Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

Stuertz Infeed - Align and dowel GX rack + (The rack on a Stuertz infeed is a helical … The rack on a Stuertz infeed is a helical type and is supplied unpinned, as the motor is not connected before delivery to Stuga The alignment must be checked then dowelled with 5mm roll pins The racks are already located in the "Y" direction with location pins, this procedure is purely to align the racks to each other in the GX directionhe racks to each other in the GX direction)

R0015316 V notch Final Assembly + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex key set

Standard Spanner set

ZX5 Blade tightening tool

Compressed air connection with regulation (for axis support)

'''Parts required'''

A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2

A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2

B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4

B0000173 Blanking plug foc x 28

B0000426 Linear Rail MSB25 400mm Long (AMT) x 4

D0015156 Saw Bearing Plate x 2

D0015161 Saw Plate x 4

D0015162 Saw Mid Spacer Bar x 1

D0015163 Saw Bearing Spacer Bar x 1

D0015168B Balance Cylinder Bracket x 2

D0015169B Cylinder Rod Bracket x 2

D0015179 Energy Chain Bracket x 2

D0015180 Datum Switch Bracket (VZ) x 1

D0015183 VY Stop x 2

D0015235 VY Datum Switch Bracket x 1

D0015236 VY Energy Chain Bracket - Fixed x 1

D0015237 VY Energy Chain Bracket - Moving x 1

D0015250 Safe Sensor Block x 1

D0015251 Safe Sensor Finger x 1

D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2

D0015452 Scissor Cable Retainer x 1

D0015541 Energy Chain Deflector x 1

D0015704 Energy Chain Support Plate x 1

E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2

E0001185 Elte Saw motor x 4

M0001087 Rubber Bump Stop M6 Ø20x24 x2

P0000010 1/8 6mm elbow x 1

P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1

P0000023 Fitting: Hex Nipple 1/8 BSP x 1

P0000026 Silencer 1/4 BSP x 1

P0000050 Fitting: Silencer 1/8'' BSP x 1

P0000077 Straight Adaptor 8mm - 1/8BSP x 1

P0000140 Fitting: Quick Exhaust Valve 1/8" x 1

P0001040 Fitting: 1/8BSP Hex Head Silencer x 2

P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2

P0001133 Cylinder: Ø50 x 500 x 2

P0001134 Floating Joint M18x1.5 x 2

P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2

P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1

P0001142 Adjustable Damper 150mm stroke (3000N) x 1

P0001144 Reed Switch Mounting Band for Ø50 cyl x 2

R0015084 Bench assemble and Drill Off Swarf chutes

V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4

BJ3-1 x 2 P0001133 Cylinder: Ø50 x 500 x 2 P0001134 Floating Joint M18x1.5 x 2 P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2 P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1 P0001142 Adjustable Damper 150mm stroke (3000N) x 1 P0001144 Reed Switch Mounting Band for Ø50 cyl x 2 R0015084 Bench assemble and Drill Off Swarf chutes V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 </nowiki>)
R0015342 Bench Assemble Outfeed Parts + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex Key set

Standard spanner set

Standard screwdriver set

Bearing press

Test box for cylinder switch function

'''Parts Required'''

B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8

B0000236 90 Deg Grease Nipple M6 ST/ST x 4

D0004311 Side Eject Block x 2

D0004591 Side Eject Housing x 2

D0004592 Eject Housing Plate x 2

D0005200 Safety Dead Stop Block x 1

D0005201 Safety Dead Stop Backer (5357) x 1

D0005202 Safety Dead stop Yoke (5358) x 1

D0005203 Safety Slider Cap x 2

H0004626 Shaft 16mm: 275 Eject Push x 4

M0000101 Compression Spring 11 D 15 D 25 Long x 1

P0000035 Cylinder 25x160 x 2

P0000174 Fitting: Plug 1/4'' BSP (Grubscrew Type x 2

P0000201 Flow Controller 6mm x M5 Elbow x 2

P0000367 16mm bore X 125 stroke with rod end clevis x 1

P0000369 Clamp to suit P0000367 x 2

P0000444 Reed Switch: Pneumax 1580U (5.0m Lead) x 2

P0001068 Valve Base: Type 41 2 Position Ø6 x 1

P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1

P0001163 1/4 bsp male silencer x 2

P0001186 Valve/ 5/2 smc x 2

P0001198 1/8 bsp 6mm speed controller x 4

P0000394 reed switch holder x 2

P0000-444 Reed switch pneumax x 2t; P0001068 Valve Base: Type 41 2 Position Ø6 x 1 P0001085 Fitting: SMC 1/4" to Ø8 Swivel Elbow x 1 P0001163 1/4 bsp male silencer x 2 P0001186 Valve/ 5/2 smc x 2 P0001198 1/8 bsp 6mm speed controller x 4 P0000394 reed switch holder x 2 P0000-444 Reed switch pneumax x 2</nowiki>)
R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (<nowiki>'''Tools required&l … '''Tools required'''

Tape rule

Steel rule

standard hex keys

Standard HSS drill set

Standard Tap set

Hack saw

Ball Pein hammer

Centre punch

'''Part Required'''

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 3

P0000024 Fitting: Hex Nipple 1/4 BSP x 1

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000097 Fitting: Elbow Adaptor 8mm - 1/4 BSPT x 1

P0000159 Fitting: Stem Blanking Plug 6mm x 3

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000279 Female Cross 1/4'' NPT x 1

P0000297 HighLow Pressure Valve x 1

P0000419 Air Service Unit OH (P0283)x 1

P0001070 Valve Base: Type 41 6 Position Ø6 x 2

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8

P0001101 Male straight 12mm to 1/4 bsp x 5

P0001102 Male elbow 12mm to 1/4 x 2

P0001186 Valve 24v dc SMC x 12

;P0001070 Valve Base: Type 41 6 Position Ø6 x 2 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8 P0001101 Male straight 12mm to 1/4 bsp x 5 P0001102 Male elbow 12mm to 1/4 x 2 P0001186 Valve 24v dc SMC x 12 </nowiki>)
R0015114 Bench Assemble Valve Banks and Regulators + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard hex key set

Standard spanner set

Standard HSS drill set

Standard tap set

'''Parts Required'''

H0007998 Regulator internal mount 5 way x 1

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14

P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9

P0000021 air gun assembly x 1

P0000024 hex nipple 1/4 x 3

P0000058 Regulator Mounting Kit x 1

P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2

P0000145 tee equal 1/4 x 3

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1

P0000278 Regulator 0-2 bar x 1

P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8

P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1

P0000419 Air Service Unit OH (P0283) x 1

P0001071 Valve base type41 8 position x 1

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4

P0001101 Male straight 1/4 bsp to 12mm x 2

P0001102 Fitting male elbow 12mm 1/4 x 4

P0001105 Bulkhead straight 12mm x 6

P0001186 Valve. 24v dc smc x 8

 P0001071 Valve base type41 8 position x 1 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4 P0001101 Male straight 1/4 bsp to 12mm x 2 P0001102 Fitting male elbow 12mm 1/4 x 4 P0001105 Bulkhead straight 12mm x 6 P0001186 Valve. 24v dc smc x 8 </nowiki>)
R0015316 V notch Final Assembly Part 2 + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard Hex key set

Standard Spanner set

ZX5 Blade tightening tool

Compressed air connection with regulation (for axis support)

'''Parts required'''

A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2

A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2

B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4

B0000173 Blanking plug foc x 28

B0000426 Linear Rail MSB25 400mm Long (AMT) x 4

D0015156 Saw Bearing Plate x 2

D0015161 Saw Plate x 4

D0015162 Saw Mid Spacer Bar x 1

D0015163 Saw Bearing Spacer Bar x 1

D0015168B Balance Cylinder Bracket x 2

D0015169B Cylinder Rod Bracket x 2

D0015179 Energy Chain Bracket x 2

D0015180 Datum Switch Bracket (VZ) x 1

D0015183 VY Stop x 2

D0015235 VY Datum Switch Bracket x 1

D0015236 VY Energy Chain Bracket - Fixed x 1

D0015237 VY Energy Chain Bracket - Moving x 1

D0015250 Safe Sensor Block x 1

D0015251 Safe Sensor Finger x 1

D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2

D0015452 Scissor Cable Retainer x 1

D0015541 Energy Chain Deflector x 1

D0015704 Energy Chain Support Plate x 1

E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2

E0001185 Elte Saw motor x 4

M0001087 Rubber Bump Stop M6 Ø20x24 x2

P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1

P0000023 Fitting: Hex Nipple 1/8 BSP x 1

P0000026 Silencer 1/4 BSP x 1

P0000050 Fitting: Silencer 1/8'' BSP x 1

P0000077 Straight Adaptor 8mm - 1/8BSP x 1

P0000140 Fitting: Quick Exhaust Valve 1/8" x 1

P0001040 Fitting: 1/8BSP Hex Head Silencer x 2

P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2

P0001133 Cylinder: Ø50 x 500 x 2

P0001134 Floating Joint M18x1.5 x 2

P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2

P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1

P0001142 Adjustable Damper 150mm stroke (3000N) x 1

P0001144 Reed Switch Mounting Band for Ø50 cyl x 2

R0015084 Bench assemble and Drill Off Swarf chutes

V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 BJ3-1 x 2 P0001133 Cylinder: Ø50 x 500 x 2 P0001134 Floating Joint M18x1.5 x 2 P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2 P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1 P0001142 Adjustable Damper 150mm stroke (3000N) x 1 P0001144 Reed Switch Mounting Band for Ø50 cyl x 2 R0015084 Bench assemble and Drill Off Swarf chutes V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4</nowiki>)
R0000963E Bench Assemble Z axis Components + (<nowiki>'''Tools Required'' … '''Tools Required'''

