Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.
Liste de résultats
- Updating Zebra Firmware on ZD620 model + (Auto calibration upon Power up on the ZD620 printers only works with V84.20.20Z or above, for this reason we may need to check the firmware version on the Printer.)
- Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3 + (<div class="annotatedImageDiv" typeof=" … Autoflows from A2001 to A2015 were initially produced with TwinCAT2 software. This has now been superseded with TwinCAT3 which then has the benefit of compatibility with version 6 front end software.
The original PC cannot be used because
*It is not powerful enough to run v6 front end
*The operating system cannot be upgraded to Windows 10
*It cannot be upgraded to TwinCAT3
The Beckhoff C6015 PC has been chosen to be the replacement PC. It is compact, yet powerful enough to run the v6 front end and TwinCAT in the same
. It has an upgrade to 1.9Ghz 4 core processor.
Because it has a limited 40Gb SSD memory, a compact 64Gb memory stick is inserted into the USB 3.0 port. This acts as a separate drive for the DDRIVE dynamic storage for all machine setup. The internat drive is for the Operating System only. This mimics the current Autoflow setup of a remote Camera PC, hence the camera PC can be retired after the upgrade
era PC, hence the camera PC can be retired after the upgrade<br/>) - R0015316 V notch Final Assembly Part 2 + (<nowiki>'''<u>Tools Required&l …
'''Tools Required''' BJ3-1 x 2<br /><br />P0001133 Cylinder: Ø50 x 500 x 2<br /><br />P0001134 Floating Joint M18x1.5 x 2<br /><br />P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2<br /><br />P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1<br /><br />P0001142 Adjustable Damper 150mm stroke (3000N) x 1<br /><br />P0001144 Reed Switch Mounting Band for Ø50 cyl x 2<br /><br />R0015084 Bench assemble and Drill Off Swarf chutes<br /><br />V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4</nowiki>)
Standard Hex key set
Standard Spanner set
ZX5 Blade tightening tool
Compressed air connection with regulation (for axis support)
'''Parts required'''
A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2
A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2
B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4
B0000173 Blanking plug foc x 28
B0000426 Linear Rail MSB25 400mm Long (AMT) x 4
D0015156 Saw Bearing Plate x 2
D0015161 Saw Plate x 4
D0015162 Saw Mid Spacer Bar x 1
D0015163 Saw Bearing Spacer Bar x 1
D0015168B Balance Cylinder Bracket x 2
D0015169B Cylinder Rod Bracket x 2
D0015179 Energy Chain Bracket x 2
D0015180 Datum Switch Bracket (VZ) x 1
D0015183 VY Stop x 2
D0015235 VY Datum Switch Bracket x 1
D0015236 VY Energy Chain Bracket - Fixed x 1
D0015237 VY Energy Chain Bracket - Moving x 1
D0015250 Safe Sensor Block x 1
D0015251 Safe Sensor Finger x 1
D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2
D0015452 Scissor Cable Retainer x 1
D0015541 Energy Chain Deflector x 1
D0015704 Energy Chain Support Plate x 1
E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2
E0001185 Elte Saw motor x 4
M0001087 Rubber Bump Stop M6 Ø20x24 x2
P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1
