Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.
Liste de résultats
- TB0428 Connecting To Yaskawa with Silex USB + (== What is the Silex DS-510? == The Silex … == What is the Silex DS-510? == The Silex unit is a USB server, allowing a PC to have a USB port anywhere over an ethernet network. This is useful to connect the PC to a Yaskawa inverter when they are located in different cabinets. The software sets up a virtual USB port which can then be used to run the Yaskawa DriveWorks software.ed to run the Yaskawa DriveWorks software.)
- Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3 + (<div class="annotatedImageDiv" typeof=" … Autoflows from A2001 to A2015 were initially produced with TwinCAT2 software. This has now been superseded with TwinCAT3 which then has the benefit of compatibility with version 6 front end software.
The original PC cannot be used because
*It is not powerful enough to run v6 front end
*The operating system cannot be upgraded to Windows 10
*It cannot be upgraded to TwinCAT3
The Beckhoff C6015 PC has been chosen to be the replacement PC. It is compact, yet powerful enough to run the v6 front end and TwinCAT in the same
. It has an upgrade to 1.9Ghz 4 core processor.
Because it has a limited 40Gb SSD memory, a compact 64Gb memory stick is inserted into the USB 3.0 port. This acts as a separate drive for the DDRIVE dynamic storage for all machine setup. The internat drive is for the Operating System only. This mimics the current Autoflow setup of a remote Camera PC, hence the camera PC can be retired after the upgrade
era PC, hence the camera PC can be retired after the upgrade<br/>) - R0015341 Bench Assemble Electrical Cabinet with Pneumatics and controls + (<nowiki>'''<u>Tools required&l …
'''Tools required''' ;P0001070 Valve Base: Type 41 6 Position Ø6 x 2<br /><br />P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8<br /><br />P0001101 Male straight 12mm to 1/4 bsp x 5 <br /><br />P0001102 Male elbow 12mm to 1/4 x 2<br /><br />P0001186 Valve 24v dc SMC x 12 <br /><br /><br /><br /><br/></nowiki>)
Tape rule
Steel rule
standard hex keys
Standard HSS drill set
Standard Tap set
Hack saw
Ball Pein hammer
Centre punch
'''Part Required'''
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 3
P0000024 Fitting: Hex Nipple 1/4 BSP x 1
P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2
P0000097 Fitting: Elbow Adaptor 8mm - 1/4 BSPT x 1
P0000159 Fitting: Stem Blanking Plug 6mm x 3
P0000160 Fitting: Flow Controller In Line 6mm x 2
P0000279 Female Cross 1/4'' NPT x 1
P0000297 HighLow Pressure Valve x 1
P0000419 Air Service Unit OH (P0283)x 1
P0001070 Valve Base: Type 41 6 Position Ø6 x 2
P0001074 Fitting: 1/4" BSP Hex Head Silencer x 8
P0001101 Male straight 12mm to 1/4 bsp x 5
P0001102 Male elbow 12mm to 1/4 x 2
P0001186 Valve 24v dc SMC x 12 - R0015114 Bench Assemble Valve Banks and Regulators + (<nowiki>'''<u>Tools Required&l …
'''Tools Required''' <br />P0001071 Valve base type41 8 position x 1<br /><br />P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4<br /><br />P0001101 Male straight 1/4 bsp to 12mm x 2<br /><br />P0001102 Fitting male elbow 12mm 1/4 x 4<br /><br />P0001105 Bulkhead straight 12mm x 6<br /><br />P0001186 Valve. 24v dc smc x 8<br /><br /><br/></nowiki>)
Standard hex key set
Standard spanner set
Standard HSS drill set
Standard tap set
'''Parts Required'''
H0007998 Regulator internal mount 5 way x 1
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 14
P0000020 Fitting: Plug 1/8" BSP (Grubscrew Type) x 9
P0000021 air gun assembly x 1
P0000024 hex nipple 1/4 x 3
P0000058 Regulator Mounting Kit x 1
P0000074 Elbow Adaptor 8mm - 1/8 BSP (Pneumax not acceptable) x 2
P0000096 Fitting: Brass Reducing Bush 1/2 - 1/4 x 2