Standard hex key set

Standard spanner set

Emery tape

Standard HSS drill set

Hand reamer

Standard tap set

'''Part Required'''

B0000086 Ball Bearing 15 D 32 D 9 Long + seals x 4

B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals x 2

B0000351 Bearing 40mm O/D 17mm I/D 17.5mm Wide x 2

C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1

D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1

D0006501 Z Leadscrew Sleeve x 2

D0007629 Cylinder rod Extension x 4

D0007732 Sprocket Idler Shaft x 2

D0007733 Sprocket Mounting Block x 2

D0008090 Retaining Collar x 1

H0007715 Z Sprocket 33 Teeth 3/8'' pitch x 2

H0007790 Leadscrew Z(Includes Re-balling) x 2

P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 2

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 2

P0000023 Fitting: Hex Nipple 1/8 BSP x 2

P0000024 Fitting: Hex Nipple 1/4 BSP x 2

P0000026 Silencer 1/4 BSP x 4

P0000051 Fitting: Straight Adaptor 6mm - 1/4 BSPT x 4

P0000140 Fitting: Quick Exhaust Valve 1/8" x 2

P0000145 Tee-Equal 1/4BSP Galvanised x 2

P0000200 Elbow Adaptor 6mm - M5 x 2

P0000229 Pneumax VDMA 40 x 300 Magnetic x 4

P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4

P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2

t; P0000140 Fitting: Quick Exhaust Valve 1/8" x 2 P0000145 Tee-Equal 1/4BSP Galvanised x 2 P0000200 Elbow Adaptor 6mm - M5 x 2 P0000229 Pneumax VDMA 40 x 300 Magnetic x 4 P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4 P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2 </nowiki>)
R0015278 Mount Completed Assemblies + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 1 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chain
R0015286 Bench Assemble X axis components and energy chain )
R0015288 Bench Assemble Transfer slider units and Cylinder Rails + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set '''Parts Required''' B0001160 Delrin Dual V Wheel Kit x 48 B0001161 Spacer: Concentric - Delrin Dual V Wheel x 24 B0001162 Spacer: Eccentric - Delrin Dual V Wheel x 24 D0015255 Rack: Mod2 360 Long x 8 D0015551 Rack Mounting Plate x 8 D0015572 Slideway Connection Plate (2018) x 8 D0015573 Transfer Cylinder Bracket x 8 D0015576 Pneumatics Support Spacer x 8 D0015599 Transfer Cylinder Bracket Brace x 8 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 48 P0001111 Cylinder: Ø25 x 25S Cut Shaft x 48 R0015093 Bench Assemble Transfer Beam x 8
S Cut Shaft x 48 R0015093 Bench Assemble Transfer Beam x 8 )
R0015060 Bench Assemble Flapper Beam + ('''Tools Required''' … '''Tools Required''' Standard hex key set Tape measure Steel rule Engineers square '''Parts Required''' B0001099 Bush flange 10 i/d 12 o/d x 14 C0001018 EP2338-0001 EtherCAT Box 8 Configurable IO x 1 D0010167 Ethercat Mount Plate x 1 D0015353 Sensor Flapper Pivot x 8 D0015355 Sensor Flapper Plate (312) x 6 D0015357 Sensor Flapper Plate (270) x 1 D0015363 Sensor Flapper Support Transfer x 1 E0000336L Sensor: M8; 4mm, PNP N/O, M8 conn x 7 F0000537 dowel pin 10 x 40 x 8 M0001016 Angle 74 x 38 x 2 M0001209 Bracket m8 proximity sensor bracket 90 deg x 7 '''Fastener list''' M5 x 6 Grubscrew kcp 8 off 10mm x 40 dowel 8 off M6 x 20 socket cap 8 off M5 D nut 14 off M6 D nut 10 off M8 D nuts 8 off M5 A form washer 7 off M5 x 10 socket cap 7 off M5 x 10 button socket 7 off M3 x 20 panhead 2 off M6 x 16 socket cap 2 off M6 A form washer 2 off M8 x 20 socket cap 8 off M8 heavy motor plate washer 8 off Cable tie bases 7 off
t cap 8 off M8 heavy motor plate washer 8 off Cable tie bases 7 off )
R0015329 Fit Head Spindle Posts + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard flat hand file Emery tape 120 standard hand tap set Stubby hex key set Ratchet/hex bit set Blade flange spanner '''Parts Required''' D0004002 Webb x 1 D0004003 Top Shaft Block x 2 D0004004 Brace Support Bar (D7451) x 1 D0004157 Motor plate spacer x 3 D0004342 Damper Bracket (5312) x 1 D0007451 Brace Support Bar OH (D4004) x 1 D0015490 Saw Turntable Sensor Flag x 1 D0015491 Saw Turntable Flag Bracket x 1 H0004024 Infeed Clamp Post x 1 H0004025 Outfeed Clamp Post (5302) x 1 H0004510 Shaft 30mm: 540 Saw Stroke x 2 P0000055 Adjustable Damper 200mm (Saw Stroke) x 1 R0000560 Bench Assemble Spindle x 1 R0000569E Bench Assemble Head Spindle Posts Mk5 x 1 V0000043B Saw Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1
Blade: Ø500 x 160 teeth x 3.2mm pl x 4mm kf x 30mm bore x 1 )
R0000558E Bench Assemble Base and Turntable Part 2 + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1)
R0015063 Bench Assemble Roller Tables + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Tape measure/Rule 8.2mm HSS drill Drill '''Parts Required''' B0001092 Plastic roller x 48 B0001103 Bush flange x 28 B0001220 Spacer x 28 D0015001 Roller Bed Cylinder Arm x14 D0015002 Shaft 10mm: 58mm Rod End x 14 D0015003 Roller Bed Rail 375mm x 6 D0015004 Roller Bed Rail 550mm x 2 D0015005 Roller Bed Rail 1000mm x 10 D0015006B Roller Bed Arm Bracket x 14 D0015010 Rod End Spacer x 28 D0015283 Saw Infeed Backfence Plate x 5 D0015481 Shaft 8mm: 50mm Cylinder Pivot x 14 D0015547 Sensor Blower Plate x 1 D0015603 Roller Bed Pivot Shaft (silver steel) x 14 D0015608 Saw Infeed Backfence Plate (Full Length) x 5 E0001120 Sensor: Ultrasonic M8 20-150mm x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 14 P0000200 Elbow Adaptor 6mm - M5 x 1 P0001152 Cylinder 25 x 25 x 14 P0001198 Fitting Speed controller 1/8 x 6mm tube x 28 P0000160 flow regulator x1
ontroller 1/8 x 6mm tube x 28 P0000160 flow regulator x1 )
R0015081 Bench Assemble Single Roller Table + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set '''Parts Required''' B0001103 Bush Flange 8 I/D 10 O/D 3.8 Long iglidur J type x 2 B0001154 Plastic Roller Blue Ø30 x 160 Long. Spring Loaded Shafts x 4 B0001168 Bush Sleeve 8 I/D 10 O/D 8L iglidur J type x 2 D0015001 Roller Bed Cylinder Arm x 1 D0015002 Shaft 10mm: 58mm Rod End x 1 D0015006B Roller Bed Arm Bracket x 1 D0015481 Shaft 8mm: 50mm Cylinder Pivot x 1 D0015483 Infeed Loader Roller Bed Mount x 1 D0015594 Roller Bed Rail (Loader Wheel) x 2 D0015603 Roller Bed Pivot Shaft (silver steel) x 1 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 2 P0001110 Cylinder 25 x 10 x 2 P0001198 Air Fitting x 4 x 2 P0001110 Cylinder 25 x 10 x 2 P0001198 Air Fitting x 4)
R0015278 Mount Completed Assemblies Section two + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chainsembly R0015286 Bench Assemble X axis components and energy chain)
R0000558E Bench Assemble Base and Turntable + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1
ainless lock washer x 4 D0015663 SR Axis Motor Guard x 1 )