P0000023 Fitting: Hex Nipple 1/8 BSP x 1
P0000026 Silencer 1/4 BSP x 1
P0000050 Fitting: Silencer 1/8'' BSP x 1
P0000077 Straight Adaptor 8mm - 1/8BSP x 1
P0000140 Fitting: Quick Exhaust Valve 1/8" x 1
P0001040 Fitting: 1/8BSP Hex Head Silencer x 2
P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2
P0001133 Cylinder: Ø50 x 500 x 2
P0001134 Floating Joint M18x1.5 x 2
P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2
P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1
P0001142 Adjustable Damper 150mm stroke (3000N) x 1
P0001144 Reed Switch Mounting Band for Ø50 cyl x 2
R0015084 Bench assemble and Drill Off Swarf chutes
V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 - R0015316 V notch Final Assembly + (<nowiki>'''<u>Tools Required&l …
'''Tools Required''' BJ3-1 x 2<br /><br />P0001133 Cylinder: Ø50 x 500 x 2<br /><br />P0001134 Floating Joint M18x1.5 x 2<br /><br />P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2<br /><br />P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1<br /><br />P0001142 Adjustable Damper 150mm stroke (3000N) x 1<br /><br />P0001144 Reed Switch Mounting Band for Ø50 cyl x 2<br /><br />R0015084 Bench assemble and Drill Off Swarf chutes<br /><br />V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4<br /><br /><br/></nowiki>)
Standard Hex key set
Standard Spanner set
ZX5 Blade tightening tool
Compressed air connection with regulation (for axis support)
'''Parts required'''
A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 2
A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 2
B0000046 Slide Base Bearing Block (Straight Grease Nipple) x 4
B0000173 Blanking plug foc x 28
B0000426 Linear Rail MSB25 400mm Long (AMT) x 4
D0015156 Saw Bearing Plate x 2
D0015161 Saw Plate x 4
D0015162 Saw Mid Spacer Bar x 1
D0015163 Saw Bearing Spacer Bar x 1
D0015168B Balance Cylinder Bracket x 2
D0015169B Cylinder Rod Bracket x 2
D0015179 Energy Chain Bracket x 2
D0015180 Datum Switch Bracket (VZ) x 1
D0015183 VY Stop x 2
D0015235 VY Datum Switch Bracket x 1
D0015236 VY Energy Chain Bracket - Fixed x 1
D0015237 VY Energy Chain Bracket - Moving x 1
D0015250 Safe Sensor Block x 1
D0015251 Safe Sensor Finger x 1
D0015440 Spacer: Ø12.7 x 36, M6 tap thru x 2
D0015452 Scissor Cable Retainer x 1
D0015541 Energy Chain Deflector x 1
D0015704 Energy Chain Support Plate x 1
E0000336 Sensor: M8; 2mm, PNP N/O, M8 conn x 2
E0001185 Elte Saw motor x 4
M0001087 Rubber Bump Stop M6 Ø20x24 x2
P0000010 1/8 6mm elbow x 1
P0000022 Fitting: Brass Reducing Bush 1/4 - 1/8 BSP x 1
P0000023 Fitting: Hex Nipple 1/8 BSP x 1
P0000026 Silencer 1/4 BSP x 1
P0000050 Fitting: Silencer 1/8'' BSP x 1
P0000077 Straight Adaptor 8mm - 1/8BSP x 1
P0000140 Fitting: Quick Exhaust Valve 1/8" x 1
P0001040 Fitting: 1/8BSP Hex Head Silencer x 2
P0001041 SMC Reed Switch Mounting Bracket BJ3-1 x 2
P0001133 Cylinder: Ø50 x 500 x 2
P0001134 Floating Joint M18x1.5 x 2
P0001140 Pilot Check Valve: 8mm to 1/4" BSP x 2
P0001141 Fitting: SMC Flow Controller Elbow Ø8-1/4BSP x 1
P0001142 Adjustable Damper 150mm stroke (3000N) x 1
P0001144 Reed Switch Mounting Band for Ø50 cyl x 2
R0015084 Bench assemble and Drill Off Swarf chutes
