Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

Saw machining centre alignment and level check points + (Bullet pointed checks to determine correct alignment of key components within Sawing unit)

R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (<nowiki>'''Tools required&l … '''Tools required'''

Tape rule

Steel rule

standard hex keys

Standard HSS drill set

Standard Tap set

Hack saw

Ball Pein hammer

Centre punch

'''Part Required'''

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 3

P0000024 Fitting: Hex Nipple 1/4 BSP x 1

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000097 Fitting: Elbow Adaptor 8mm - 1/4 BSPT x 1

P0000159 Fitting: Stem Blanking Plug 6mm x 3

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000279 Female Cross 1/4'' NPT x 1

P0000297 HighLow Pressure Valve x 1

P0000419 Air Service Unit OH (P0283)x 1

P0001070 Valve Base: Type 41 6 Position Ø6 x 2

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8

P0001101 Male straight 12mm to 1/4 bsp x 5

P0001102 Male elbow 12mm to 1/4 x 2

P0001186 Valve 24v dc SMC x 12

;P0001070 Valve Base: Type 41 6 Position Ø6 x 2 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8 P0001101 Male straight 12mm to 1/4 bsp x 5 P0001102 Male elbow 12mm to 1/4 x 2 P0001186 Valve 24v dc SMC x 12 </nowiki>)
R0015114 Bench Assemble Valve Banks and Regulators + (<nowiki>'''Tools Required&l … '''Tools Required'''

Standard hex key set

Standard spanner set

Standard HSS drill set

Standard tap set

'''Parts Required'''

H0007998 Regulator internal mount 5 way x 1

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14

P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9

P0000021 air gun assembly x 1

P0000024 hex nipple 1/4 x 3

P0000058 Regulator Mounting Kit x 1

P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2

P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2

P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2

P0000145 tee equal 1/4 x 3

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1

P0000278 Regulator 0-2 bar x 1

P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8

P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1

P0000419 Air Service Unit OH (P0283) x 1

P0001071 Valve base type41 8 position x 1

P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4

P0001101 Male straight 1/4 bsp to 12mm x 2

P0001102 Fitting male elbow 12mm 1/4 x 4

P0001105 Bulkhead straight 12mm x 6

P0001186 Valve. 24v dc smc x 8

 P0001071 Valve base type41 8 position x 1 P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4 P0001101 Male straight 1/4 bsp to 12mm x 2 P0001102 Fitting male elbow 12mm 1/4 x 4 P0001105 Bulkhead straight 12mm x 6 P0001186 Valve. 24v dc smc x 8 </nowiki>)
R0015347 Bench Assemble Duplex extraction unit + (<nowiki>'''Tools Required'' … '''Tools Required'''

Standard Spanner set

Lifting platform

standard screwdriver set

'''Parts Required'''

