Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

GE Control Components Changeover + (A step by step process of how to change all of the GE electrical components over to the new Eaton variants. This Dokit will also be a log to keep hold of historic changeovers with the electrical components.)

GE Control Components Changeover +
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Alignment process and criteria for module B to C)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Alignment process and criteria for module A aligning to module B)
R0015114 Bench Assemble Valve Banks and Regulators + (Assembly details for pneumatic components)
R0015298 Bench Assemble V notch Clamps + (Assembly instructions for Clamp components)
Beginners Guide to uPVC Manufacturing Process + (Basic Introduction to uPVC Manufacturing process)
R0000572 Bench Assemble Centralise Assembly + (Bench assembly details for centralise components)
R0000570B Bench Assemble 1st stage Ejector + (Bench assembly details for ejector components)
R0015254 Bench Assemble shafts, Bearings and Pinions + (Bench assembly instructions for drive components)
R0000963E Bench Assemble Z axis Components + (Bench assembly instructions for z axis components)
Monday - Putting Customer Machines On Stop + (Correct process for placing a customer on /off stop)
Setting Up C0000422-KIT - Full Hardware 2023 + (Creating the C0000422-KIT from the hardware components ready for stores)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Details for correct alignment and process steps)
R0015323 Mount Electrical Cabinet + (Details for final mounting of electrical cabinet)
R0015335 Mount Electrical Cabinet + (Details for mounting of electrical control panel)
Stuga Flowline Overhaul Particulars + (Details of the components replaced on a Flowline Overhaul)
R0015146 Pneumatic pipe Installation Part 2 + (Details to install pneumatic and electrical loom)
R0015146 Pneumatic pipe Installation Part 3 + (Details to install pneumatic and electrical loom)
R0015146 Pneumatic pipe Installation + (Details to install pneumatic and electrical loom)
Dokit - Editing Work Instructions + (Editing the content n a Dokit Work Instruction)
TB0238 Fault Finding 300Hz Spindles + (Faults on the 300Hz spindle circuit have p … Faults on the 300Hz spindle circuit have proved to be very difficult to trace. There symptoms are quite straight forward, but failing to find the real root cause has created huge costs in revisits and destroyed components. It is vital that all root causes are examined and eliminated, as there is often more than one root cause and very often they are intermittent.ause and very often they are intermittent.)
R0015303 Fit backplates and covers + (Fitting of final parts to rotary ring after electrical installation and function testing)
Troubleshoot - Permanent IP Address - Windows 10 + (How to change or create a permanent IP address on a Windows 10 PC.)
Troubleshoot - Permanent IP Address - Windows 8 + (How to change or create a permanent IP address on a Windows 8 machine.)
Troubleshoot - Permanent IP Addresses - UVision Cameras + (How to change the IP address on the obsolete UVision camera systems.)
ZX5 Adjusting V Notch Depth and Position + (How to change the depth and position of the V notch on a ZX5 machine)
Changing Main Saw Blade + (How to change the main saw blade on a Stuga machine)
Changing Version Control to Visual Studio + (How to change the version control software from Sourcetree to the inherent system on Visual Studio)
Dokit - Creating A Work Instruction + (How to create aInstruction in Dokit)
Setting Fast Registration Scanning on ZX5 + (How to set the electrical and software settings to allow fast registration scanning on a ZX5 to detect motor slippage issues)
WEG Inverter Setup + (How to set up the WEG inverters. used on the Transfer crank and Infeed modules. These are fitted to some ZX5 machines in the field replacing the Eaton Inverters for a short period.)
Troubleshoot - Permanent IP Address - Windows 7 Embedded - Beckhoff + (How to setup or change the IP address on a Beckhoff CX5120/CX5020 running on Windows 7 Embedded.)
Turning Off and Changing Datum Tool + (How to turn off a spindle and change the datum tool.)
R0015034B ZX5 Module B Wiring Loom installation Part 3 + (Installation steps for Electrical looms installation into Module B)
R0015034B ZX5 Module B Wiring Loom installation + (Installation steps for Electrical looms installation into Module B)
R0015034B ZX5 Module B Wiring Loom installation Part 2 + (Installation steps for Electrical looms installation into Module B)
R0000962E Bench assemble Y axis Components + (Instructions for assembling components)
R0015080 Bench Assemble Sensor Rail + (Instructions for bench assembly of sensor rail components)
R0015035 Bench Assemble V Notch Components + (Instructions for bench assembly of v notch components)
Changing saw pusher bearings - Standalone Saw + (Instructions on how to change Saw pusher bearings on a standalone saw infeed.)
Changing Pneumax Valve slice + (Instructions on how to change a Pneumax valve slice)
R0015356 Assemble Pneumatics on to electrical cabinet + (Instructions to mount pneumatic components)
Fitting R0019199 Upgrade: Autoflow Slewing Ring Guard Kit + (Kit R0019199 contains a kit of components for protecting the SR axis bearing system on an Autoflow. This area is prone to collect offcuts which can pull the seal from the SR axis bearing)
Install markings and measurements ZX5 + (Markings and measurements required by the … Markings and measurements required by the Install team, after a machine commission. This helps towards a smoother install process, getting the machine module positions and fencing to be in the same place (or close to) as they were during the commission at stuga base. were during the commission at stuga base.)
Monday - Getting Started For Engineers + (Monday is a task management system that ca … Monday is a task management system that can be configured for anything. It can be used for to-do lists and project planning or that needs to hold a To-Do list of tasks. It allows a history of actions for tasks, along with an upload area for any type of file, photo, etc. Its real strength is in team communication, as everyone has access to all the informationeveryone has access to all the information)
Naming Conventions for Electrical Components + (Policy for naming Electrical Components)
R0015078B Module A infeed arm alignment + (Process for alignment of infeed arms)
Saje uPVC Unloading Process + (Process for unloading and locating Autoflow Mk4 machine in Saje upvc)
Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3 + (Process for upgrading an Autoflow from the original TwinCAT2 system to a new PC with Windows 10 and TwinCAT3)
Programming Eaton DE Drive + (Programming the Eaton DE Drive)
Changing Office 365 Password + (Short guide on how to change your office 365 password)
Stuertz VSM 30.20-P Welder Installation + (Step by step guide for installing Sturtz Welder)
Throwaway Chutewidth and SmallestGrip + (The parameters work together to define the … The parameters work together to define the process that happens with the final offcut at the end of a bar when it is too small to be ejected onto the outfeed table. It is surprisingly complicated, particularly on an Autoflow machine where the final piece is gripped. machine where the final piece is gripped.)
TB0434 Setting Up Deep Y notches on ZX5 + (The saw “Y drive” on a ZX5 is limited in i … The saw “Y drive” on a ZX5 is limited in its depth range to +/- 20mm from the centreline of the profile, and 20mm from the backfence. This is fine for most normal Y notching, but there are combinations when a particularly deep Y notch is required. This process is also useful on an Autoflow where the SY axis distance is limited by the backfence / top clamp interference by the backfence / top clamp interference)
Fitting M8 Plug for EtherCAT Boxes + (This Dokit sets out be a guide on fitting m8 field attachable plugs to cable assemblies.)
Filling Out An Online Daily Timesheet Form + (This Dokit will give a step by step guide on how to use the Monday.com form to fill out a daily timesheet.)
Guide to Fitting Eject Push Sensors on ZX Machines + (This Dokit will provide step by step instructions on how to retrofit home and out sensors to the eject push bar on ZX machines.)
TB0408 Stuga PCB Design Normalisation + (This document records the result of the process carried out today to “normalise” the design and part notation for the PCBs that Stuga outsource. This follows confusion of poor naming and a lack of part numbers.)
R0000164 Spindle Disassemble for Required parts + (This dokit details the method of disassembly and list of parts that can be salvaged from a faulty R0000164 spindle assembly)
Installation Guide - ZX5 Electrical + (This guide is to be used for all of the electrical connections when installing a ZX5 machine.)
Setting Up New Printer - GX420d + (This guide will take you through installing a new printer (GX420d) step-by-step:)
Autocut Adding New Profile + (This is a step-by-step instruction manual for adding new profiles on an Autocut Saw)
Removing or changing a Beckhoff AX8000 series servo drive + (This is the process of removing or changin … This is the process of removing or changing a Beckhoff AX8000 series servo drive. Unlike the AX5000 series, these drives are all supplied by one power unit containing the 3-phase and 24v connections (underneath) as well as the EtherCAT connections (on the front). All the drives in the unit are then connected together by design.nit are then connected together by design.)
ZX5 - Specialised Settings for Eaton DE Drives + (This page lays out the settings needed for each individual Eaton drive on a ZX5 or Autoflow Mk4. It is important to use these settings to stop slim profiles toppling over on the transfer table)
Changing the Flowline Ops Password + (This tutorial will instruct the operator in the correct procedure to change the password in Flowline Ops)
Upgrade ZX Machine to Beckhoff Drives and Control + (This tutorial will provide a step by step guide on how to upgrade a ZX style machine to have Beckhoff drives and control system.)
TB0371 Setup of Beckoff EP7041 Stepper Controller + (Tuning of EP7041 box is tricky, but following a step through telephone call with Etienne at Beckhoff, it was successful with the following steps)
ACEpc Changing IP address using netedit + (Using the netedit program to change the IP address of an ACEpc running DOS software)
Refurb Saw Cabinet Valuable Parts + (Which Electrical parts to keep from a saw cabinet)
Pneumax Valve Bank Recycling + (Which components to send back to Stuga for recycling)
R0015286 Bench Assemble X axis Components and Energy Chain + (instructions for bench assembling x axis components)