V0000028B-ZX5 Notching Blade: Ø300 x 96 teeth x 2.8mm pl x 3.3mm kf x24mm x 4 - R0000963E Bench Assemble Z axis Components + (<nowiki><u>'''Tools Required'' …
'''Tools Required''' t;<br />P0000140 Fitting: Quick Exhaust Valve 1/8" x 2<br /><br />P0000145 Tee-Equal 1/4BSP Galvanised x 2<br /><br />P0000200 Elbow Adaptor 6mm - M5 x 2<br /><br />P0000229 Pneumax VDMA 40 x 300 Magnetic x 4<br /><br />P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4<br /><br />P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2<br /><br /><br/></nowiki>)
Standard hex key set
Standard spanner set
Emery tape
Standard HSS drill set
Hand reamer
Standard tap set
'''Part Required'''
B0000086 Ball Bearing 15 D 32 D 9 Long + seals x 4
B0000139 Double Angular Bearing 20 D 47 D 20.6 Long + seals x 2
B0000351 Bearing 40mm O/D 17mm I/D 17.5mm Wide x 2
C0001122K Servo Motor: Beckhoff AM8032-1E10 (Keyed) x 1
D0001926 Servo Drive Coupling M20 (Ø14mm) Beckhoff x 1
D0006501 Z Leadscrew Sleeve x 2
D0007629 Cylinder rod Extension x 4
D0007732 Sprocket Idler Shaft x 2
D0007733 Sprocket Mounting Block x 2
D0008090 Retaining Collar x 1
H0007715 Z Sprocket 33 Teeth 3/8'' pitch x 2
H0007790 Leadscrew Z(Includes Re-balling) x 2
P0000007 Straight Adaptor 6mm - 1/8 BSP tapered thread x 2
P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 2
P0000023 Fitting: Hex Nipple 1/8 BSP x 2
P0000024 Fitting: Hex Nipple 1/4 BSP x 2
P0000026 Silencer 1/4 BSP x 4
P0000051 Fitting: Straight Adaptor 6mm - 1/4 BSPT x 4
P0000140 Fitting: Quick Exhaust Valve 1/8" x 2
P0000145 Tee-Equal 1/4BSP Galvanised x 2
P0000200 Elbow Adaptor 6mm - M5 x 2
P0000229 Pneumax VDMA 40 x 300 Magnetic x 4
P0001038 Fitting: SMC 1/8" BSP to Ø6mm Elbow White x 4
P0001174 Fitting: Pilot Check Valve 1/4" (Flow & ZX) x 2 - R0015082B fencing and guards + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
standard spanner set
Standard HSS drill set
Standard Tap set
1 meter level
Tape measure
Steel rule
'''Parts Required'''
D0008330 Double Door Keep x 2
D0015326 Transfer Gate Upright x 6
D0015333 ZX5 Fence Hinge Spacer x 6
D0015340 Profile Support Plate (Short) x 1
D0015341 Profile support plate mount x 1
D0015349 Safety Hinge Mounting Plate x 6
D0015517 Fence Mounting Section x 28
D0015526 ZX5 Saw Fence Infill x 1
D0015601 ZX5 Saw Fence Support Beam (40x80x550) x 1
D0015606 Fence 10 Support Beam F Slot Fixings. x 2
D0015771 Double Door Keep Spacer x 1
D0015914 Saw Infeed Profile Deflector x 1
D0015962 ZX5 Fence 11 - 1100 x 1850 x 2
D0015963 ZX5 Fence 1 1450 x 1850 x 12
D0015964 ZX5 Fence 3 - 1450 x 1850 Cutout x 1
D0015965 ZX5 Fence 2 820 x 1850 x 1
D0015966 ZX5 Fence 10 927 x 1850 x 2
D0015967 ZX5 Transfer Gate x 3
D0015968 ZX5 Fence 7 642x 1850 extraction holes x 1
D0015969 ZX5 Fence 8 - 1105 x 105 Saw Corner x 1
D0015970 ZX5 Fence 820 x 1105 x 1
D0015972 ZX5 Fence Infill - 65 x 1850 x 1
D0015974 ZX5 Fence 13 - 820 x 1105 Hole for Gate x 1
D0015986 Multi Head Waste Bin Guard x 2
D0016018 ZX5 Saw Cabinet Infill Guard x 1
D0016036 Compliance Guard around Cabinet x 1
D0016037 Compliance Guard - MH to MH Infeed x 1
D0016038 Compliance Guard - MH to MH Out x 1
D0016051 Fence Guard (Crank) x 4
D0016171 Compliance Guard - MH to Transfer Gate x 1
D0016172 Compliance Guard - Saw to Transfer Gate x 1