M0000151 Extractor Poly Bags 700G 31.5'' Layflat 50'' Long x 2

M0000274 Extraction Unit Duplex 2off 8' Bags (No Starter) 1850mm x 1

M0000036 ear defence sticker x 1

t;br /> M0000274 Extraction Unit Duplex 2off 8' Bags (No Starter) 1850mm x 1 M0000036 ear defence sticker x 1 </nowiki>)
R0000558E Bench Assemble Base and Turntable + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1
ainless lock washer x 4 D0015663 SR Axis Motor Guard x 1 )
R0015093 Bench Assemble Transfer Beam + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard hand taps V rail alignment Jigs Drill driver and 4mm hex fitting '''Parts Required''' B0001155 OpenRail 1000mm Long x 32 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9
2 B0001170 spacer x 320 D0015571 Transfer Arm (2018) x 9 )
R0015278 Mount Completed Assemblies Section two + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 2 D0015718B Energy Chain Angle Bracket Double Deck x 3 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 2 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 D0015862 Energy Chain Tray Deep Long x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chainsembly R0015286 Bench Assemble X axis components and energy chain)
R0015314 Fit Z Axis Drive components + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Engineers level 300mm 5mm Carbide drill 150m verniers '''Parts Required''' A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2 A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2 B0000344 Circlip 15mm External x 2 B0000400 Circlip 17mm External x 2 D0001249 Z Axis Chain Offset Plate x 1 D0001271 Z Axis Chain Mounting Plate x 1 D0001927 Intermediate Housing (AM3032) x 1 D0006498 Z Housing Cap x 2 D0007453 Double Cylinder Bracket OH (D8106) x 1 D0007610 Chain Slide x 1 D0007795 Nut Housing x 1 D0007796 Nut Housing - Mirror x 1 D0007858 Kit: Z Axis Drive Chain ZX + Micro x 1 D0008106 Double Cylinder Bracket (D7453) x 1 H0007714 Z Spocket 20 teeth x 2 R0000963E Bench Assemble Z axis Components x 1
teeth x 2 R0000963E Bench Assemble Z axis Components x 1 )
R0015278 Mount Completed Assemblies + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0008288 Takeup Pad Left (D7339) (Wet/P F Matt) x 1 D0015583 Take Up Beam Joiner x 1 D0015598 Datum Flag: Saw Infeed x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 1 D0015723 Energy Chain Tray Shallow x 1 D0015724 Energy Chain Tray Deep x 1 D0015725 Energy Chain Tray Shallow Medium x 1 D0015742 Takeup Pad Right ZX5 x 1 E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 1 R0015011 Bench Assemble Gripper R0015063 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015101 Bench assembly take up assembly R0015286 Bench Assemble X axis components and energy chain
R0015286 Bench Assemble X axis components and energy chain )
R0015100 Fit Guarding + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set '''Parts Required''' D0001878 Rear Door Saw Mk4 (1879) x 1 D0004584 Outfeed Side Rest x 3 D0015703 Air Gun Bracket x 1 D0016203 Compliance Guard - Saw Lower Front x 1 D0016204 Compliance Guard - Saw Lower Side x 1 D0016265 Saw Front Door: Bernstein Mount Plate x 1 D0016266 Saw Front Door: Bernstein Guard x 1 E0001569 Guard Lock Switch: Bernstein Radius Actuator (Key) x 1 M0000055 Saw Blade Spanner (24mm Combination) x 1 M0001051 Bullet Catch 70 x 12 x 1 P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 6 P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x 3 P0001009 Panel Mount Nut (To suit P0001008) x 3 R0015041 Bench Assemble Top Hood Assembly x 1 R0015337 Bench assemble guarding components x 1 R0015338 Bench assemble serial plate x 1
g components x 1 R0015338 Bench assemble serial plate x 1 )