P0000142 Elbow Adaptor 8mm - 1/8 BSP x 2
P0000145 tee equal 1/4 x 3
P0000159 Fitting: Stem Blanking Plug 6mm x 2
P0000277 Fitting: Bulkhead Female 8mm x 1/4 BSP x 1
P0000278 Regulator 0-2 bar x 1
P0000332 Regulator with Gauge G1/8'' 0-8 bar x 8
P0000361 1/4'' Male Probe to suit 1/4'' PCL Female coupling x 1
P0000419 Air Service Unit OH (P0283) x 1
P0001071 Valve base type41 8 position x 1
P0001074 Fitting: 1/4" BSP Hex Head Silencer x 4
P0001101 Male straight 1/4 bsp to 12mm x 2
P0001102 Fitting male elbow 12mm 1/4 x 4
P0001105 Bulkhead straight 12mm x 6
P0001186 Valve. 24v dc smc x 8 - R0015347 Bench Assemble Duplex extraction unit + (<nowiki><u>'''Tools Required'' …
'''Tools Required''' t;br /><br />M0000274 Extraction Unit Duplex 2off 8' Bags (No Starter) 1850mm x 1 <br /><br />M0000036 ear defence sticker x 1 <br /><br /><br/></nowiki>)
Standard Spanner set
Lifting platform
standard screwdriver set
'''Parts Required'''
M0000151 Extractor Poly Bags 700G 31.5'' Layflat 50'' Long x 2
M0000274 Extraction Unit Duplex 2off 8' Bags (No Starter) 1850mm x 1
M0000036 ear defence sticker x 1 - R0015350 Fit Rigid Ducting + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Duct tape
'''Parts Required'''
M0000116 Ø200mm to 3 way (Ø125mm) extractor pipe connector x 1
M0000118 Ø200mm - 90 deg Bend Ducting x 1
M0000185 Ø125 mm ID 45 degree bend x 1
M0001045 Rigid Ducting Ø125 x 1000mm x 2
M0001213 Rigid Ducting Ø200mm x 500mm x 2
M0001214 Rigid Ducting Ø200 x 2000mm long x 3
M0001228 Extraction Unit inlet taper x 3
mm long x 3 M0001228 Extraction Unit inlet taper x 3 <br/>) - R0015041 Bench Assemble Top Hood Assembly + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard spanner set
Standard Hss drill set
Standard tap set
Acoustic foam cutting board and straight edge
Utility Blade
'''Parts Required'''
Pre wired light, beacon and network cable from electrical department
C0001152 Camera: HikVision DS-2CD2343G0-I-2.8mm x 1
C0001239 Micro SD Card 32Gb Class 10 x 1
D0000770 Door Hinge (M0016) x 2
D0001877 Saw Top Door Mk4 x 1
D0004641 Hinge Pin Block (D7445) x 1
D0004642 Flap Counterbalance Bar x 1
D0004645 Safety Flap Hinge Pin x 1
D0004679 Flap Stiffening Bar x 1
D0004705 Flap Hinge Bar x 1
D0004747B top door screen x 1
D0004807 Flap x 1
D0007445 Hinge Pin Block OH (D4641) x 1
D0016251 Saw Hood Switch Mount Plate (Bernstein) x 1
E0000275 Button: Base Fixing 1 N/C x 1
E0001072 Emergency Stop Module Bevelled 1NO 1NC x 1
E0001569 Guard Lock Switch: Bernstein Radius Actuator (Key) x 1
H0004643 4mm Axxis Clear 145mm x 690mm x 1
M0000002 12mm Grey Acoustic Foam with Black PVC Facing x 1 (consumable stock )
M0000036 Sign - Ear Protection x 1
M0000048 Gas Spring 15mm x 100mm x 1
M0000539 Handle Black Nylon 200mm M8 Fixings x 1
100mm x 1 M0000539 Handle Black Nylon 200mm M8 Fixings x 1 <br/>) - TB0314 Updating Mint File in Workbench + ( * Updating software can be very complicat … * Updating software can be very complicated, so care must be taken and always ensure there is a route to retrace your steps in the event of a failure – with Baldor .mnt files this is easy because each version is a separate file and therefore easy to load the old one back in again * In general, the Baldor (.mnt) software has been designed to be backwards compatible, but there are a few steps that needed to be taken that made this impossible. In these cases, the front end software (winMulti or winSaw) also needs to be updated – you will get an error to tell you that this is the case * Version numbers have always followed a numerical order, so the higher the number, the later the version * Mnt files should always be stored in ** c:\multi on MH side – called Multi X.xxx.mnt ** c:\saw on Saws or Saw side of flowline – called IgSaw X.xx.mnt aw side of flowline – called IgSaw X.xx.mnt )