E0001176 Safety Hinge Switch x 3
E0001177 Hinge (works with E1176 Safety Switch) x 3
F0000299 T Nut Sub Insert M6 (Fat) x 83
M0000029 Cabinet Lock (Triangular) x 4
M0000515 Floor Mouting Angle 200x87x42x 7
M0000516 Adjustable Foot Ø60 M14 x 6
M0001016 Angle 74 x 38 x 6
M0001202 Bruehl Fence Panel 1825 x 2200 x 4
M0001204 Bruehl 2.0m Transit Post x 5
M0001207 Bruehl Fence Clip x 31
R0000901 ZX4 Local Gate x 1
01207 Bruehl Fence Clip x 31 R0000901 ZX4 Local Gate x 1 <br/>) - R0015357 Fit Guards + ('''<u>Tools Required</u>'''
… '''Tools Required'''
Standard hex key set
Standard HSS drill set
Standard tap set
Cutting disc
'''Parts Required'''
C0001275 Printer: ZD421 Direct Thermal (Not Incl. C0001276 P&P)
C0001276 Peel & Present for ZD421 Printer
D0016333 Bruehl Fence panel 1700 x 800 x 2
D0016334 Bruehl Fence panel 650 x 800 x 2
H0005178 Safety Table Extension x 1
M0000033 Frame End Cap 50 x 50 x 1
M0001207 Bruehl Fence Clip x 14
P0000069 Tube to tube fitting 6mm x 1
R0015290 Saw Outfeed Bench Assemble Top guard x 1
fitting 6mm x 1 R0015290 Saw Outfeed Bench Assemble Top guard x 1 <br/>) - TB0314 Updating Mint File in Workbench + ( * Updating software can be very complicat … * Updating software can be very complicated, so care must be taken and always ensure there is a route to retrace your steps in the event of a failure – with Baldor .mnt files this is easy because each version is a separate file and therefore easy to load the old one back in again * In general, the Baldor (.mnt) software has been designed to be backwards compatible, but there are a few steps that needed to be taken that made this impossible. In these cases, the front end software (winMulti or winSaw) also needs to be updated – you will get an error to tell you that this is the case * Version numbers have always followed a numerical order, so the higher the number, the later the version * Mnt files should always be stored in ** c:\multi on MH side – called Multi X.xxx.mnt ** c:\saw on Saws or Saw side of flowline – called IgSaw X.xx.mnt aw side of flowline – called IgSaw X.xx.mnt )
- TB0426 Replacement Zebra Printer Setup + (<div class="icon-instructions caution-i … [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions]iv> [https://stuga.dokit.app/wiki/TB0452_ZD620_Zebra_Printer_Setup ZD620 Instructions])
- OBSOLETE Installing SourceTree Version Control Software + (<div class="icon-instructions caution-i … Use this [https://stuga.dokit.app/wiki/Changing_Version_Control_to_Visual_Studio link] From Jan 2020, Sourcetree will be increasingly used to properly maintain changes to the Stuga source code. Each machine with TwinCAT3 will need the Sourcetree program installed, and a change to where and how the source code is stored This tutorial deals with installing the Sourcetree program from Atlassian code is stored This tutorial deals with installing the Sourcetree program from Atlassian)
- Updating winStugaSaw Software to v4 + (<div class="icon-instructions caution-i …
With the upgrade of the source code editor to Visual Studio 2017, and the associated security changes to Windows, many thing changed with the Windows .net libraries. In order to maintain the code, it needed to be upgraded.
