs in that it is the bare bones of TwinCAT for machine running purposes. '''It does not have the Visual Studio editor in it.''' The runtime version may need updating to 3.4024.xx to allow the latest front end and PLC code to work the latest front end and PLC code to work)
- TB0422 Commissioning ZX5 Software 2018 + (The first step in commissioning a new mach … The first step in commissioning a new machine is to get the basic software setup correctly installed. Because the software is designed to be very flexible across many machine types, the simplest way to do this is to copy from a recently built similar machine.opy from a recently built similar machine.)
- R0000299 Stroke assembly rebuild Part 2 + (The following instructions should be follo … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
- ZX5 Gripper Energy Chain & Tray Setup + (<div class="icon-instructions caution-i … The main problems we’ve had during commissioning with these energy chains is that if they are not positioned well enough , the chain will clip the button heads that hold the trays to the L brackets To get over this the brackets sometimes need adjusting on the slots along with possibly bending into a better shape or by adjusting the chain bracket position on the slots in the ‘finger’ bracket Things to look out for: *There should be three links which are reversed at the bracket end of the energy chain. *Servo cable and the pipes and cables from the energy chain are fixed with cable ties to the fingers on the bracket to minimise possible movement and twisting which changes where the energy chain sits in the trays, meaning it could start clipping the button heads. *Tray heights and energy chain length, there should be a consistent gap all the way along between the energy chain and the top tray (viewed from inside the tray) and when at the full travel either end the chain shouldn’t be tight hitting the fence too much at the end. *It is also worth checking if all of the links fitted are the same radius type, as we have had occasions where some have been a smaller radius meaning at certain points down the rack the radius of the bend becomes smaller and falls out from the support of the top tray, especially when the gripper is at either end of the rack. There is a code on the side of each link in the energy chain. *A last thing to be weary of is is the end corners of the trays may require bending out, there have been occasions where one chain tray has been slightly more bent in than the other meaning when the chain moves from one tray to the next it clips the corner of the next tray We normally get the gripper on a reversing cycle movement to test this through the twincat project at different speeds, starting slow and working up to higher speeds.gh the twincat project at different speeds, starting slow and working up to higher speeds.)
- Upgrade - R0000173 Conveyor Motor + (The original style of conveyor is used on many machines, but the motor that powers it is no longer available. This guide will allow a different motor/gearbox to be used.)
- Stuertz Infeed - Align and dowel GX rack + (The rack on a Stuertz infeed is a helical … The rack on a Stuertz infeed is a helical type and is supplied unpinned, as the motor is not connected before delivery to Stuga The alignment must be checked then dowelled with 5mm roll pins The racks are already located in the "Y" direction with location pins, this procedure is purely to align the racks to each other in the GX directionhe racks to each other in the GX direction)
- VM Upgrade Hardware + (The upgrade is to prep the machine ready for adding a Virtual Mahine (VM) to the setup.)
- Units of Measure modification CIM50 + (This guide is to show how to amend units o … This guide is to show how to amend units of measure of existing stock items. If a new product is created please ensure the Units of measure is always set up correctly from the beginning . The CIM50 guide for Units of Measure setup is [https://cimservices.sharepoint.com/:w:/s/Cim50PartnerMarketing/EZhA_HF6SFJLmkVO5WANYXIBZdMx4hbVnuY3cdIF78p7lg?rtime=FcNQz7GE2Ug here]4hbVnuY3cdIF78p7lg?rtime=FcNQz7GE2Ug here])
- R0015146 Pneumatic pipe Installation Part 3 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
- R0015146 Pneumatic pipe Installation + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this
See Electrical department for prepared components from above assembly
'''Tools Required'''
Pipe cutters
Pipe identification markers
Flush cutters
'''Parts Required'''
P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6
P0000047 Bulkhead Elbow 6mm x 1
P0000159 Fitting: Stem Blanking Plug 6mm x 2
P0000160 Fitting: Flow Controller In Line 6mm x 2
P0000551 6mm inline Quick Exhaust Fitting x 3
P0001030 Fitting: SMC 6mm Equal Tee x 1
P0001008 regulator x 3
P0001009 Regulator nut x 3
P0001107 Fitting 12mm equal tee x 1
P0001166 12mm tube to tube elbow x 1
12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1 <br/>) - R0015146 Pneumatic pipe Installation Part 2 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
- Allocations + issuing received parts + (This involves splitting down received orde … This involves splitting down received orders into the JC/Pick bins the parts have been allocated to by Sage. If there are parts to be allocated, after filling in the 'this delivery' column and pressing save, if there are parts to be allocated a list will appear. this list is in order of part number and in the sub-screen after highlighting each part number the specific Job card numbers will show quantities required for each bin and also the quantity to be allocated from the order received.y to be allocated from the order received.)