R0015082B fencing and guards + ('''Tools Required''' … '''Tools Required''' Standard hex key set standard spanner set Standard HSS drill set Standard Tap set 1 meter level Tape measure Steel rule '''Parts Required''' D0008330 Double Door Keep x 2 D0015326 Transfer Gate Upright x 6 D0015333 ZX5 Fence Hinge Spacer x 6 D0015340 Profile Support Plate (Short) x 1 D0015341 Profile support plate mount x 1 D0015349 Safety Hinge Mounting Plate x 6 D0015517 Fence Mounting Section x 28 D0015526 ZX5 Saw Fence Infill x 1 D0015601 ZX5 Saw Fence Support Beam (40x80x550) x 1 D0015606 Fence 10 Support Beam F Slot Fixings. x 2 D0015771 Double Door Keep Spacer x 1 D0015914 Saw Infeed Profile Deflector x 1 D0015962 ZX5 Fence 11 - 1100 x 1850 x 2 D0015963 ZX5 Fence 1 1450 x 1850 x 12 D0015964 ZX5 Fence 3 - 1450 x 1850 Cutout x 1 D0015965 ZX5 Fence 2 820 x 1850 x 1 D0015966 ZX5 Fence 10 927 x 1850 x 2 D0015967 ZX5 Transfer Gate x 3 D0015968 ZX5 Fence 7 642x 1850 extraction holes x 1 D0015969 ZX5 Fence 8 - 1105 x 105 Saw Corner x 1 D0015970 ZX5 Fence 820 x 1105 x 1 D0015972 ZX5 Fence Infill - 65 x 1850 x 1 D0015974 ZX5 Fence 13 - 820 x 1105 Hole for Gate x 1 D0015986 Multi Head Waste Bin Guard x 2 D0016018 ZX5 Saw Cabinet Infill Guard x 1 D0016036 Compliance Guard around Cabinet x 1 D0016037 Compliance Guard - MH to MH Infeed x 1 D0016038 Compliance Guard - MH to MH Out x 1 D0016051 Fence Guard (Crank) x 4 D0016171 Compliance Guard - MH to Transfer Gate x 1 D0016172 Compliance Guard - Saw to Transfer Gate x 1 E0001176 Safety Hinge Switch x 3 E0001177 Hinge (works with E1176 Safety Switch) x 3 F0000299 T Nut Sub Insert M6 (Fat) x 83 M0000029 Cabinet Lock (Triangular) x 4 M0000515 Floor Mouting Angle 200x87x42x 7 M0000516 Adjustable Foot Ø60 M14 x 6 M0001016 Angle 74 x 38 x 6 M0001202 Bruehl Fence Panel 1825 x 2200 x 4 M0001204 Bruehl 2.0m Transit Post x 5 M0001207 Bruehl Fence Clip x 31 R0000901 ZX4 Local Gate x 1
01207 Bruehl Fence Clip x 31 R0000901 ZX4 Local Gate x 1 )
R0015093 Bench Assemble Transfer Beam + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard hand taps V rail alignment Jigs Drill driver and 4mm hex fitting '''Parts Required''' B0001155 OpenRail 1000mm Long x 32 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9
2 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9 )
R0015267 Assemble Backfences, Fit and Align + ('''Tools Required''' Standard Hex Key set Wire Line 150mm Rule '''Parts Required''' D0015420 M/C Infeed Backfence Plate x 9 D0015468 Infeed Backfence Bracket x 9 )
R0015099 Guard panel drilling + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard Hss drill set Standard Tap set Material clamps Clamping blocks Drill Cutting fluid Marker pen Hide hammer '''Parts Required''' D0000330 Rear Chute Panel (500mm) x 1 D0004391E LF Side Sheet Mk5 (5395E) x 1 D0004576E Saw Centre Frame Mk5 (5343E) Standard Hand x 1 D0010967 Saw Mk5 Undertray x 2 D0015238 Saw Top Hood ZX5 x 1 H0004649 Chute Insert Outfeed (5321) x 1 H0004697 Chute Insert Infeed (5322) x 1 H0004751 Ejector Tray Front (5323) x 1 H0004752 Ejector Tray Rear (5324) x 1 H0004846 Right Side Hinged Panel x 1 D0001878 Rear saw door x 1
846 Right Side Hinged Panel x 1 D0001878 Rear saw door x 1 )
R0015358 Conveyor chassis + ('''Tools Required''' … '''Tools Required''' standard hex key set Standard spanner set Standard HSS drill set Standard tap set Utility knife '''Parts Required''' B0000441 Conveyor 3580mm x 300mm x 1 B0001013 Conveyor Motor SEW - WA 10 x 1 B0001177 Pair conveyor side cheeks and bearings slave x 2 M0000133 Conveyor Belt XL-AS 7350 x 300 B x 1 P0000200 Elbow Adaptor 6mm - M5 x 3
AS 7350 x 300 B x 1 P0000200 Elbow Adaptor 6mm - M5 x 3 )
R0000572 Bench Assemble Centralise Assembly + ('''Tools Required''' … '''Tools Required''' standard hex key set Standard spanner set Grease gun '''Parts Required''' B0000005 Angular Contact Bearing 15 I/D 35 O/D 11 Long x 2 B0000065 Bearing Rod End 10mm x 2 D0004363 Middle Link Rod x 1 D0004365 Pivot Clamp x 1 D0004366 Link Clamp Cap x 1 D0004369 Top Link Stud Bolt x 1 D0004370 Middle Link Stud Bolt x 1 D0004393 Lever Joint x 2 D0004394 Joint Shaft x 2 D0004401 Pivot Pin x 1 D0004403 Pivot Pin Nut x 1 D0004406 Retainer Plate x 1 D0004541 Cylinder Swivel End x 2 D0004542 Cylinder Bracket 4542 x 1 D0004622 Centralise Cylinder Spacer x 1 D0004669 Damper Rod End Block x 1 D0004766 Pivot Pin Bolt x 1 H0004367 Centering lever x 1 P0000029 Non Adjustable Damper 100mm x 1 P0000031 Pneumax Microcylinder 25 x 100 Magnetic x 2 P0000049 Cylinder Spherical Bearing M10 x 1.25 x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 2 P0001198 fitting speed controller 1/8 x 6mm tube x 2
) x 2 P0001198 fitting speed controller 1/8 x 6mm tube x 2 )
R0015263 Mount drive motor for load shaft + ('''Tools Required''' S … '''Tools Required''' Standard Hex key set Standard Spanner set Long nose pliers '''Parts Required''' B0000041 Feather Key 5 x 5 x 18 Long x 1 B0000142 Feather key 5 x 5 x 25 long B0000240 Geared Motor 0.18kW 18RPM Motovario x1 B0001100 Feather Key 8 x 7 x 30 Long x2 D0006714 Index Torque Limiter (B0189 / B0190) x1 D0015460 Infeed Motor Shaft (2018) x1 D0015461 Infeed Motor Mount x1 D0015462 Infeed Motor Platex1 F0000618 m10 x 70 set boltunt x1 D0015462 Infeed Motor Platex1 F0000618 m10 x 70 set bolt)
R0015037 Bench Assemble SY Assembly Part 2 + ('''Tools Required''' S … '''Tools Required''' Standard Hex Key set Standard Spanner set 1 Meter straight edge Feeler Gauges '''Parts Required''' B0000044 Linear Rail MSB25 260mm Long (AMT) x 2 B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4 B0000173 blanking cap x 10 B0000234 Straight Grease Nipple M6 ST/ST x 4 B0000245 Needle Bearing 12 D 16 D 10 Long (ENA) x 12 B0001060 Grease Fitting M6x0.75 to Ø4 x 4 B0001061 Grease fitting M6 x 1 to 4mm x 4 B0001123 Double angular contact bearing 6 I/D 17 O/D 9 long x 2 B0001185 Leadscrew nut Igus x 1 C0001005 Stepper Motor AS1050 x 1 D0005184 Guide Roller x 6 D0005186 Guide Pin Washer x 6 D0015172 Centralise Plate (with SY) x 1 D0015173 Saw SY Saddle Brace x 1 D0015174 Roller Fence (With SY) x 2 D0015175 Saw Saddle Carriage Block x 2 D0015176 Cylinder Mount Block x 2 D0015178 Z Block x 2 D0015207 Outer Bearing Housing x 1 D0015208 Leadscrew Bearing Block x 1 D0015209 Leadscrew Attachment Bracket x 1 D0015222 SY Grease Manifold x 2 D0015240 Collar Clamp: SY Axis ZX5 x 1 D0015316 Leadscrew Bearing Block Cover x 1 D0015415 Turret Pickup Arm ZX5 x 2 D0015416 Bracket: Turret Stop RH ZX5 x 1 D0015417 Bracket: Turret Stop LH ZX5 x 1 D0015698 Flag Block x 1 D0015777 Leadscrew SY x 1 D0016336 SY table blower x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 H0005185 Shaft 12mm: 90.5 Saw Fence Roller Pin x 6 M0001209 Bracket m8 proximity sensor 90 degree x 1 P0000200 Elbow Adaptor 6mm - M5 x 7 P0001127 Guide cylinder 20 x 30 compact x 2 P0001157 Turret Stop: 6 Station Right Handed Somatec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1matec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1)