This upgrade had major consequential effects:
# It was not compatible with windows XP any more due to security issues
# A new version of Workbench needs to be installed
any more due to security issues # A new version of Workbench needs to be installed <br/>) - R0015290 Bench Assemble Top guard + (<u>'''Tools Required'''</u>
… '''Tools Required'''
Standard hex key set
Acoustic foam cutting edge and Back board
Stanley blade
Standard HSS drill set
Standard tap set
Step drill
'''Parts Required'''
D0001352 Printer Shelf TLP2844-Z x 1
D0004719E Cut Bar Guard Mk5 (5476E) x 1
E0000249 Sounder Beacon x 1
M0000002 12mm Grey Acoustic Foam with Black PVC Facing x 1
M0001127 Cable Tie Base (m6) x 1
with Black PVC Facing x 1 M0001127 Cable Tie Base (m6) x 1 <br/>) - R0015321 Bench Assemble Guards and Doors + (<u>'''Tools Required'''</u>
… '''Tools Required'''
Standard hex key set
Standard spanner set
Dymo label printer
'''Parts Required'''
C0001152 Camera: HikVision DS-2CD2343G0-I-2.8mm x 3
C0001239 Micro SD Card 32Gb Class 10 x 3
D0007643B Perspex Glazing - Door x 4
D0007644B Machining Centre Door 1 x 2
D0007645B Machining Centre Door 2 x 2
D0007654B Perspex Glazing - Front Guard MkB x 1
H0015747 8mm diameter rod x 1 ( in process of changing to D0015747 x 4 )
M0000036 Sign - Ear Protection x 1
M0000201 T Handle Cabinet Lock x 2
gn - Ear Protection x 1 M0000201 T Handle Cabinet Lock x 2 <br/>) - TB0444 Renewing CF Card on TwinCAT2 Systems + (<u>Problem</u> These machines … Problem These machines use a CX5020 PC with a 2Gb CF card running TwinCAT2 PLC system. The CF card can fail, which is effectively the windows operating system. The CF card has a very small capacity, so needs to be created from an image. This TB outlines the steps in the process to ensure a successful conclusion. 1. Create a new CF card at stuga using the beckhoff imaging tool on a CX5020 2. Boot up with the CX5020 3. Ensure PLC is set to Enable on start-up (default is config mode) 4. Rename the PC 5. Install TeamViewer host v10 or less from a USB stick 6. If you have a copy of the version of winMulti it was running, copy this in to the c:\ multi folder. If not, a “'''''new version install'''''” will be needed so copy in data from the g:\builds\PC Installs\Autoflow\Multi folder 7. Set up and customer specific network parameters to ensure TeamViewer will work when it is plugged in on site 8. Send to customer Once on site, follow procedure A if the winMulti version is preserved, or B if it is a '''''new version install'''''eserved, or B if it is a '''''new version install''''')
- ZX5 - ZX3 Hepco alignment Module E Saw Infeed + (Alignment and check procedure for mounting … Alignment and check procedure for mounting of hepco rail To main frame Parts required B0001102 hepco rail D0015492 5 off vertical adjustment plate D0015493 5 off Lateral adjustment plate D0015072 1 off Carriage Plate B0000184 journal wiper 4 off B0000185 journal 2 off B0000186 journal 2off Hepco Levelling Jig Hepco rail v block jigs Hepco rail Drive rack pitching jigk jigs Hepco rail Drive rack pitching jig)
- Updating Zebra Firmware on ZD620 model +
- Placing a TwinCAT3 Machine Under Source Control + (<div class="icon-instructions caution-i … Click [https://stuga.dokit.app/wiki/Changing_Version_Control_to_Visual_Studio here] for the latest procedure For many years, the source code for the PLCs has resided on the G:\drive and then a copy on each and every one of the PCs used to edit the code, so at least one on each machine. This is a recipe for disaster because maintaining all the copies and version numbers is incredibly difficult and adds a lot of time overhead to fixes and changes. This has worked because there has been only one developer, but this is set to change in future as more programmers will be trained and tracking versions becomes more difficult From 2020, the PLC code version control has been improved by using an industry standard source control system called "Git" along with "BitBucket" to store the PLC code in the cloud. The program "SourceTree" is used to commit, push and pull the changes [https://www.atlassian.com/git/tutorials/what-is-version-control Click here] for an introduction to version control using Git This tutorial is a step by step guide to setting up an existing machine or diagnostic PC to a standard uses on all Stuga machines to enable quick, easy and stress free version control.standard uses on all Stuga machines to enable quick, easy and stress free version control.)
- Full Version Upgrade TwinCAT3 WinMulti + (If a PC fails on a machine in the field an … If a PC fails on a machine in the field and the hard drive data cannot be recovered, it is necessary to replace the PC. This may create a version conflict, as the new PC will have later versions of twinCAT installed than the original
This tutorial outlines the steps required to bring all the machine systems up to the latest level to ensure compatibility
ions-text">...This is a one-way process that cannot be reversed</div> </div><br/>) - Changing Version Control to Visual Studio + (In March 2022 the password policy of the s … In March 2022 the password policy of the system behind SourceTree / Bitbucket and Atlassian changed - [https://community.atlassian.com/t5/Bitbucket-articles/Announcement-Bitbucket-Cloud-account-password-usage-for-Git-over/ba-p/1948231 link]. This meant all machine would need a complex password login change for the SourceTree program used for version control of the PLC code. This was not straight-forward to resolve, so the decision was made to change the version control system to the one that is packaged with the Visual Studio system by default. This is a better method anyway, but it needs the "TcXaeShell" installed. Visual Studio that includes Source control, rebadged for TwinCAT3</div> </div>)
- Commissioning - Off-Cut Laser Sensor + (Infeed Off-Cut Laser sensors are used to c … Infeed Off-Cut Laser sensors are used to check the length of profile with the proposed length from the software. This is to avoid incorrect lengths and profiles being cut. The sensors will be put at specific lengths along the infeed which will be input in the software files. When profile hits the back fence all covered sensors will trigger, hence, the profile must be larger that the final triggered sensor.be larger that the final triggered sensor.)