- Setting Up Windows PC C0000422-KIT 2023 + (<div class="icon-instructions idea-icon … stuga.dokit.app/wiki/Setting_Up_C0000422-KIT_-_Full_Hardware_2023</div> </div>)
- TB0444 Renewing CF Card on TwinCAT2 Systems + (<u>Problem</u> These machines … Problem These machines use a CX5020 PC with a 2Gb CF card running TwinCAT2 PLC system. The CF card can fail, which is effectively the windows operating system. The CF card has a very small capacity, so needs to be created from an image. This TB outlines the steps in the process to ensure a successful conclusion. 1. Create a new CF card at stuga using the beckhoff imaging tool on a CX5020 2. Boot up with the CX5020 3. Ensure PLC is set to Enable on start-up (default is config mode) 4. Rename the PC 5. Install TeamViewer host v10 or less from a USB stick 6. If you have a copy of the version of winMulti it was running, copy this in to the c:\ multi folder. If not, a “'''''new version install'''''” will be needed so copy in data from the g:\builds\PC Installs\Autoflow\Multi folder 7. Set up and customer specific network parameters to ensure TeamViewer will work when it is plugged in on site 8. Send to customer Once on site, follow procedure A if the winMulti version is preserved, or B if it is a '''''new version install'''''eserved, or B if it is a '''''new version install''''')
- TB0449 Ecoline Clearing out Old Archived Data + (= Problem = Software takes a long period of time to find bar after scanning barcode.)
- TB0428 Connecting To Yaskawa with Silex USB +
- Monday - Getting Started For Engineers + (==Why Change?==
*mHelpdesk limitations
** … ==Why Change?==
*mHelpdesk limitations
**Cludgy to use
**Slow response
**Cannot connect to other apps or emails
*Monday advantages
**Easier and more elegant to use
**More configurable
**easy to email into
**Better searching
**Expandable to whole business
**Cheaper
==Similarities to mHELPDESK==
*Monday consists of a set of user definable “Boards” that contain a list of “Pulses”.
*The “pulses” can be configured however we like.
*I have created a “Board” called “Service Jobs”
*On the Service Jobs Board, I have designed the “Pulses” to mimic the service jobs, so this will include the machine, the status, the type classification, etc
*Any pulse has associated “Updates”. These are just like the “items” on an mHelpDesk job, but is much more flexible than the plain text of mHelpdesk
*The service team will assign jobs as before
*The job should be updated by yourself during your visit
*The database of jobs is searchable so you can find the machine history
so you can find the machine history <br/>) - VM Upgrade Software + (As an alternative to having a separate camera PC. Adding a VM (Virtual Machine) to the Front end allows access to the BE and cameras without interrupting the operator.)
- Saw machining centre alignment and level check points + (Bullet pointed checks to determine correct alignment of key components within Sawing unit)
- Disabling a Tool Home or Tool Out Sensor + (If there is a failure of a tool out or too … If there is a failure of a tool out or tool home sensor on the Stuga spindle ring, it is important to be able to quickly disable the input so the machine can continue production until the problem can be properly resolved. The software has an inbuilt functionality to do this - this tutorial takes you through the necessary stepsrial takes you through the necessary steps)
- Commissioning - Off-Cut Laser Sensor + (Infeed Off-Cut Laser sensors are used to c … Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.be larger that the final triggered sensor.)
- Ensuring Mapped Drives Connect Every Time on Startup + (Never found out why but seems Windows tries to manage the Mapped Drives before The Network Service is up and running)
- Move SR Datum Sensor to Higher Level R0019217 + (On a Mk4 Autoflow, The SR axis daum sensor … On a Mk4 Autoflow, The SR axis daum sensor is originally located at the rear and to the base of the SR axis. This area is prone to offcuts, so a new location has been designed at the top, with the following design parameters
*Easy to retrofit
*Sensor is protected in a case
*Short distance to connection box
*Uses existing mounting holes
*Easy to adjust and maintain
*Sensing end location should be vertical onto a plate, not horizontal on to a radiused surface
*Can use E0000336 2mm range sensor reliably
*Incorporate a front fence to help deflect offcuts down the chute and to protect the sensor
The parts are supplied in Kit R0019217B
illustrated here are from a Right to Left feed machine. Parts are unhanded so can be fitted to either hand machine</div> </div><br/>) - ZX5 V Notch Blade Mechanical Setup + (On previous models the V notch separation … On previous models the V notch separation was set via the software. This could be quite time consuming and required multiple tests and measurements to get it right. Four variables were used for each V notch and it is not straight-forward to get the shape, depth and position correct. On the new ZX5 the '''shape''' of the V notch is set mechanically and once set it should never need changed again, but remember that some customers sharpen their V notch blades instead of replacing them. The following was carried out on the rear V notches using some standard outerframe but the process is exactly the same for the front. Once set you can use the usual software settings to increase/decrease depth and to align back to back. The overall process is: # Set the shape of the V notch (Mechanical adjustment) # Set the Depth of the V notch (Software adjustment in Notching Tab) # Set the Position of the V notch (Software adjustment in Notching Tab) you will be in close proximity to the V notch blades and tooling.</div> </div>)
- Updating Baldor ESB Firmware 2022 + (Since 2022 ABB have removed the simple lin … Since 2022 ABB have removed the simple link from workbench to allow firmware download. This makes it trickier to upgrade an ESB unit on a saw side of a flowline to allow CANopen communication. This is needed on a Windows update. The procedure demonstrates where to find the firmware file and how to download to the ESB manuallyle and how to download to the ESB manually)
- Installing VNC Server and Viewer + (Teamviewer are withdrawing support and are … Teamviewer are withdrawing support and are very dismissive of helping out with teamviewer issues for older operating systems. Sometimes the problem just has to be solved, so there are other tools that can be used to "piggy back" onto a teamviewer connection to an office PC. A reliable, free and simple method is to use VNC. This involves #Installing VNC Server on the old PC that you want to control #Installing VNC Viewer on the Piggy-back PC VNC Viewer can be downloaded [https://archive.realvnc.com/download/get/786/eula/ here] VNC Server can be downloaded [https://archive.realvnc.com/download/get/775/eula/ here]e.realvnc.com/download/get/775/eula/ here])
- ACEpc Changing IP address using netedit + (The ACEpcs use two different systems for c … The ACEpcs use two different systems for connecting a network #NETBeui - this was used on earlier machines but reliability depends on the customer network setup. Reconfiguration after initial setup is difficult #IP addressing - A setup system was written using IP addresses to connect. This is a little harder to set up, but is easier to change later. A special program called netedit was written which updates all the correct files in the backgroundes all the correct files in the background)
- Guide to Fitting Eject Push Sensors on ZX Machines + (The Eject Push bar on the Saw Outfeed on t … The Eject Push bar on the Saw Outfeed on the ZX machines does not have sensors fitted to monitor the position of the cylinders. This causes an issue when the bar is obstructed and either does not fully extend or not fully extract. The cycle is not aware of the position of the cylinders and the machine will continue to run, often resulting in a collision. Not having sensors fitted also means that the Eject Push cycle is run via a timer. However, using a timer means that the system does not know the actual position of the cylinders. Having sensors fitted to the cylinders will allow us to have a cycle that monitors the position of the cylinders and we can determine the cycle has finished before allowing another operation to proceed. We can also use the sensors as feedback to stop the machine if the cycle fails. This will result in fewer collisions and damage to parts or products.
s and damage to parts or products. <br/>) - ZX5 MH Infeed Basic IO Test and Setup + (The MH infeed on a ZX5 is a module which c … The MH infeed on a ZX5 is a module which can be tested individually away from the fully installed machine. Once build stage is complete, to be able to test individually, the Infeed Module needs: - To be connected to mains power & be powered on - An air supply to the main blue line - Network connection (Network Cube) - HDMI & Keyboard dongle to be plugged into the Beckhoff PLC inside the cabinet. Input and output activation when testing the sole module is done through the Twincat project rather than through WinMulti The above is only required If the Machine is not fully installed and connected with power air and network already. The below guide is specifically for a fully installed and connected infeed.ically for a fully installed and connected infeed.)
- TB0447 ZX5 Setup - X Axis Beam Calibration + (The ZX5 has a moveable Beam on the Z axis. … The ZX5 has a moveable Beam on the Z axis. The design reason behind this is to keep the gripper arm short for reliability and stiffness, yet enable it to move out of the way for rear V notching During the calculations for the machining bar recipe, the software has to work out if and when the beam needs to be moved: · If there are no v notches on the bar, then machine all the operations without moving the beam. Beam moves at the very end when ejecting · If there is a V notch, move the bar during the first X axis position where position > beamStrokeLength Therefore, it is very important for the software to know how far the beam moves physically to offset all the positions to allow for it. The distance is measured and entered into parameter beamStrokeLength. It should be around 700mm. beamStrokeLength. It should be around 700mm.)
- ZX5 Adjusting V Notch Depth and Position + (The ZX5 has a twin blade system for the V … The ZX5 has a twin blade system for the V notches that is designed to be easier to set up. The overall process is: # Set the shape of the V notch (Mechanical adjustment) # Set the Depth of the V notch (Software adjustment in Notching Tab) # Set the Position of the V notch (Software adjustment in Notching Tab)otch (Software adjustment in Notching Tab))
- TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The ZX5 has two bar measuring systems – th … The ZX5 has two bar measuring systems – the side laser and the sensor array. The side laser scans the bar as it moves into the final loading location, which gives the software a “heads-up” for the length of the bar. If the length is different to expected, the software will then use the sensor array to measure the bar length. There are 2 measurement methods because the side laser is not 100% reliable, especially on shorter lengths below 3000mm. However, it does mean the system does not have to grip and measure / reoptimize each bar length, so improves the cycle time. The sequence is as follows 1. During the conveyor loading, measure the length using the side laser 2. Once loaded to backfence, check the backfence sensor array. 3. If the sensor array rough measurement does not match the laser – a. If the laser measured length < infeedLaserRemeasure, continue and measure with rear sensors b. If the laser measured length < infeedLaserRemeasure, flag an error that laser has not measured correctly. c. If it does match, use the laser value to reoptimize the bar if it is different than expected 4. Load and Grip bar, if necessary, measure accurately with rear sensor arrayssary, measure accurately with rear sensor array)
- Setting Arrow Heads on ZX5 or ZX5-E + (The Zx5 and Zx5e have an upgraded system o … The Zx5 and Zx5e have an upgraded system on the saw centralising which takes the best mechanical features of the standard saw centralising, yet adds an ability to move the central point for Y notches.
In general, this makes it easier to set up, because the overall centralise position can be changed in software , rather than adjusting a cylinder offset, and also to fine tune the centralise position for different profiles
the arrow head position permanently will also alter Y notch depths</div> </div><br/>) - TB0422 Commissioning ZX5 Software 2018 + (The first step in commissioning a new mach … The first step in commissioning a new machine is to get the basic software setup correctly installed. Because the software is designed to be very flexible across many machine types, the simplest way to do this is to copy from a recently built similar machine.opy from a recently built similar machine.)
- X252 Forward Clamp Out Sensor Setup Stuertz Infeed + (The out sensor used for the vorlaufwagen c … The out sensor used for the vorlaufwagen cannot be a standard reed switch because the cylinder that drives this output is a telescoping version. It is impossible to detect the out position. Therefore, a sensor is fitted that must be programmed to set a high output when it detects the full range has been reached The sensor is a [https://www.pepperl-fuchs.com/global/en/classid_53.htm?view=productdetails&prodid=42559#overview Pepperl+Fuchs VDM28-8-L] Datasheet can be downloaded [https://files.pepperl-fuchs.com/webcat/navi/productInfo/45/452859n.pdf?v=20220926110229 here] '''Function''' The distance measurement device contains one transmitter and one receiver incorporated into a single housing. The transmitter light is reflected back to the receiver from a target. The sensor determines the distance to the target and triggers a switching function or supplies the relevant measured value for processing. '''Assembly instructions''' The sensor can be mounted by means of through holes or by using a mounting bracket or mounting clamp Ensure that the surface is level in order to prevent the housing from becoming distorted when the fittings are tightened. It is advisable to secure the nuts and screws using spring washers in order to prevent the sensor from being incorrectly adjusted. '''Connection''' Connect the device in accordance with the connection diagram in the datasheet. '''Adjustment''' The green LED lights up when the operating voltage is switched on. Adjust the sensor so that the laser point is on the gripper bodyso that the laser point is on the gripper body)
- Stuertz Infeed - Align and dowel GX rack + (The rack on a Stuertz infeed is a helical … The rack on a Stuertz infeed is a helical type and is supplied unpinned, as the motor is not connected before delivery to Stuga The alignment must be checked then dowelled with 5mm roll pins The racks are already located in the "Y" direction with location pins, this procedure is purely to align the racks to each other in the GX directionhe racks to each other in the GX direction)
- VM Upgrade Hardware + (The upgrade is to prep the machine ready for adding a Virtual Mahine (VM) to the setup.)
- WinMulti - Changing The Colour Identification Box + (The version 6 software has a feature to id … The version 6 software has a feature to identify the colour of the profile and also to help operators load foiled profile in the correct orientation.
Updating the colours is a very simple job that can be done in 2 ways
# Via the Machine Settings->Colours Tab # From Bar Queue whenever a new colour is encountered.
Queue whenever a new colour is encountered. <br/>) - Viewing Camera Footage from Hikvision Cameras + (The video footage from a Hikvision camera … The video footage from a Hikvision camera can only be viewed via Windows "Internet Explorer". The camera web page also has the facility to playback and download the recorded images stored on the memory card in the camera.
sion. For reasons unknown, Hikvision have not kept this up to date for the latest drivers (Edge and Chrome)</div> </div> <br/>) - Recovery of Bar Queue following winMulti Crash + (There have been cases of software crashing … There have been cases of software crashing on the Stuga front end software, but the machine will continue to cut the holes and slots on the bar and eject it to the transfer table. This creates the situation that the bar is physically finished, but the software has not registered it as finished. This can lead to confusion for the operator and put the bar queue out of sync, which can lead to wasted profile of sync, which can lead to wasted profile)
- Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
- Setting Up New Printer - GX420d + (This tutorial requires a basic knowledge o … This tutorial requires a basic knowledge of IP addresses - what are they and what are they forork. This is contained in the Saw Parameters - printerIPAddress. </div> </div>)
- Dokit - Editing Work Instructions + (This tutorial shows you how to edit the co … This tutorial shows you how to edit the content of a work instruction, allowing you to
*Add New Steps
*Add numbering and bullets to the text
*Add and crop Photos
*Annotate photos with arrows, numbers and text
*Change step sequence and insert steps
*Add Call-outs and warnings
*Add Links to other websites or other Dokit pages
=Warnings=
a fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...Do not publish anything inflammatory, offensive or illegal</div> </div><br/>) - Fitting Zx5 Crank Upgrade + (This upgrade replaces the crank arm assemb … This upgrade replaces the crank arm assemblies on Z065, Z066 and Z067 with a direct drive system to improve reliability
This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes
></div> <div class="icon-instructions-text">...Motors must be rewired for Delta and NOT Star</div> </div> <br/>) - Replacing Beckhoff PC + (To replace a broken PLC requires the installation of the original project. This project needs to be made aware of the new hardware, along with the Stuga software)
- TwinCat Connection Faults + (We are quite often faced with multiple Axi … We are quite often faced with multiple Axis/Door Open/ Estop faults all being reported at the same time. More often than not this is caused by a bad connection on the TwinCat system somewhere. If there is any dropout of connection at any point in the system it will result in this error. You could spend some time crawling about on your hands and knees, opening electrical cabinets and trying to find the fault manualy, but by using TwinCat we can save some time and effort, and pinpoint the cause almost immediately.and pinpoint the cause almost immediately.)
- WinDelay for Twincat Startup + (When Windows Boots up and WinMulti is star … When Windows Boots up and WinMulti is started the TwinCat PLC is not in Run mode ready for the application. The Run mode of Twin cat normally takes between 70 to 90 seconds.
WinStartDelay is a piece of software which delays Winmulti Starting up until the Amount of Time Delay needed has been run.
of Time Delay needed has been run. <br/>)
Français
English
Deutsch
Español
Italiano
Português