- Ecoline - Setting V Notches on winMulti Software + (This is the full setup procedure for V not … This is the full setup procedure for V notches on an Ecoline. This should only be needed on initial commissioning or if the shape of the notch has changed due to some physical intervention, for example -
- Blade Change
- Blade buckled
here is no sense carrying on because you cannot complete this setup unless the machine is consistent and reliable</div> </div> <br/>) - ACEpc Installing netedit with NetSetGo disk + (This procedure will completely overwrite a … This procedure will completely overwrite any data on the hard drive of the ACEpc.
This is not a problem on a flowline where the data resides on the main MH hard drive in a shared directory c:\saw.
If this process is to be carried out on a standalone saw or router, make sure the data is backed up first.
e sure the data is backed up first. <br/>) - Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
- ZX5 Transfer Table Crank set up + (15/12/2025 Moved to Confluence Click [https://stuga-ltd.atlassian.net/wiki/external/OTE4MTgyN2RlYjQ2NGRlYTgyZjRhMDc5ZmIyY2MyMTg here])
- Fitting Zx5 Crank Upgrade + (This upgrade replaces the crank arm assemb … This upgrade replaces the crank arm assemblies on Z065, Z066 and Z067 with a direct drive system to improve reliability
This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes
></div> <div class="icon-instructions-text">...Motors must be rewired for Delta and NOT Star</div> </div> <br/>) - B0000082b Motor replacement For Obsolete part B0000082 + (To rectify the obsoletion of B0000082 driv … To rectify the obsoletion of B0000082 drive motor, the following replacement kit has been designed to enable continued support of older assemblies within stuga machines . The kit consists of a new motor and appropriate gearbox, adapter plate and new fasteners . Also details are included here for a small modification to enable the upgrade to function correctly Following parts are required for this upgrade B0000082b load motor and gearbox 1 off D0008225b adapter plate F0000189 M6 x 25 set bolts 4 off F0000058 A form washer 4 off F0000190 M8 x 40 set bolts 2 off F0000007 M5 x 16 cap head bolt 4 off off F0000007 M5 x 16 cap head bolt 4 off)
- PLC Source Control - Selecting GIT as the source control Plug-in + (TwinCAT3 can use different source control programs for source control. These instructions show how to select Git as the source control Plug-in.)
- R0010309 Ecoline Ultrasonic Material Loaded Upgrade + (Upgrade of load sensor For infeed table on … Upgrade of load sensor For infeed table on Ecoline machines
'''Component list'''
A0001046 P Clip 6mm Steel / Rubber Liner x 2
D0010973 Material Loaded Sensor Plate x 1
E0001104 PreMade Cable: M8 Socket 4 Way Cable 5m x 1
E0001120 Sensor: Ultrasonic M8 20-150mm x 1
M0001053 Copper Tube 6mm x 4.4mm 10m Coil x 0.3
P0000046 Fitting: 'Y' Adaptor 6mm x 1
P0000069 Tube to tube fitting 6mm x 1
P0000160 Fitting: Flow Controller In Line 6mm x 1
000160 Fitting: Flow Controller In Line 6mm x 1 <br/>) - Upgrade Autoflow to Windows 11 + ('''Update 2024''' - Upgrades now consist o … '''Update 2024''' - Upgrades now consist of a new Windows 11 PC with VM for the front end and a C6017 PC for the back end.
Upgrading an Autoflow to Windows 11 involves upgrading two PCS
#The Beckhoff control PC - replaced with a C0001225-KIT
#The Camera PC - replaced with a C0000422-KIT with a VM setup. this now becomes the front end PC
===For Historical reference, these are the pre-2024 notes: === ''Upgrading an Autoflow to Windows 10 on site involves upgrading two PCS'' #''The Beckhoff control PC'' #''The Camera PC'' ''
'' The Beckhoff PC is not upgradable so needs to be completely replaced. We use the miniature [https://www.beckhoff.com/english.asp?industrial_pc/c6017.htm Beckhoff C6017] for this ''It is not cost effective to upgrade and old camera PC, so a new one is supplied'' ===''Notes''=== *''The Beckhoff PC is now powerful enough to run the front end and back end.'' *''The camera PC is there to replace the camera PC on site and contains the storage for the machine cameras'' *''Because the Beckhoff PC has limited hard drive space, the DDRIVE will be on the cameraPC''hard drive space, the DDRIVE will be on the cameraPC'') - R0000299 Stroke assembly rebuild + ( The following instructions should be fol … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
Français
English
Deutsch
Español
Italiano
Português