- TB450 - CMOS Battery replacement + (Internal CMOS batteries are used in PCs to … Internal CMOS batteries are used in PCs to keep a constant power supply to BIOS memory while the main power supply is switched off. These batteries should last up to 5 years when a PC has been left idle. Sometimes these batteries can fall flat before this time either due to being low when sent out or extended use on older machines. The main symptom of a CMOS battery faulting on a Stuga machine is the PC not booting up when mains power is switched on which will be indicated by a “No Signal Detected” message being displayed on the screen. This is due to the BIOS setting “Restore AC Power Loss” going back to its default value of OFF due to the battery faulting. Restoring the BIOS to its original settings is a temporary fix in this situation as it is most likely this will happen again a couple of months down the line (See TB 376 or 213). The battery required is a '''CR2032'''. In the case of the Antec PC, and most commonly, the battery is held in an open housing that can be pushed to release and easily replaced. In PCs such as the Acer Revo the battery needs to be pre-wired with a plug but still easily unclipped and replacedug but still easily unclipped and replaced)
- Monday - Putting Customer Machines On Stop + (It is important that everyone does this th … It is important that everyone does this the same way or confusion and frustration will follow. It is also important to understand how the relationship between a Machine and it’s contract works * Each machine on the “Machine” board needs to link to a “Contract” on the “Service Contracts” board * This allows multiple Machines to have the same “Contract” – eg Customade group contract * The “Contract” is the electronic version or equivalent to the bit of paper that the customer has signed, and contains the start and end dates, etc * For machines that have no contract, I have set up some other “General” contract types. These General Types are not machine specific – ** PAYG – General Pay as you go ** OnStop – Customer is on stop and nothing should be supplied ** AskFirst – Ask KG or management first before supplying goods and services ** Proforma – Payment required before supply of goods and services ** PreDelivery – Before warranty startses ** PreDelivery – Before warranty starts)
- Stuertz Infeed - Check GY Position Parallelism + (It is important that the parallelism of th … It is important that the parallelism of the GY axis to the backfence is set and maintained along the length of the rack. This tutorial describes how to check this parallelism without the need for measuring equipment
Potential Symptoms of a problem
*Gripper cannot pick up offcuts
*Gripper /profile end forced away from backfence
*Accuracy problems
*Gripper wobbles after it has released profile
Use the laptop to enable you to control the Service screen whilst inside the infeed table
Ther gripper setting jig is used to give an accurate and reliable zero to locate the gripper jaw to. Any piece of aluminium reinforcing box section will also work
Create a spreadsheet or a table to log your results,.