R0015064 Bench Assemble Clamp Assembly Part 2 + ('''Tools Required''' S … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers 20mm bearing dolly Reduced shank 5mm hex key '''Parts Required''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 8 B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8 B0000200 Circlip 8mm External x 12 B0000346 Ball Bearing 8 D 22 D 7 Long + seals x 6 D0004331 Clamp Head (D7450) x 1 D0004332 Clamp Mount Block (D7449) x 1 D0004333 Pillar x 2 D0004358 Clamp Head Bracket (D7447) x 1 D0004359 Clamp Head Cylinder Bar (D7446) x 2 D0004550 Clamp Insert x 2 D0004808 Slide Stop x 2 D0005191 Bearing Protective Washer x 4 D0005425 Clamp block Right (5625) x 1 D0005566 Clamp block left - Roller style (5567) x 1 D0005568 Clamp block left roller shaft x 3 D0007447 Clamp Head Bracket OH (D4358) x 1 D0007449 Clamp Mount Block OH (D4332) x 1 D0007450 Clamp Head OH (D4331) x 1 D0015266 Shaft 38.7mm: 440mm ZX Saw Top Clamp BZP x 2 D0015299 Shaft 16mm: 320mm Chip Deflector ZX5 x 1 D0015446B Chip Deflector Mounting Plate (Tapped) x 1 D0015447B Chip Deflector Probe Ø50 (Tapped) x 2 D0015454 Chip Deflector Rod (M16) x 2 H0004625 Shaft 16mm: 150 Saw Clamp x 2 H0004626 Shaft 16mm: 275 Eject Push x 1 H0004627 Shaft 20mm: 210 Saw Inner Clamp x 2 H0004628 Shaft 20mm: 245 Saw Outer clampx 2 M0001194 Kipp clamp handle x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000054 Cylinder Ø32 x 50 (PIS32A50) x 1 P0000064 Pneumax microcylinder 25bore x 80stroke x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1)
R0000571 Fit and Level Cut Tables , Finalise Eject + ('''Tools Required''' … '''Tools Required''' 1 meter straight edge 500mm rule Standard hex key Standard spanner set Feeler gauges Engineers level Adjustment shim '''Parts Required''' A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 0.5 A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 1 A0001074 igus mounting bracket set x 1 D0004551 Cylinder Spacer x 1 D0004553 Cover Fixing Bar x 1 D0004554 Bar Spacer Short x 1 D0004555 Bar Spacer Long x 1 D0004769 Ejector Clamp Pad to be made in conjuction with D5121 (5305) x 1 D0004770 Infeed Clamp Pad to be made in conjunction with D5122 (5299) x 1 D0005121 Ejector Clamp Stainless Pads (5306) x 1 D0005122 Infeed Clamp Pad (5300)x 1 D0005199 Ejector Cover x 1 D0005412 Energy Chain Adapter Plate x 1 H0004556 Fixing Bar Gap Cover (5297) x 1 H0004656 Material Trip Stripx 1 P0000368 Extension 1/8 bsp x 22 long x 1 P0000443 Cleanline Cylinder 32 x 450 PN11246 x 1 P0000444 Reed Switch: Pneumax 1580U (5.0m Lead) x 2 P0001198 flow controller 6mm elbow 1/8 x 2580U (5.0m Lead) x 2 P0001198 flow controller 6mm elbow 1/8 x 2)
R0015298 Bench Assemble V notch Clamps + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard Spanner set External circlip pliers '''Parts Required''' B0000415 Ball Bearing 20 I/D 32 O/D 7 Long + shields (INA) x 8 B0001176 Washer : bearing shim x 9 D0001313 Datum Roller (Radial Bearing) x 2 D0010060 Roller Shaft Ø20 x 37.5 x 3 D0010061 Datum Roller Ø40 x 20 x 3 D0010065 Shaft 16mm: 115mm Autoflow Infeed Roller x 2 D0010066 Infeed Roller Connector x 1 D0010545 Infeed Roller Mount x 2 D0010546 Infeed Roller Attachment x 1 D0015211 Outfeed Clamp Upright x 2 D0015212 Top Clamp Mounting Plate x 1 D0015213 Side Clamp Mounting Block x 1 D0015221 Outfeed Roller Bed Mounting Plate x 1 D0015241 Outfeed Side Clamp Mounting Block x 1 D0015242 Outfeed Front Fence x 1 D0015243 Outfeed Top Clamp Plate x 1 D0015244 Outfeed Top Clamp Mounting Plate x 1 D0015245 Outfeed Top Clamp Leg x 2 D0015246 Centre Side Clamp Roller Block x 1 M00001004 Endcap 40 x 40 black x 2 M0001006 Threaded insert M14-M8 30 long x 4 M0001017 Endcap 80x40 Black x 2 P0000010 6mm elbow x 4 P0001045 Guide cylinder 25 x 150 x 2 P0001132 Cylinder 32x 175 guided x 2 P0001198 Fitting: Speed controller 1/8" x 6mm Elbow x 4
P0001198 Fitting: Speed controller 1/8" x 6mm Elbow x 4 )
R0000962E Bench assemble Y axis Components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Fine emery tape solvent Standard drill set '''Parts Required''' B0000086 Ball Bearing 15 D 32 D 9 Long + seals x 2 B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals x 1 B0000236 90 Deg Grease Nipple M6 ST/ST x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1 D0006488 Y Leadscrew Sleeve x 1 H0007789 Y Leadscrew x 1
0006488 Y Leadscrew Sleeve x 1 H0007789 Y Leadscrew x 1 )
R0015064 Bench Assemble Clamp Assembly + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers 20mm bearing dolly Reduced shank 5mm hex key '''Parts Required''' B0000033 Linear Bearing: Ø20 x 30 Compact (Metal Case Only) x 8 B0000034 Linear Bearing: Ø16 x 30 Compact (Metal Case Only) x 8 B0000200 Circlip 8mm External x 12 B0000346 Ball Bearing 8 D 22 D 7 Long + seals x 6 D0004331 Clamp Head (D7450) x 1 D0004332 Clamp Mount Block (D7449) x 1 D0004333 Pillar x 2 D0004358 Clamp Head Bracket (D7447) x 1 D0004359 Clamp Head Cylinder Bar (D7446) x 2 D0004550 Clamp Insert x 2 D0004808 Slide Stop x 2 D0005191 Bearing Protective Washer x 4 D0005425 Clamp block Right (5625) x 1 D0005566 Clamp block left - Roller style (5567) x 1 D0005568 Clamp block left roller shaft x 3 D0007447 Clamp Head Bracket OH (D4358) x 1 D0007449 Clamp Mount Block OH (D4332) x 1 D0007450 Clamp Head OH (D4331) x 1 D0015266 Shaft 38.7mm: 440mm ZX Saw Top Clamp BZP x 2 D0015299 Shaft 16mm: 320mm Chip Deflector ZX5 x 1 D0015446B Chip Deflector Mounting Plate (Tapped) x 1 D0015447B Chip Deflector Probe Ø50 (Tapped) x 2 D0015454 Chip Deflector Rod (M16) x 2 H0004625 Shaft 16mm: 150 Saw Clamp x 2 H0004626 Shaft 16mm: 275 Eject Push x 1 H0004627 Shaft 20mm: 210 Saw Inner Clamp x 2 H0004628 Shaft 20mm: 245 Saw Outer clampx 2 M0001194 Kipp clamp handle x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000054 Cylinder Ø32 x 50 (PIS32A50) x 1 P0000064 Pneumax microcylinder 25bore x 80stroke x 2 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1
etal type) x 3 P0001143 cylinder 32 x 175mm stroke ISO x 1 )
R0015046 Bench Assemble Infeed Clamps + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set External circlip pliers Grease for lubrication M0000494 '''Parts Required''' B0000062 Circlip 20mm External x 2 B0000070 Linear Bearing: Ø25 x 40 Compact (Metal Case Only) x 8 B0001176 Washer :bearing shim x 3 D0000209 Shaft Strap (D8709) x 1 D0000211 Cylinder Extension x 1 D0001331 Roller Ø40 x 27 c/w bearing x 3 D0001334 Roller Ø40 x 102 c/w bearing x 2 D0003108 Shaft 20mm: 146mm Clamp Roller Shaft x 2 D0003788 Z Roller Pin (40mm) x 3 D0007680 Infeed Rail x 1 D0007774 Top Roller Block x 1 D0007792 Z Roller Block (D8711) x 1 D0007793 Z Roller Plate (D8710) x 1 D0015427 MC Hold Clamp Bar x 1 D0015428 Top Clamp Block Ø30 15 x 1 H0007773 Shaft 25mm: 268mm ZX Infeed Clamp Top x 2 H0007791 Shaft 25mm :250mm ZX Infeed side x 2 P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 1 P0000010 elbow 6mm 1/8 fitting x 1 P0000200 Elbow Adaptor 6mm - M5 x 2 P0000484 Cylinder 32 x 100 stroke x 1 P0001160 Cylinder 32 x 70 stroke x 1 P0001198 Fitting: flow control 1/8 x 6mm elbow x 4 M0000253 anti slip pad 22mm x 1
rol 1/8 x 6mm elbow x 4 M0000253 anti slip pad 22mm x 1 )
R000569E Bench Assemble Head Spindle Posts + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set Internal circlip pliers Consumable 4mm yellow grease line Pneumatic pipe cutters '''Parts Required''' B0000002 Bearing: 12/28dia x 8mm Sheilded x 2 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001061 Grease fitting x 6 D0004001 Head Bearing Block x 3 D0004021 Upstroke Plate x 1 D0004078 Motor Plate (5311) x 1 D0004099 Cylinder Bearing Block x 1 D0004256 Cylinder rod bar x 1 D0004343 Lower Damper Bracket (5313) x 1 D0004445 Semi circular slit strip (5533) 500mm x 1 D0004634 Chute Sawblade Strip 500mm (5532) x 1 D0004733 Belt Adjuster Pulley x 1 D0004734 Belt Adjusting Bar x 1 D0004735 Belt Adjuster Pin x 1 D0010780 Grease Manifold x 1 H0004444 Semi-circular Guard (5332) x1 P0000009 Fitting: 1/4 BSPT - 6mm Elbow x 2 P0000037 Magnetic Cylinder 40 x 185 with 15mm rod extension x 1 P0000308 Flow Controller In Line 6mm x 1
rod extension x 1 P0000308 Flow Controller In Line 6mm x 1 )
R0002916 Install Machine Trunking + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set Standard tap set Disc cutter '''Parts Required''' A0000068 Top lid gusset 50x50 bend 90° Armorduct x 4 A0001065 wire basket x 0.5 A0001061 Retainer: Wire Basket Cable Tray x 2 D0000301 M/C centre trunking front lower ZX4 x 1 D0000305 M/C centre trunking rear lower ZX4 x 1 D0000306 M/C centre trunking infeed lower (D8736) x 1 D0000307 M/C centre trunking infeed front offset x 1 D0000308 M/C centre trunking infeed rear offsetx 1 D0000309 M/C centre trunking outfeed front offset x 1 D0000313 M/C centre trunking outfeed rear offset x 1 D0000324 M/C centre trunking outfeed front upper x 1 D0000325 M/C centre trunking infeed front upper x 1 D0000326 M/C centre trunking front drop x 2 D0000327 M/C centre trunking outfeed lower x 1 D0000329 M/C centre trunking infeed rear end x 1 D0000694 M/C centre trunking outfeed rear end x 1 D0007996 Trunking support pillar x 1
outfeed rear end x 1 D0007996 Trunking support pillar x 1 )
R0015037 Bench Assemble SY Assembly + ('''Tools Required''' … '''Tools Required''' Standard Hex Key set Standard Spanner set 1 Meter straight edge Feeler Gauges '''Parts Required''' B0000044 Linear Rail MSB25 260mm Long (AMT) x 2 B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4 B0000173 blanking cap x 10 B0000234 Straight Grease Nipple M6 ST/ST x 4 B0000245 Needle Bearing 12 D 16 D 10 Long (ENA) x 12 B0001060 Grease Fitting M6x0.75 to Ø4 x 4 B0001061 Grease fitting M6 x 1 to 4mm x 4 B0001123 Double angular contact bearing 6 I/D 17 O/D 9 long x 2 B0001185 Leadscrew nut Igus x 1 C0001005 Stepper Motor AS1050 x 1 D0005184 Guide Roller x 6 D0005186 Guide Pin Washer x 6 D0015172 Centralise Plate (with SY) x 1 D0015173 Saw SY Saddle Brace x 1 D0015174 Roller Fence (With SY) x 2 D0015175 Saw Saddle Carriage Block x 2 D0015176 Cylinder Mount Block x 2 D0015178 Z Block x 2 D0015207 Outer Bearing Housing x 1 D0015208 Leadscrew Bearing Block x 1 D0015209 Leadscrew Attachment Bracket x 1 D0015222 SY Grease Manifold x 2 D0015240 Collar Clamp: SY Axis ZX5 x 1 D0015316 Leadscrew Bearing Block Cover x 1 D0015415 Turret Pickup Arm ZX5 x 2 D0015416 Bracket: Turret Stop RH ZX5 x 1 D0015417 Bracket: Turret Stop LH ZX5 x 1 D0015698 Flag Block x 1 D0015777 Leadscrew SY x 1 D0016336 SY table blower x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 H0005185 Shaft 12mm: 90.5 Saw Fence Roller Pin x 6 M0001209 Bracket m8 proximity sensor 90 degree x 1 P0000200 Elbow Adaptor 6mm - M5 x 7 P0001127 Guide cylinder 20 x 30 compact x 2 P0001157 Turret Stop: 6 Station Right Handed Somatec x 1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1
1 P0001158 Turret Stop: 6 Station Left Handed Somatec x 1 )
R0015035 Bench Assemble V Notch Components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set Vernier 150mm 2 meter straight edge 40mm shaft pin jigs Feeler gauge set Internal circlip pliers External circlip pliers 8mm hand reamer '''Parts Required''' B0000041 5 x 5 x 19 key x 1 B0000109 Linear Bearing (IKO) 40 D x 62 D x 80 L x 8 B0000427 Leadscrew Ø25x10 435 Long x 1 B0001047 Fixed Bearing Support Block Ø17 x 1 B0001120 Circlip 62mm External x 16 B0001127 ROTEX GS Coupling Ø14/Ø15 Bore & Key (98 Shore Spider) x 1 B0001134 Ball Bearing 15ID 35OD 11 Long x 10 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 D0010132 SZ Drive Mount Plate x 1 D0010563 Y Axis Servo Mount x 1 D0015147 V Notch Upper Support Bar x 1 D0015148 V Notch Lower Support Bar x 1 D0015149 VZ Shaft End Plate x 4 D0015152 V-Notch Upper Moving Bar x 1 D0015153 V-Notch Rear Moving Bar x 1 D0015154 V-Notch Front Moving Barx1 D0015157 Saw Motor Bar x 4 D0015158 Shaft 40mm: 190mm ZX V Notch Saw Motor Slide x 8 D0015159B Saw Motor Adjustment Screwx 4 D0015160 Saw Motor Block x 4 D0015164 VY Leadscrew Block x 1 D0015166 VY Motor Mounting Plate x1 D0015258 Upper Link Mount 1 x 1 D0015259 Upper Link Mount 2 x 1 D0015260 Upper Link x 2 D0015261 Lower Link x 2 D0015262 Lower Link Mount x 2 D0015263 Mid Link Shaft x 2 D0015264 Lower Link Shaft x 2 M0001093 Shaft Clamping Element (Ø15-20 shafts) x 16
haft x 2 M0001093 Shaft Clamping Element (Ø15-20 shafts) x 16 )
R0000706 Bench assemble Infeed Datum rollers + ('''Tools required''' … '''Tools required''' External circlip pliers Standard hex key set Pipe cutters Pneumatic identification numbers '''Parts Required''' B0000062 Circlip 20mm External x 6 D0001176 Washer : bearing shim x 3 D0001333 Roller Ø40 x 80 c/w bearing x 3 D0001334 Roller Ø40 x 102 c/w bearing x 3 D0003108 Shaft 20mm: 146mm Clamp Roller Shaft x 3 D0007677 Infeed Base Rail (D2972) x 1 D0007942 Shaft 20mm: 119.4mm ZX Datum Roller Circlip x 3 D0010896 Infeed Clamp Blower Vert x 1 D0010897 Infeed Clamp Blower x 1 P0000053 6mm T (P16) x 1 P0000160 Fitting: Flow Controller In Line 6mm x 16mm T (P16) x 1 P0000160 Fitting: Flow Controller In Line 6mm x 1)
Stuertz Infeed - Freeing Roller under Gripper Arm + ('''Applies to: A2026-A2030 Autoflow Mk4 wi … '''Applies to: A2026-A2030 Autoflow Mk4 with Jetta Locking motors''' In certain circumstances, the forward clamp roller arm has stuck itself under the gripper arm. Freeing from this situation requires a set process because the GZ axis motor is braked and probably in an overload condition

...You need to be confident in using TwinCAT on the VM machine to navigate to settings

nfident in using TwinCAT on the VM machine to navigate to settings</div> </div> )
Laser Setup on Flowline/ZX3 for Laser Holes + ('''How to Setup .''' This will Cover the … '''How to Setup .''' This will Cover the Basic Alignment of the receiver and Sender setup. Focusing the Laser and Setting up the Receiver Sensitivity. Always Make sure Laser Sender and Receiver are clean and both lenses have been wiped with a soft cloth first.
en wiped with a soft cloth first. )
GY GZ axis setup with Jetter Motors + ('''WARNING:''' '''The Jetter motor on th … '''WARNING:''' '''The Jetter motor on the GZ axis has a brake. Releasing the brake without control could be harmful/dangerous.''' '''Use the Air Counterbalance rig to assist if necessary.''' This assumes that the motors are connected to the Beckhoff drive and are free to move.o the Beckhoff drive and are free to move.)
TB0409 Setting Up Windows 10 PC 2018 + (<div class="icon-instructions caution-i …

...Since 2023, the PCs have been supplied with a preconfiguration tool.

Please use [[Setting Up Windows PC C0000422-KIT 2023]][[Setting Up Windows PC C0000422-KIT 2023]])
Commissioning a Beckhoff Axis + (<div class="icon-instructions dont-icon"> <div class="icon-instructions-icon"></div> <div class="icon-instructions-text">...Any stepper motor drives will need the EP7041 drive to be programmed first</div> </div>)
R0015066 Bench Assemble Saw Motor Assembly + ('''Tool Required''' … '''Tool Required''' Standard hex key set Standard spanner set Cutting disc Standard hand taps '''Parts Required''' A0000013 32mm Conduit Adaptorx 1 A0000027 Flexible Conduit Ø32mm x 1 D0004079 Saw Motor (Modified Front Flange) x 1 D0004437 Motor Conduit Bracket x 2 D0004835 Flex conduit plate x 1 D0004997 Connector Support Block (5360) x 1 D0004999 Reed Switch Terminal Box x 1 D0005219 Turntable Nozzle x 1 D0008198 Chute Flap x 1 H0008200 Chute Flap Bracket x 1 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1
1 P0000295 Elbow Adaptor 6mm - 1/8 BSPT (Metal type) x 1 )
R0015271 Mount buffer bars + ('''Tools Required''' … '''Tools Required''' Standard Hex key set '''Parts Required''' D0015463 Infeed Front Endfence x1 D0015464B Infeed Rear Endfence x 1 D0015465 Endfence Spacer - Short x 3 D0015466 Endfence Spacer - Long x 3 D0016335 light curtain mounting post x 1ence Spacer - Long x 3 D0016335 light curtain mounting post x 1)
R000718E Stage 2 spindle assembly + ('''Tools Required''' … '''Tools Required''' 0.05mm feeler gauge Standard hex key set Standard spanner set Rule 6mm punch Ball pien hammer '''Parts Required''' D0007990 cylinder anchor x 7 D0007648 end plate x 4 D0007649 Double slide end plate x 4 D0007686 single motor plate x 4 D0007723 Double slide motor mount x 4 D0007687 Motor mount x 4 D0007600 Cylinder anchor x 4 D0015856 hard stop x 4
t x 4 D0007600 Cylinder anchor x 4 D0015856 hard stop x 4 )
R0015335 Mount Electrical Cabinet + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Standard HSS drill set Standard Tap set '''Parts Required''' D0004391E Left hand side sheet x 1 D0015425 Bracket: Beckhoff Box Right Angle x 1 D0015426 Mounting Plate: Airgun Assy x 1 D0015425 Beckhoff right angle mounting plate x 1 P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 1 P0000021 Airgun Assembly x 1 P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2 P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1 P0000278 Regulator 0-2 bar x 1 P0000373 Regulator fixing bracket x 1 R0015016C Electrical cabinet wiring Mod F
xing bracket x 1 R0015016C Electrical cabinet wiring Mod F )
R0015317 Install Rotary Ring + ('''Tools Required''' … '''Tools Required''' Standard Hex Key set Standard spanner set Lifting Strop Overhead crane operation Torque wrench Soft hammer Ring lubrication oil '''Parts Required''' A0000309 Domed Blanking Plug 19mm x 3 C0001123 Servo Motor: Beckhoff AM8062 18Nm 3000rpm x 1 D0000263 Stop Y Central x 1 D0002990E Strike Post ZX4 Mk5 x 1 D0002991 Switch carrier x 1 D0006061 Timing Belt cap x 1 D0007861 Y axis hard stop x 2 D0010756 Proximity Switch Mounting Block Reduced Size x 2 D0010894 Ethercat Cover ZX3/ZX4 x 1 D0015542 R Axis Motor Connector Cover x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2 H0007995 Rotary base cover plate x 2 M0000451 Plug and Elbow x 2 R0000971E Bench Assemble R Axis Gearbox R0010260 Bench Assemble Tool Break Sensor R0015138 Machining Head ZX4 Mk5 (Quad Plunge)
Break Sensor R0015138 Machining Head ZX4 Mk5 (Quad Plunge) )
R0015325 Mount Infeed Clamp + ('''Tools Required''' standard hex key set '''Parts Required''' R0015046 Bench Assemble Infeed Clamps)
R0015265 Mount Infeed arm covers and End guards + ('''Tools required''' Standard hex key set '''Parts Required''' A0000307 Domed Blanking Plug 32mm D0015457 Infeed Arm End Cover D0015518B Infeed Arm Guard )
TB0428 Connecting To Yaskawa with Silex USB + (== What is the Silex DS-510? == The Silex … == What is the Silex DS-510? == The Silex unit is a USB server, allowing a PC to have a USB port anywhere over an ethernet network. This is useful to connect the PC to a Yaskawa inverter when they are located in different cabinets. The software sets up a virtual USB port which can then be used to run the Yaskawa DriveWorks software.ed to run the Yaskawa DriveWorks software.)
Monday - Getting Started For Engineers + (==Why Change?== *mHelpdesk limitations ** … ==Why Change?== *mHelpdesk limitations **Cludgy to use **Slow response **Cannot connect to other apps or emails *Monday advantages **Easier and more elegant to use **More configurable **easy to email into **Better searching **Expandable to whole business **Cheaper ==Similarities to mHELPDESK== *Monday consists of a set of user definable “Boards” that contain a list of “Pulses”. *The “pulses” can be configured however we like. *I have created a “Board” called “Service Jobs” *On the Service Jobs Board, I have designed the “Pulses” to mimic the service jobs, so this will include the machine, the status, the type classification, etc *Any pulse has associated “Updates”. These are just like the “items” on an mHelpDesk job, but is much more flexible than the plain text of mHelpdesk *The service team will assign jobs as before *The job should be updated by yourself during your visit *The database of jobs is searchable so you can find the machine history
so you can find the machine history )
Saje uPVC Unloading Process + (Access for machinery is limited at the Saj … Access for machinery is limited at the Saje factory. The machine will be delivered in the following modules, that should be unloaded from the lorry in this order #Electrical Cabinet #Machining centre base module (1.8 x 2.2m) #Infeed module (2.4 x 9.0m)
x 2.2m) #Infeed module (2.4 x 9.0m) )
Correcting Linearity with Rack Offset File + (Accuracy problem on A2001 was traced to a … Accuracy problem on A2001 was traced to a non-linear rack. This tutorial demonstrates how to test the linearity of a rack and the systems in place to correct the linearity.