R0000558E Bench Assemble Base and Turntable Part 2 + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard spanner set Heat gun Large Internal Circlip pliers Standard circlip pliers 8mm hand reamer Grease gun Torque wrench '''Parts Required''' B0000028 Thrust Bearing 140 I/D 180 O/D 31 Long (FAG) x 1 B0000032 Linear Bearing: Ø30 x 50 Compact (Metal Case Only) x 4 B0001087 Angular Contact Bearing 70 I/D 125 O/D 24 Long x 1 B0001088 Circlip 125mm Internal x 1 C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1 C0001179-100 Gearbox NPTO 100-1 x 1 D0004019E Turntable Mk5 (5334E) x 1 D0004033E Alignment Disc Mk5 x 1 D0004147E Turntable Shaft Mk5 x 1 D0004320E Thrust Bearing Housing Mk5 x 1 D0004336 Stay Bar x 2 D0004514E Turntable Base Mk5 x 1 D0004516 Front Bearing Block (5294) x 2 D0010778 Turntable Stop Arm x 1 D0010796 Turntable Housing Cover x 1 H0004631 Shaft 30mm: Base Slide x 2 M0001176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1176 M6 Stainless lock washer x 4 D0015663 SR Axis Motor Guard x 1)
R0015350 Fit Rigid Ducting + ('''Tools Required''' … '''Tools Required''' Duct tape '''Parts Required''' M0000116 Ø200mm to 3 way (Ø125mm) extractor pipe connector x 1 M0000118 Ø200mm - 90 deg Bend Ducting x 1 M0000185 Ø125 mm ID 45 degree bend x 1 M0001045 Rigid Ducting Ø125 x 1000mm x 2 M0001213 Rigid Ducting Ø200mm x 500mm x 2 M0001214 Rigid Ducting Ø200 x 2000mm long x 3 M0001228 Extraction Unit inlet taper x 3
mm long x 3 M0001228 Extraction Unit inlet taper x 3 )
R0015255 Mount Assemblies to Main Frame + ('''Tools Required''' … '''Tools Required''' Standard Hex key set Standard spanner set 300 mm rule 1000mm rule '''Parts Required''' D0015291 Datum Flag x 1 D0015717 Energy Chain Angle Bracket Lower x 5 D0015718 Energy Chain Angle Bracket Upper x 5 D0015720 Carriage Bracket x 1 D0015721 Energy Chain Tray Deep Long x 2 D0015722 Energy Chain Tray Shallow Long x 1 D0015861 Energy Chain Cable Support x 1 R0015007 Bench Assemble Roller Tables R0015096 Bench Assemble Transfer Drive Assembly R0015251 Bench Assemble X axis components and energy chain R0015004 Bench Assemble Gripperaxis components and energy chain R0015004 Bench Assemble Gripper)
Laser Setup on Flowline/ZX3 for Laser Holes + ('''How to Setup .''' This will Cover the … '''How to Setup .''' This will Cover the Basic Alignment of the receiver and Sender setup. Focusing the Laser and Setting up the Receiver Sensitivity. Always Make sure Laser Sender and Receiver are clean and both lenses have been wiped with a soft cloth first.
en wiped with a soft cloth first. )
R0015338 Bench Assemble Serial Plate + ('''Tools Required''' Serial plate stamping jig Large Alphabetic and Numerical stamps Correct machine build data '''Parts Required''' D0000086B Universal Serial Number Plate (UKCA) x 1 )
R0015315 Fit Y Axis Drive components + ('''Tools Required''' … '''Tools Required''' Standard hex key set External circlip pliers '''Parts Required''' B0000344 Circlip 15mm External x 1 D0001927 Intermediate Housing (AM3032) x 1 D0006487 Y Stepper Housing x 1 R0000962E Bench assemble Y axis Components
per Housing x 1 R0000962E Bench assemble Y axis Components )
R0015310 Install V Notch Subframe + ('''Tools Required''' … '''Tools Required''' Standard hex key set Standard Spanner set Parallel setting blocks 600mm rule 1 meter straight edge 2 meter straight edge 12 " engineers level 12" engineers square '''Parts Required''' D0015151 Shaft End Washer x 8 D0015155 Vertical Spacer Bar x 4 D0015150 shaft 40mm zx v notch x 4 D0015169B cylinder rod bracket x 2 R0015035 Bench Assemble V Notch Componentsinder rod bracket x 2 R0015035 Bench Assemble V Notch Components)
TB0428 Connecting To Yaskawa with Silex USB + (== What is the Silex DS-510? == The Silex … == What is the Silex DS-510? == The Silex unit is a USB server, allowing a PC to have a USB port anywhere over an ethernet network. This is useful to connect the PC to a Yaskawa inverter when they are located in different cabinets. The software sets up a virtual USB port which can then be used to run the Yaskawa DriveWorks software.ed to run the Yaskawa DriveWorks software.)
Correcting Linearity with Rack Offset File + (Accuracy problem on A2001 was traced to a … Accuracy problem on A2001 was traced to a non-linear rack. This tutorial demonstrates how to test the linearity of a rack and the systems in place to correct the linearity.

Modifying the linearity of a rack is a very complex and sensitive issue. You must be absolutely certain that there is a case for linearity with REPEATED tests that produce the same result. It is far more likely that accuracy problems are cause by other mechanical issues. This is the only machine in the 20 year history that has needed these alterations

machine in the 20 year history that has needed these alterations</div> </div>)
ZX5 - ZX3 Hepco alignment Module E Saw Infeed + (Alignment and check procedure for mounting … Alignment and check procedure for mounting of hepco rail To main frame Parts required B0001102 hepco rail D0015492 5 off vertical adjustment plate D0015493 5 off Lateral adjustment plate D0015072 1 off Carriage Plate B0000184 journal wiper 4 off B0000185 journal 2 off B0000186 journal 2off Hepco Levelling Jig Hepco rail v block jigs Hepco rail Drive rack pitching jigk jigs Hepco rail Drive rack pitching jig)
ZX5 Production R0015040 Module F to R0015001B Module E alignment + (Alignment criteria and steps for correct machine installation)
ZX5 Production R0015139 Module B to R0015000B Module C alignment + (Alignment details and level settings for correct alignment of module B to module C)
R0000728 R0000729 Stroke Assembly Dismantling + (Assemblies fitted to MK1 ZX4 will require … Assemblies fitted to MK1 ZX4 will require refurbishment at some point of life cycle. The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools Required''' Standard hex key set Standard spanner set Double pin saw flange spanner Drifts and punches Ballpein hammer Soft hammer Degreasing bath
pein hammer Soft hammer Degreasing bath )
Saw machining centre alignment and level check points +
Commissioning - Z-Block Calibration + (Commonly used during sawing on Z transoms, … Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing. There are 6 possible states the z block can be in. Each of these can have a different length of protrusion for different profiles. 12 x M8 Screws 12 x M8 Nuts 12 x wire numbers 1 - 6ws 12 x M8 Nuts 12 x wire numbers 1 - 6)
R0000711 Rotary Base Assembly REV2 + (Detailed steps to correctly install rotary … Detailed steps to correctly install rotary gear and journals Checks for correct installation of oil feed system Tolerance limits and requirements '''Tools Required''' Standard hex key set 0-25mm micrometer Ring support blocks for assembly Work Table Mag Base and D.T.I Hepco flat spanner 17mm socket Torque Wrench '''Parts required''' D0006423-2mod Drive ring x 1 D0007651 Face plate x 1 B0000185 journal x 6 B0000186journal x 2 D0006503 Journal washer x 8 D00007692 wiper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1iper x 4 D0006521 x2 D0007693 x 2 D0007713 rotary ring cap x 1)
ZX5 Production R0015122 Module A to R0015139 Module B alignment + (Details and steps for correct alignment of Module A to Module B '''Tools Required''' Laser Level 300mm rule 1 meter yellow level 24mm spanner Permanent marker Pipe cutters Ring main connection equipment)
ZX5 Production R0000548E Module G to R0015040 Module F alignment + (Details for correct alignment of module G to module H To include fitting of front safety tray once module G is installed)
R0000204 Notching gear boxes assembly + (For longevity and correct running , it is … For longevity and correct running , it is imperative these units are assembled to the correct tolerances and assembled in the way detailed by this procedure Tools required Standard Hex Key Set Castle nut spanner Loctite 243 thread lock Loctite 641 bearing fit Mandrel jig Grease applicator Fe10 solvent spray
ease applicator Fe10 solvent spray )
J0001000H Autoflow Mk4 Mechanical installation-Alignment + (Information to clarify correct process for installation of J0001000H Autoflow Mk4 Levelling tolerance of 0.004" /0.1mm over 300mm (1 division on engineers level) must be adhered to)
Ecoline Site Installation Guide + (Installation of an Ecoline is quite straig … Installation of an Ecoline is quite straight-forward as all of the main levelling and alignment is taken care of inside the main module housing. Installation involves 3 steps # Levelling main module # Attaching and Levelling Infeed Frame # Refitting Infeed coverling Infeed Frame # Refitting Infeed cover)
Setting Motor Overload Relays + (It is important to set the Motor Overload … It is important to set the Motor Overload Relays to the correct values according to the motor as if the current is set too low, the motor will continually trip the MCB and if it set too high then the motor will not trip the MCB under fault conditions, leading to the motor burning out.ditions, leading to the motor burning out.)
ZX5 Installation Procedure 2023 + (Key data for installation of ZX5 Dokit to generate consistency of installation Quality checks for installation Manufacturing data supply)
ZX5 Installation Procedure 2023 Part 2 + (Key data for installation of ZX5 Dokit to generate consistency of installation Quality checks for installation Manufacturing data supply)
ZX5 Installation Procedure 2023 Part 3 Guarding Conformity checks + (Key data for installation of ZX5 Dokit to generate consistency of installation Quality checks for installation Manufacturing data supply)
TB0301 Autoflow Saw Head Reinforcement - Additional Enhancements + (On Autoflow 2 Sawing Centres following 5 y … On Autoflow 2 Sawing Centres following 5 years of use., it has been found that the internal saw centre framework can lose its rigidity. this is probably due to "bruising" or denting of the aluminium joints introducing a slight amount of play. This is exacerbated by the design where it is attached and driven on from the base up A retrofit kit of parts has previously been created to allow additional reinforcement to be introduced within the structural framework. This kit builds upon the first kit to provide further accuracy enhancements by #Adding left right stability with additional slide rails at the top of the subframe #Adding front / back stability by moving the SY axis leadscrew to the same height as the saw table ====Parts required: ==== R0010272 Kit: Saw Frame Rigidity Pt 2 This kit consists of 2 carriage assemblies, specifically designed to provide further rigidity to the top of the Saw Head Assembly. In addition, 2 mounting blocks required to relocate the Saw Y Axis Assembly are also included. This allows the Saw Y Axis Assembly to continue to operate accurately, but improves the life of associated components. See also [[TB0259 Autoflow Saw Head Reinforcement]][[TB0259 Autoflow Saw Head Reinforcement]])
ZX5 V Notch Blade Mechanical Setup + (On previous models the V notch separation … On previous models the V notch separation was set via the software. This could be quite time consuming and required multiple tests and measurements to get it right. Four variables were used for each V notch and it is not straight-forward to get the shape, depth and position correct. On the new ZX5 the '''shape''' of the V notch is set mechanically and once set it should never need changed again, but remember that some customers sharpen their V notch blades instead of replacing them. The following was carried out on the rear V notches using some standard outerframe but the process is exactly the same for the front. Once set you can use the usual software settings to increase/decrease depth and to align back to back. The overall process is: # Set the shape of the V notch (Mechanical adjustment) # Set the Depth of the V notch (Software adjustment in Notching Tab) # Set the Position of the V notch (Software adjustment in Notching Tab)