ng box section will also work Create a spreadsheet or a table to log your results,. <br/>) - Updating Teamviewer Host + (Older versions of Teamviewer are being pha … Older versions of Teamviewer are being phased out by the Teamviewer company from September 15th 2021. The advice on the website suggests you need to upgrade to version 15. However, v15 is not compatible with the older Windows XP machines in the field. The latest XP compatible downloadable version of the Host program is 13.2 and is available [https://download.teamviewer.com/download/version_13x/TeamViewer_Host_Setup.exe here] Regrettably, the update process on older versions is not simple, and frustratingly cannot be done remotely. It needs intervention from an operator at the machine with a small amount of technical know-how with a small amount of technical know-how)
- Updating Baldor ESB Firmware 2022 + (Since 2022 ABB have removed the simple lin … Since 2022 ABB have removed the simple link from workbench to allow firmware download. This makes it trickier to upgrade an ESB unit on a saw side of a flowline to allow CANopen communication. This is needed on a Windows update. The procedure demonstrates where to find the firmware file and how to download to the ESB manuallyle and how to download to the ESB manually)
- ZX5 MH Infeed Basic IO Test and Setup + (The MH infeed on a ZX5 is a module which c … The MH infeed on a ZX5 is a module which can be tested individually away from the fully installed machine. Once build stage is complete, to be able to test individually, the Infeed Module needs: - To be connected to mains power & be powered on - An air supply to the main blue line - Network connection (Network Cube) - HDMI & Keyboard dongle to be plugged into the Beckhoff PLC inside the cabinet. Input and output activation when testing the sole module is done through the Twincat project rather than through WinMulti The above is only required If the Machine is not fully installed and connected with power air and network already. The below guide is specifically for a fully installed and connected infeed.ically for a fully installed and connected infeed.)
- Updating Beckhoff TwinCAT3 Backend Version + (The TwinCAT3 beckhoff systems have a speci … The TwinCAT3 beckhoff systems have a special version of TwinCAT installed - the "Runtime" version XAR (eXtended Automation Runtime). This differs from the full "Engineering version XAE that is installed in the front end and camera PCs in that it is the bare bones of TwinCAT for machine running purposes. '''It does not have the Visual Studio editor in it.''' The runtime version may need updating to 3.4024.xx to allow the latest front end and PLC code to work the latest front end and PLC code to work)
- TB0447 ZX5 Setup - X Axis Beam Calibration + (The ZX5 has a moveable Beam on the Z axis. … The ZX5 has a moveable Beam on the Z axis. The design reason behind this is to keep the gripper arm short for reliability and stiffness, yet enable it to move out of the way for rear V notching During the calculations for the machining bar recipe, the software has to work out if and when the beam needs to be moved: · If there are no v notches on the bar, then machine all the operations without moving the beam. Beam moves at the very end when ejecting · If there is a V notch, move the bar during the first X axis position where position > beamStrokeLength Therefore, it is very important for the software to know how far the beam moves physically to offset all the positions to allow for it. The distance is measured and entered into parameter beamStrokeLength. It should be around 700mm. beamStrokeLength. It should be around 700mm.)
- TB0445 ZX5 Setup - Infeed Measure Sensor Calibration + (The ZX5 has two bar measuring systems – th … The ZX5 has two bar measuring systems – the side laser and the sensor array. The side laser scans the bar as it moves into the final loading location, which gives the software a “heads-up” for the length of the bar. If the length is different to expected, the software will then use the sensor array to measure the bar length. There are 2 measurement methods because the side laser is not 100% reliable, especially on shorter lengths below 3000mm. However, it does mean the system does not have to grip and measure / reoptimize each bar length, so improves the cycle time. The sequence is as follows 1. During the conveyor loading, measure the length using the side laser 2. Once loaded to backfence, check the backfence sensor array. 3. If the sensor array rough measurement does not match the laser – a. If the laser measured length < infeedLaserRemeasure, continue and measure with rear sensors b. If the laser measured length < infeedLaserRemeasure, flag an error that laser has not measured correctly. c. If it does match, use the laser value to reoptimize the bar if it is different than expected 4. Load and Grip bar, if necessary, measure accurately with rear sensor arrayssary, measure accurately with rear sensor array)
- X252 Forward Clamp Out Sensor Setup Stuertz Infeed + (The out sensor used for the vorlaufwagen c … The out sensor used for the vorlaufwagen cannot be a standard reed switch because the cylinder that drives this output is a telescoping version. It is impossible to detect the out position. Therefore, a sensor is fitted that must be programmed to set a high output when it detects the full range has been reached The sensor is a [https://www.pepperl-fuchs.com/global/en/classid_53.htm?view=productdetails&prodid=42559#overview Pepperl+Fuchs VDM28-8-L] Datasheet can be downloaded [https://files.pepperl-fuchs.com/webcat/navi/productInfo/45/452859n.pdf?v=20220926110229 here] '''Function''' The distance measurement device contains one transmitter and one receiver incorporated into a single housing. The transmitter light is reflected back to the receiver from a target. The sensor determines the distance to the target and triggers a switching function or supplies the relevant measured value for processing. '''Assembly instructions''' The sensor can be mounted by means of through holes or by using a mounting bracket or mounting clamp Ensure that the surface is level in order to prevent the housing from becoming distorted when the fittings are tightened. It is advisable to secure the nuts and screws using spring washers in order to prevent the sensor from being incorrectly adjusted. '''Connection''' Connect the device in accordance with the connection diagram in the datasheet. '''Adjustment''' The green LED lights up when the operating voltage is switched on. Adjust the sensor so that the laser point is on the gripper bodyso that the laser point is on the gripper body)
- WinMulti - Changing The Colour Identification Box + (The version 6 software has a feature to id … The version 6 software has a feature to identify the colour of the profile and also to help operators load foiled profile in the correct orientation.