Modifying the linearity of a rack is a very complex and sensitive issue. You must be absolutely certain that there is a case for linearity with REPEATED tests that produce the same result. It is far more likely that accuracy problems are cause by other mechanical issues. This is the only machine in the 20 year history that has needed these alterations

machine in the 20 year history that has needed these alterations</div> </div>)
ZX5 - ZX3 Hepco alignment Module E Saw Infeed + (Alignment and check procedure for mounting … Alignment and check procedure for mounting of hepco rail To main frame Parts required B0001102 hepco rail D0015492 5 off vertical adjustment plate D0015493 5 off Lateral adjustment plate D0015072 1 off Carriage Plate B0000184 journal wiper 4 off B0000185 journal 2 off B0000186 journal 2off Hepco Levelling Jig Hepco rail v block jigs Hepco rail Drive rack pitching jigk jigs Hepco rail Drive rack pitching jig)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Alignment criteria and steps for correct machine installation)
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Alignment details and level settings for correct alignment of module B to module C)
R0000728 R0000729 Stroke Assembly Dismantling + (Assemblies fitted to MK1 ZX4 will require … Assemblies fitted to MK1 ZX4 will require refurbishment at some point of life cycle. The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools Required''' Standard hex key set Standard spanner set Double pin saw flange spanner Drifts and punches Ballpein hammer Soft hammer Degreasing bath
pein hammer Soft hammer Degreasing bath )
Saw machining centre alignment and level check points + (Bullet pointed checks to determine correct alignment of key components within Sawing unit)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Details and steps for correct alignment of Module A to Module B '''Tools Required''' Laser Level 300mm rule 1 meter yellow level 24mm spanner Permanent marker Pipe cutters Ring main connection equipment)
ZX5 Production R0000548E Module G to R0015040 Module F alignment + (Details for correct alignment of module G to module H To include fitting of front safety tray once module G is installed)
Installation Procedure - Autoflow Mk4 + (General Procedure is * Prepare Area * Unload from Transport * Locate and level infeed table * Locate, level and align machining module * Locate, level and align outfeed table * Fix to floor * Locate waste conveyor system * Guard fencing assembly)
Commissioning - Off-Cut Laser Sensor + (Infeed Off-Cut Laser sensors are used to c … Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.be larger that the final triggered sensor.)
Ecoline Site Installation Guide + (Installation of an Ecoline is quite straig … Installation of an Ecoline is quite straight-forward as all of the main levelling and alignment is taken care of inside the main module housing. Installation involves 3 steps # Levelling main module # Attaching and Levelling Infeed Frame # Refitting Infeed coverling Infeed Frame # Refitting Infeed cover)
Monday - Putting Customer Machines On Stop + (It is important that everyone does this th … It is important that everyone does this the same way or confusion and frustration will follow. It is also important to understand how the relationship between a Machine and it’s contract works * Each machine on the “Machine” board needs to link to a “Contract” on the “Service Contracts” board * This allows multiple Machines to have the same “Contract” – eg Customade group contract * The “Contract” is the electronic version or equivalent to the bit of paper that the customer has signed, and contains the start and end dates, etc * For machines that have no contract, I have set up some other “General” contract types. These General Types are not machine specific – ** PAYG – General Pay as you go ** OnStop – Customer is on stop and nothing should be supplied ** AskFirst – Ask KG or management first before supplying goods and services ** Proforma – Payment required before supply of goods and services ** PreDelivery – Before warranty startses ** PreDelivery – Before warranty starts)
Stuertz Infeed - Check GY Position Parallelism + (It is important that the parallelism of th … It is important that the parallelism of the GY axis to the backfence is set and maintained along the length of the rack. This tutorial describes how to check this parallelism without the need for measuring equipment Potential Symptoms of a problem *Gripper cannot pick up offcuts *Gripper /profile end forced away from backfence *Accuracy problems *Gripper wobbles after it has released profile Use the laptop to enable you to control the Service screen whilst inside the infeed table

...You will be inside the danger area of the machine - ensure operators are aware of your situation

Ther gripper setting jig is used to give an accurate and reliable zero to locate the gripper jaw to. Any piece of aluminium reinforcing box section will also work Create a spreadsheet or a table to log your results,.
ng box section will also work Create a spreadsheet or a table to log your results,. )
Setting Motor Overload Relays + (It is important to set the Motor Overload … It is important to set the Motor Overload Relays to the correct values according to the motor as if the current is set too low, the motor will continually trip the MCB and if it set too high then the motor will not trip the MCB under fault conditions, leading to the motor burning out.ditions, leading to the motor burning out.)
Move SR Datum Sensor to Higher Level R0019217 + (On a Mk4 Autoflow, The SR axis daum sensor … On a Mk4 Autoflow, The SR axis daum sensor is originally located at the rear and to the base of the SR axis. This area is prone to offcuts, so a new location has been designed at the top, with the following design parameters *Easy to retrofit *Sensor is protected in a case *Short distance to connection box *Uses existing mounting holes *Easy to adjust and maintain *Sensing end location should be vertical onto a plate, not horizontal on to a radiused surface *Can use E0000336 2mm range sensor reliably *Incorporate a front fence to help deflect offcuts down the chute and to protect the sensor The parts are supplied in Kit R0019217B

...In November 23, a second iteration of the design was released using metal parts and a side fence to improve robustness (R0019217B)

...The pictures and models illustrated here are from a Right to Left feed machine. Parts are unhanded so can be fitted to either hand machine

illustrated here are from a Right to Left feed machine. Parts are unhanded so can be fitted to either hand machine</div> </div> )
Replacing Baldor Microflex Drive with RS Automation + (The Baldor Microflex drive with Beckhoff m … The Baldor Microflex drive with Beckhoff motor was a drive system combination that has now been superseded with a better performance system using an RS Automation Drive and motor combination The Part number for the upgrade is R0019052X Kit: X Axis Replacement using RS Automationit: X Axis Replacement using RS Automation)
Beckhoff AX8000 Flowline Upgrade + (The Flowline range (Mk3, ZX3, ZX4) are Stu … The Flowline range (Mk3, ZX3, ZX4) are Stuga built and designed machines for prepping and cutting uPVC windows and doors. The Flowline is the first machine of the Stuga 'U' shaped machines which has prepping and cutting working in the same machine package. The Flowline is still a fantastic machine for the industry, however, due to the age of the machines and older control systems becoming obsolescent, we have had to find an upgrade route that does not only keep the machine going, but also provides improvements from the original model and up-to-date technology to future proof the machine. The upgrade that we have developed for the Flowline is supplied from an automation supplier named Beckhoff. We also use Beckhoff on our new build machines. This gives us better lead times, more understanding of the products and better diagnostics/ support for our customers. The drive system that we use is called the AX8000 series. These drives are a compact multi axis servo system that use an EtherCAT interface and STO safety functions. These servo drives, coupled with Beckhoff AM8*** series OCT servo motors provide quicker installations and all round performance increases from any system we have previously used. To drive all of the new system, we are using a Beckhoff IPC controller that runs TwinCAT 3. This links into the system via EtherCAT. All of the machine can now link together via EtherCAT to provide quick and stable communications. This tutorial will give you step by step guides on the physical upgrade requirements needed when upgrading a Flowline Mk3 to a Flowline Mk3 with Beckhoff AX8000 Control. Each step will provide you with written information and pictures to guide you through the upgrade. Each step will contain necessary information which will also provide you with rationale for the design and an idea of the benefits over using different methods. Please always feel free to provide Stuga with any feedback on this document or its contents.feedback on this document or its contents.)
GE Control Components Changeover + (The GE control components are now obsolete … The GE control components are now obsolete and we have had to find a new manufacture to use. We have decided to go with Eaton control equipment for this. We are using the same supplier for these products and we have the added benefit if the supplier holding these parts in there stores. We had a choice to use either ABB, Eaton or Schneider components. Although all of the individual Eaton components are a direct replacement for the GE components, there are certain situation that we may be tripped up. This includes times when we need to change a motor breaker that has an auxiliary block connected to it. We can change the breaker but the GE auxiliary block will not fit on the new Eaton one. This means that the Eaton components need to have different part numbers to the GE components. This document will layout the new part numbers and what they relate to and instructions on how they are added and changed in the Sage system. are added and changed in the Sage system.)
ZX5 MH Infeed Basic IO Test and Setup + (The MH infeed on a ZX5 is a module which c … The MH infeed on a ZX5 is a module which can be tested individually away from the fully installed machine. Once build stage is complete, to be able to test individually, the Infeed Module needs: - To be connected to mains power & be powered on - An air supply to the main blue line - Network connection (Network Cube) - HDMI & Keyboard dongle to be plugged into the Beckhoff PLC inside the cabinet. Input and output activation when testing the sole module is done through the Twincat project rather than through WinMulti The above is only required If the Machine is not fully installed and connected with power air and network already. The below guide is specifically for a fully installed and connected infeed.ically for a fully installed and connected infeed.)
ZX5 Alignment Check + (The ZX5 machine can be tricky to align as there are many adjustments designed into the table to offset manufacturing tolerances. This step by step guide follows the correct protocol to ensure the starting point and sequence of alignment is correct)
R0000299 Stroke assembly rebuild Part 2 + (The following instructions should be follo … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
ZX5 Gripper Energy Chain & Tray Setup + (<div class="icon-instructions caution-i …