...As you WILL have to stand inside the machining centre I would advise the use of a bump cap and gloves as you will be in close proximity to the V notch blades and tooling.

you will be in close proximity to the V notch blades and tooling.</div> </div>)
Updating Baldor ESB Firmware 2022 + (Since 2022 ABB have removed the simple lin … Since 2022 ABB have removed the simple link from workbench to allow firmware download. This makes it trickier to upgrade an ESB unit on a saw side of a flowline to allow CANopen communication. This is needed on a Windows update. The procedure demonstrates where to find the firmware file and how to download to the ESB manuallyle and how to download to the ESB manually)
Changing Main Saw Blade + (Stuga recommends this blade be changed aft … Stuga recommends this blade be changed after 1-2 weeks of cutting - symptoms to determine if the blade needs changing: * Awful cutting sound / smell * Profile dragging (sizes too short) * Brown burnt swarf * Smoke coming out of profile end while cutting

...The 500mm blade is sharp and can be awkward to manouver out of the saw, please be careful

p and can be awkward to manouver out of the saw, please be careful</div> </div> )
ACEpc Changing IP address using netedit + (The ACEpcs use two different systems for c … The ACEpcs use two different systems for connecting a network #NETBeui - this was used on earlier machines but reliability depends on the customer network setup. Reconfiguration after initial setup is difficult #IP addressing - A setup system was written using IP addresses to connect. This is a little harder to set up, but is easier to change later. A special program called netedit was written which updates all the correct files in the backgroundes all the correct files in the background)
Guide to Fitting Eject Push Sensors on ZX Machines + (The Eject Push bar on the Saw Outfeed on t … The Eject Push bar on the Saw Outfeed on the ZX machines does not have sensors fitted to monitor the position of the cylinders. This causes an issue when the bar is obstructed and either does not fully extend or not fully extract. The cycle is not aware of the position of the cylinders and the machine will continue to run, often resulting in a collision. Not having sensors fitted also means that the Eject Push cycle is run via a timer. However, using a timer means that the system does not know the actual position of the cylinders. Having sensors fitted to the cylinders will allow us to have a cycle that monitors the position of the cylinders and we can determine the cycle has finished before allowing another operation to proceed. We can also use the sensors as feedback to stop the machine if the cycle fails. This will result in fewer collisions and damage to parts or products.
s and damage to parts or products. )
GE Control Components Changeover + (The GE control components are now obsolete … The GE control components are now obsolete and we have had to find a new manufacture to use. We have decided to go with Eaton control equipment for this. We are using the same supplier for these products and we have the added benefit if the supplier holding these parts in there stores. We had a choice to use either ABB, Eaton or Schneider components. Although all of the individual Eaton components are a direct replacement for the GE components, there are certain situation that we may be tripped up. This includes times when we need to change a motor breaker that has an auxiliary block connected to it. We can change the breaker but the GE auxiliary block will not fit on the new Eaton one. This means that the Eaton components need to have different part numbers to the GE components. This document will layout the new part numbers and what they relate to and instructions on how they are added and changed in the Sage system. are added and changed in the Sage system.)
ZX5 Alignment Check + (The ZX5 machine can be tricky to align as there are many adjustments designed into the table to offset manufacturing tolerances. This step by step guide follows the correct protocol to ensure the starting point and sequence of alignment is correct)
Repairing R axis datum pin + (The datum pin on the old ZX4 at Sidey was … The datum pin on the old ZX4 at Sidey was recommended to be changed at my last service visit. Unfortunately there are quite a few different datum spindle plates and we were having problems tracking down the correct one so it was decided that I would be sent out the new replaceable datum pin carrier as Sidey have a small machine shop I could use to modify the existing plate to make it fit. Unfortunately the mounting holes of the new carrier interfered with the mounting holes of the pneumatic cylinder so it couldn't be used. After taking dimensions of the existing plate for identification I realised there was actually a very small and quick repair that could be carried out until the correct parts were identified. All you need is a cordless drill, a 2.5 and a 3.1mm drill, M3 tap and an M3 x 15mm cap head screw.l, M3 tap and an M3 x 15mm cap head screw.)
R0000299 Stroke assembly rebuild Part 2 + (The following instructions should be follo … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)
Stuertz Infeed - Align and dowel GX rack + (The rack on a Stuertz infeed is a helical … The rack on a Stuertz infeed is a helical type and is supplied unpinned, as the motor is not connected before delivery to Stuga The alignment must be checked then dowelled with 5mm roll pins The racks are already located in the "Y" direction with location pins, this procedure is purely to align the racks to each other in the GX directionhe racks to each other in the GX direction)
WinMulti - Changing The Colour Identification Box + (The version 6 software has a feature to id … The version 6 software has a feature to identify the colour of the profile and also to help operators load foiled profile in the correct orientation. Updating the colours is a very simple job that can be done in 2 ways
# Via the Machine Settings->Colours Tab # From Bar Queue whenever a new colour is encountered.
Queue whenever a new colour is encountered. )
Alignment guide using wire line + (This dokit is to help with the use of a wi … This dokit is to help with the use of a wire line to set alignment correctly on mechanical build up. Using a wire line correctly will ensure a very accurate straight line is achieved . Accuracy of + - 1 mm over any distance can be achieved using the following method. Using one incorrectly can also easily be done.! The steps shown can be applied to all types of alignment , when you have a vertical face on components that require aligning. face on components that require aligning.)
R0015146 Pneumatic pipe Installation + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001106 Plug in reducer 12-8mm x 1 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1
12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1 )
R0015146 Pneumatic pipe Installation Part 2 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001106 Plug in reducer 12-8mm x 1 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
R0015146 Pneumatic pipe Installation Part 3 + (This instruction is to incorporate assembl … This instruction is to incorporate assembly R0015033B Module F Wiring loom alongside this See Electrical department for prepared components from above assembly '''Tools Required''' Pipe cutters Pipe identification markers Flush cutters '''Parts Required''' P0000010 6mm 1/8 elbow fitting x 6 P0000046 Fitting: 'Y' Adaptor 6mm x 6 P0000047 Bulkhead Elbow 6mm x 1 P0000159 Fitting: Stem Blanking Plug 6mm x 2 P0000160 Fitting: Flow Controller In Line 6mm x 2 P0000551 6mm inline Quick Exhaust Fitting x 3 P0001030 Fitting: SMC 6mm Equal Tee x 1 P0001008 regulator x 3 P0001009 Regulator nut x 3 P0001106 Plug in reducer 12-8mm x 1 P0001107 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 17 Fitting 12mm equal tee x 1 P0001166 12mm tube to tube elbow x 1)
Importing Picking List from Sage To Monday + (This procedure demonstrates how to use the … This procedure demonstrates how to use the "Sage Hooks" MS Access database to grab the data created in Sage and exort to a spreadsheet. The spreadsheet is then imported into a new Monday board, then copied across to the correct Picking List for the machine build.
Picking List for the machine build. )
Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
ZX5 Transfer Table Crank set up + (This tutorial will show you how to mechani … This tutorial will show you how to mechanically set up the cranks and sensors so that the correct overlaps between the different cranks are achieved. Crank C is the crank on the Machining Centre Outfeed that controls the single pop up. Crank D is also mounted on the Machining Centre Outfeed and controls the pop ups on the Transfer Table. Crank E is the crank on the Saw Infeed and controls the single pop up that moves the profile in to the channel. that moves the profile in to the channel.)
R0019207 Upgrade SR Axis Spigot + (This upgrade utilises upgraded parts to en … This upgrade utilises upgraded parts to ensure a mechanical fix is maintained between the SR axis gearbox and main drive pin , whilst also giving the ability once upgraded for the gearbox to be removed with minimal mechanical time. three main parts will be replaced in this upgrade, obsoleting the removed parts Main components of upgrade D00004019E Turntable Mk5 D0004033E Alignment disc Mk5 D0004147E Turntable shaft Mk5nt disc Mk5 D0004147E Turntable shaft Mk5)
PLC Source Control - Git Credential Manager for Windows Install + (When connecting to the tc3Multi repository … When connecting to the tc3Multi repository on BitBucket.org, some times the validation credentials are not accepted. Check that the password you have is correct, if the problem persists , install or update Git Credential manager for windows to the latest version.manager for windows to the latest version.)
R0000299 Stroke assembly rebuild + ( The following instructions should be fol … The following instructions should be followed to ensure that correct assembly and setting are performed '''Tools / consumables Required''' Standard hex key set Standard spanner set Large adjustable spanner Drifts and punches Ballpein hammer Soft hammer FE10 Solvent Hylomar Gasket '''Parts Required''' Kit R0000299 containing B0000043 Double Angular bearing 15 I?D 35 O?D 15.9 long rubber seal 3 x 2 B0000105 Double Angular Bearing 15 I/D 35 O/D 15.9 Long x 1 B0000335 3ph Brake motor 2 pole 3000rpm x 1 B0000380 Double Angular Bearing 25 I/D 52 O/D 20.6 Long + rubber seal x 2 D0000059 Damper Bridge x 1 D0000062 Damper Bridge Boss x 2 D0007730 ZX4 V Notch Mk1 Spindle Shaft x1 D0007867 Bevel Gear (Left) x 1 D0007868 Bevel Gear (Right ) x 1 D0007873 Motor Gear x 1 D0007874 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 174 Pinion Gear x 1 D0007875 Pinion Shaft x 1 P0000165 damper x 1)