Updating the colours is a very simple job that can be done in 2 ways
# Via the Machine Settings->Colours Tab # From Bar Queue whenever a new colour is encountered.
Queue whenever a new colour is encountered. <br/>) - Ecoline - Setting V Notches on winMulti Software + (This is the full setup procedure for V not … This is the full setup procedure for V notches on an Ecoline. This should only be needed on initial commissioning or if the shape of the notch has changed due to some physical intervention, for example -
- Blade Change
- Blade buckled
here is no sense carrying on because you cannot complete this setup unless the machine is consistent and reliable</div> </div> <br/>) - PC Bios Power settings + (This power setting enables the PC to Boot … This power setting enables the PC to Boot up automatically when power is first detected, in other words when the power is “lost” and then “returns”, without the necessity to manually press the power button on the PC. The following description shows how to set the auto power-up on but beware this Technical Bulletin only applies to the “ASUS UEFI Utility BIOS Version 2.x.x”. This document is for the ASUS Pcs For the Dell PCs use [[PC Bios Power Settings - Dell]]ttings - Dell]])
- Setting Up C0000422-KIT - Full Hardware 2023 + (This process takes the components to creat … This process takes the components to create a standard "C000422-KIT". This kit can then be stored and pulled off the shelf when required. It will then need to be set up for the particular customer machine using [[Setting Up Windows PC C0000422-KIT 2023]] =Notes= *There are two PCs running on the same hardware, The Host PC and the Virtual machine. **'''Host PC''' (For support) ***The base Windows install running directly on the hardware installed to Dell NVME drive. ***Has its own OEM Windows license supplied by Dell linked directly to the hardware (no product code – stored in the Dell hardware) ***Imaged by Macrium reflect. **'''Virtual PC – Stuga VM''' ***Used for Stuga software - the VM can run on any PC without changing drivers, etc. Host OS version / hardware unimportant as long as it runs Hyper-V. ***A second install of Windows running on a virtual machine, hosted by the Host PC above. It has a dedicated SSD (the Kingston Drive) stored on [:Fichier:///D:/VMPC.vhdx D:\VMPC.vhdx], with 8GB RAM. ***Has its own dedicated Windows 11 PRO license present in the kit, product code stored on Monday and on the license. ***Copied to host and setup manually during install. There is a setup program for the specific client after this process has completed: '''P_Stuga_P… '''on the desktop of the host.'P_Stuga_P… '''on the desktop of the host.)
- Setting Up New Printer - GX420d + (This tutorial requires a basic knowledge o … This tutorial requires a basic knowledge of IP addresses - what are they and what are they forork. This is contained in the Saw Parameters - printerIPAddress. </div> </div>)
- Ecoline - Datum and MitreOffset Tests + (When an Ecoline is commissioned, the posit … When an Ecoline is commissioned, the positional accuracy needs to be set up.
These are also useful tests to check if the machine is maintaining positional accuracy
tent, repeatable results before making any parameter changes</div> </div><br/>) - PLC Source Control - Git Credential Manager for Windows Install + (When connecting to the tc3Multi repository … When connecting to the tc3Multi repository on BitBucket.org, some times the validation credentials are not accepted. Check that the password you have is correct, if the problem persists , install or update Git Credential manager for windows to the latest version.manager for windows to the latest version.)
- