Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

• TB0407 Replacing Infeed Belt with Joined Belt  + (The infeed belts on Flowlines and Ecolines require the disassembly of the infeed tables to replace the belts. Jointed belts will now be supplied when replacement required. These belts are cut and use threaded pins to join the ends into a continuous belt.)

• TB0450 CMOS Battery Replacement  + (0450 CMOS Battery Replacement)
• Stuertz Infeed - Align and dowel GX rack  + (Align and pin main rack on Stuertz infeed)
• R0000571 Fit and Level Cut Tables , Finalise Eject  + (Alignment and fitment details for cut tables and eject drive)
• R0015079 Infeed extension assembly  + (Assembly instructions for infeed module A extension section)
• ZX4 Infeed Module  + (Brief explanation of the mechanics and operation of the ZX4 infeed table.)
• Setting Infeed Datum Clamp  + (Correct Setup of the Infeed Datum Clamp)
• Stuertz Infeed Table Measurements  + (Critical measurements and settings for an Autoflow infeed table)
• TB0394 Fitting Ultrasonic Sensor to Flowline OCLEAR  + (Currently, the Flowlines have an m12 barre … Currently, the Flowlines have an m12 barrel sensor fitted for the OCLEAR sensor. After research and updates to new machines, we have found that fitting an ultrasonic sensor is much more reliable and effective at picking up different profile colours. For this reason, we have created an upgrade kit to enhance the functionality of the OCLEAR sensor.ce the functionality of the OCLEAR sensor.)
• R0015402 Cover Guard For Infeed Motor  + (Fitting infeed motor cover plate)
• D0016453 Infeed Motor Cover  + (Fitting the D0016453 Infeed Motor Cover)
• Fitting ZX5 Saw Infeed Guide  + (Fitting the infeed guide for the ZX5 saw)
• TB0287 Importance of Outfeed Clear Sensor  + (Following an H&S Incident (0005 – Nova … Following an H&S Incident (0005 – Nova Profile Ejecting), all flowlines and ZXs need to be checked to ensure the “Outfeed Clear” sensor is working. The incident proved that if the sensor fails, the outfeed may not be clear and hence the profile can be pushed back through the machine.rofile can be pushed back through the machine.)
• Reducing Saw Cut Height for Lower Profiles  + (For sawing modules running from winMulti ( … For sawing modules running from winMulti (including flowlines with integrated control), there is an option to reduce the cut height. This is managed through an additional sensor on the saw cut stroke cylinder. This is particularly useful on saws with a 500mm blade (to cut wide or tall profiles) but a reduced cycle time can be gained by reducing the saw cut stoke time by limiting its travel on shorter profilesby limiting its travel on shorter profiles)
• ZX5 MH Infeed Basic IO Test and Setup  + (Guide for basic Input and Output testing / setup on the ZX5 MH Infeed Module)
• B0000025 B0001175 Belt Identification  + (Guide to correct identification of appropriate Saw blade motor drive belts)
• Stuertz Infeed - Check GY Position Parallelism  + (How to check the parallelism of the Stuertz Infeed - GY axis position to backfence)
• C0001005MM Micromech Stepper Motor Assembly  + (How to convert a C0001292 Motor into a replacement for a Beckhoff C0001005 replacement)
• Stuertz Infeed Mk4p1- Setting GY and GZ Datum  + (How to correctly configure the datum points on the Stuertz Mk4.1 Infeed)
• Setting Infeed Loading Wheel  + (How to correctly set the pressure and clutch settings on the infeed loading wheel)
• Fitting Yaskawa Inverter  + (How to fit a Yaskawa Inverter as a replacement in the field)
• Replacing Beckhoff PC  + (How to replace a beckhoff PC and install the original project)
• Replacing Baldor Microflex Drive with RS Automation  + (How to replace an existing Baldor Microflex drive with RS Automation CSD7)
• TB0431 Samsung Drive Parameter Setup  + (How to set up a new or replacement Samsung drive using the jogger.)
• WEG Inverter Setup  + (How to set up the WEG inverters. used on the Transfer crank and Infeed modules.)
• TB0189 Narrow Profile Next to Wide on Infeed Table  + (If a very narrow section is followed by a very wide section on the Autoflow infeed, there is a collision point resulting in damage to the infeed measuring sensors.)
• R0019264 Autoflow Mk 4,1 Infeed Table Safe moving equipment guide  + (Information for use of R0019264 kit for safe moving of Autoflow Mk4.1 Infeed Table)
• R0015090 Bench Assemble Roller Tables  + (Instructions for bench assembling Roller tables)
• R0015121 Bench assemble Infeed arms  + (Instructions for bench assembling infeed arms)
• Changing saw pusher bearings - Standalone Saw  + (Instructions on how to change Saw pusher bearings on a standalone saw infeed.)
• Stuertz Infeed - Reinforcing Forward Clamp Energy Chain System  + (Instructions on reinforcing the energy chain on Stuertz infeed table forward clamp system)
• R0015046 Bench Assemble Infeed Clamps  + (Instructions to bench assemble infeed clamp assembly)
• R0015095 Bench Assemble Infeed Support Arms  + (Instructions to bench assemble infeed support arms)
• R0015063 Bench Assemble Roller Tables  + (Instructions to bench assemble roller tables)
• Item:R0019014  + (Kit for replacing Flowline Opto infeed sensors with ultrasonic)
• Install markings and measurements ZX5  + (Markings and measurements required by the … Markings and measurements required by the Install team, after a machine commission. This helps towards a smoother install process, getting the machine module positions and fencing to be in the same place (or close to) as they were during the commission at stuga base. were during the commission at stuga base.)
• R0019264 Autoflow Mk 4,1 Infeed Safe moving equipment  + (Moving equipment for Infeed Frame of Autoflow Mk4.1)
• Outfeed Support Roller - Flowline  + (Part code R0010276 - Extra support roller upgrade added to replace single roller on outfeed rear clamp.)
• R0015078B Module A infeed arm alignment  + (Process for alignment of infeed arms)
• Relay Replacement  + (Relay Replacement guide)
• RMZX511 Conveyor Pinch Point  + (Removal of the pinch point created between the conveyor belt and the extractor swarf hood)
• Sales Document - Main Linear Rails  + (Replacement linear rail option details)
• B0000370 Slideway Bearing Compatibility  + (Replacement of B0000370 bearings)
• CX5120 Replacement  + (Replacement of a CX5120 on a customers machine.)
• Commissioning - Off-Cut Laser Sensor  + (Setting up the laser sensors on the infeed of a Flowline, ZX4 and ZX5.)
• TB165 C0001 Stepper Motor Obsolescence  + (The C0001 stepper motor used on the G axis of flowlines and on all motors on the router has become obsolete. A replacement will be available using the same Stuga part number)
• ZX4 Infeed Roller Reinforcement  + (The design of the ZX4 Infeed Table was suc … The design of the ZX4 Infeed Table was such that the first roller was located by a single block, of which was attached to the first arm by 2 bolts and a single dowel. The clearance on the two bolt holes meant that the block could rotate slightly around the dowel, resulting in the roller having a large potential deflection when load was put on it.ential deflection when load was put on it.)
• TB0407 Replacing Infeed Belt with Joined Belt  +
• TB0420 Obsolescence Note - Flowline Spindle Motors  + (The original motor is no longer available, and a replacement has proved impossible to find due to the physical size of the motor)
• TB0161 Fitting Outfeed Clear Sensor on ZX Machine  + (The outfeed clear sensor that existed on Mk3 flowlines was not repeated on ZX machines. This leaves the machine vulnerable to crash.)
• TB0434 Setting Up Deep Y notches on ZX5  + (The saw “Y drive” on a ZX5 is limited in i … The saw “Y drive” on a ZX5 is limited in its depth range to +/- 20mm from the centreline of the profile, and 20mm from the backfence. This is fine for most normal Y notching, but there are combinations when a particularly deep Y notch is required. This process is also useful on an Autoflow where the SY axis distance is limited by the backfence / top clamp interference by the backfence / top clamp interference)
• ZX5 Gripper Energy Chain & Tray Setup  + (Things to look out for and check when setting up ZX5 energy chains on the ZX5 MH Outfeed or Saw Infeed)
• ZX5 Improvements and Upgrades  + (This document is intended for existing users and owners of Stuga Flowlines to help explain the improvements and enhancements made to the flowline / ZX3 / ZX4 range of machines into out latest flagship product - the ZX5)
• TB0452 ZD620 Zebra Printer Setup  + (This document outlines the setup of the new ZD620 printers to replace the older Zebra 420d printers that are obsolete. Also Applies to ZD420 and ZD421 printers)
• R0000164 Spindle Disassemble for Required parts  + (This dokit details the method of disassembly and list of parts that can be salvaged from a faulty R0000164 spindle assembly)
• Maintenance - Tensioning for R Axis on ZX3  + (This guide explains how to accurately tension the R Axis belt on the ZX3)
• Removing or changing a Beckhoff AX8000 series servo drive  + (This is the process of removing or changin … This is the process of removing or changing a Beckhoff AX8000 series servo drive. Unlike the AX5000 series, these drives are all supplied by one power unit containing the 3-phase and 24v connections (underneath) as well as the EtherCAT connections (on the front). All the drives in the unit are then connected together by design.nit are then connected together by design.)
• Safety Circuit Principles  + (This page will give you the required infor … This page will give you the required information and understanding of the principles of a safety circuit and generic idea on how to identify faults. For the safety ciruit master document, use this link: https://stuga.dokit.app/wiki/Fault_Finding_-_Safety_Circuits_Masteriki/Fault_Finding_-_Safety_Circuits_Master)
• Easily resizable forms for any screen resolution in Visual Studio  + (This tutorial takes the developer through a way to create resizable forms in Visual Studio with NO CODING Required.)
• Setting up an Ecoline Barcode Scanner  + (This tutorial will teach you how to correctly set up an Ecoline Barcode Scanner. This could either be a handheld device or an 'Orbital' scanner attached to the infeed table.)
• TB0426 Replacement Zebra Printer Setup  + (This will describe the setup of a replacement Zebra printer after a fault with one on site.)
• ZX5 Datum and Grip Pin Setup  + (This will guide you through the machanical setup of the grip pins, along with datum and loadPos calibration.)
• B0000082b Motor replacement For Obsolete part B0000082  + (Upgrade parts and procedure to replace obsolete load roller motor B0000082)
• Upgrade Flowline Opto Sensors to Ultrasonic  + (Upgrading the 3 off opto sensors on a flowline Mk3 infeed table to ultrasonic version)
• Autoflow Maintenance - Infeed  + (Weekly and Monthly Maintenance Procedures for Autoflow Infeed Table)
• ZX5 Clamp and Gripper Height Changes for Tall Profile  + (With the correct model and spec the ZX5 is … With the correct model and spec the ZX5 is able to take some tall profiles above 90-95 mm tall. To be able to take any profile bar above 90mm in height, certain manual mechanical changes and adjustments are required to the saw outfeed clamp and the grippers, by the operator / maintenance engineer, before being able to put a tall profile through the machine. The below guide shows how to carry out these adjustments. shows how to carry out these adjustments.)
• TB0445 ZX5 Setup - Infeed Measure Sensor Calibration  + (ZX5 Setup - Infeed Measure Sensor Calibration)