...August 2023 - The energy chain and method used in this dokit has been superseded by https://stuga.dokit.app/wiki/Energy_Chain_Installation_-_2500_Series

The main problems we’ve had during commissioning with these energy chains is that if they are not positioned well enough , the chain will clip the button heads that hold the trays to the L brackets To get over this the brackets sometimes need adjusting on the slots along with possibly bending into a better shape or by adjusting the chain bracket position on the slots in the ‘finger’ bracket Things to look out for: *There should be three links which are reversed at the bracket end of the energy chain. *Servo cable and the pipes and cables from the energy chain are fixed with cable ties to the fingers on the bracket to minimise possible movement and twisting which changes where the energy chain sits in the trays, meaning it could start clipping the button heads. *Tray heights and energy chain length, there should be a consistent gap all the way along between the energy chain and the top tray (viewed from inside the tray) and when at the full travel either end the chain shouldn’t be tight hitting the fence too much at the end. *It is also worth checking if all of the links fitted are the same radius type, as we have had occasions where some have been a smaller radius meaning at certain points down the rack the radius of the bend becomes smaller and falls out from the support of the top tray, especially when the gripper is at either end of the rack. There is a code on the side of each link in the energy chain. *A last thing to be weary of is is the end corners of the trays may require bending out, there have been occasions where one chain tray has been slightly more bent in than the other meaning when the chain moves from one tray to the next it clips the corner of the next tray We normally get the gripper on a reversing cycle movement to test this through the twincat project at different speeds, starting slow and working up to higher speeds.gh the twincat project at different speeds, starting slow and working up to higher speeds.)
Upgrade - R0000173 Conveyor Motor + (The original style of conveyor is used on many machines, but the motor that powers it is no longer available. This guide will allow a different motor/gearbox to be used.)
Stuertz Infeed - Align and dowel GX rack +
Hikvision Camera Setup + (These are the Hikvision DS-2CD2343G0-I Cameras (C0001152) that will replace the obsolete UCAMs that have been used on previous machines. Connected via a multi way PoE injector (C0001238). And with SD card (C0001239).)
Alignment guide using wire line + (This dokit is to help with the use of a wi … This dokit is to help with the use of a wire line to set alignment correctly on mechanical build up. Using a wire line correctly will ensure a very accurate straight line is achieved . Accuracy of + - 1 mm over any distance can be achieved using the following method. Using one incorrectly can also easily be done.! The steps shown can be applied to all types of alignment , when you have a vertical face on components that require aligning. face on components that require aligning.)
Allocations + issuing received parts + (This involves splitting down received orde … This involves splitting down received orders into the JC/Pick bins the parts have been allocated to by Sage. If there are parts to be allocated, after filling in the 'this delivery' column and pressing save, if there are parts to be allocated a list will appear. this list is in order of part number and in the sub-screen after highlighting each part number the specific Job card numbers will show quantities required for each bin and also the quantity to be allocated from the order received.y to be allocated from the order received.)
Flowline 6 to 6o5m Extension + (This procedure describes how to upgrade a … This procedure describes how to upgrade a flowline to increase the standard capacity from 6.0m to 6.5m. The procedure involves extending the machining centre outfeed travel and saw infeed travel base to 6.0m to cope with a longer rail on each side. These are generally supplied as a new part. Other ancillary parts that will need extending * Cables * Energy Chainsl need extending * Cables * Energy Chains)
Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
ZX5 Transfer Table Crank set up + (This tutorial will show you how to mechani … This tutorial will show you how to mechanically set up the cranks and sensors so that the correct overlaps between the different cranks are achieved. Crank C is the crank on the Machining Centre Outfeed that controls the single pop up. Crank D is also mounted on the Machining Centre Outfeed and controls the pop ups on the Transfer Table. Crank E is the crank on the Saw Infeed and controls the single pop up that moves the profile in to the channel. that moves the profile in to the channel.)
R0019207 Upgrade SR Axis Spigot + (This upgrade utilises upgraded parts to en … This upgrade utilises upgraded parts to ensure a mechanical fix is maintained between the SR axis gearbox and main drive pin , whilst also giving the ability once upgraded for the gearbox to be removed with minimal mechanical time. three main parts will be replaced in this upgrade, obsoleting the removed parts Main components of upgrade D00004019E Turntable Mk5 D0004033E Alignment disc Mk5 D0004147E Turntable shaft Mk5nt disc Mk5 D0004147E Turntable shaft Mk5)
B0000082b Motor replacement For Obsolete part B0000082 + (To rectify the obsoletion of B0000082 driv … To rectify the obsoletion of B0000082 drive motor, the following replacement kit has been designed to enable continued support of older assemblies within stuga machines . The kit consists of a new motor and appropriate gearbox, adapter plate and new fasteners . Also details are included here for a small modification to enable the upgrade to function correctly Following parts are required for this upgrade B0000082b load motor and gearbox 1 off D0008225b adapter plate F0000189 M6 x 25 set bolts 4 off F0000058 A form washer 4 off F0000190 M8 x 40 set bolts 2 off F0000007 M5 x 16 cap head bolt 4 off off F0000007 M5 x 16 cap head bolt 4 off)
R0010309 Ecoline Ultrasonic Material Loaded Upgrade + (Upgrade of load sensor For infeed table on … Upgrade of load sensor For infeed table on Ecoline machines '''Component list''' A0001046 P Clip 6mm Steel / Rubber Liner x 2 D0010973 Material Loaded Sensor Plate x 1 E0001104 PreMade Cable: M8 Socket 4 Way Cable 5m x 1 E0001120 Sensor: Ultrasonic M8 20-150mm x 1 M0001053 Copper Tube 6mm x 4.4mm 10m Coil x 0.3 P0000046 Fitting: 'Y' Adaptor 6mm x 1 P0000069 Tube to tube fitting 6mm x 1 P0000160 Fitting: Flow Controller In Line 6mm x 1
000160 Fitting: Flow Controller In Line 6mm x 1 )
Upgrade Autoflow to Windows 10 + (Update 2024 - Upgrades now consist of a ne … Update 2024 - Upgrades now consist of a new Windows 11 PC with VM for the front end and a C6017 PC for the back end. Upgrading an Autoflow to Windows 10 involves upgrading two PCS #The Beckhoff control PC - replaced with a C0001225-KIT #The Camera PC - replaced with a C0000422-KIT with a VM setup. this now becomes the front end PC
=== For Historical reference, these are the pre-2024 notes: === ''Upgrading an Autoflow to Windows 10 on site involves upgrading two PCS'' #''The Beckhoff control PC'' #''The Camera PC'' ''
The Beckhoff PC is not upgradable so needs to be completely replaced. We use the miniature [https://www.beckhoff.com/english.asp?industrial_pc/c6017.htm Beckhoff C6017] for this'' ''It is not cost effective to upgrade and old camera PC, so a new one is supplied'' ===''Notes''=== *''The Beckhoff PC is now powerful enough to run the front end and back end.'' *''The camera PC is there to replace the camera PC on site and contains the storage for the machine cameras'' *''Because the Beckhoff PC has limited hard drive space, the DDRIVE will be on the cameraPC''hard drive space, the DDRIVE will be on the cameraPC'')
R0015079 Infeed extension assembly + (instructions and parts required for fittin … instructions and parts required for fitting of frame extension Parts required Levelled infeed frame D0015475 Infeed frame Extension leg 1 off D0015476 Infeed frame Beam upper 1 off D0015477 Infeed Extension Beam Lower 2 off F0000266 M16 set bolt x 2 F0000234 M16 nut x 2266 M16 set bolt x 2 F0000234 M16 nut x 2)
R0000299 Stroke assembly rebuild + ( The following instructions should be fol … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)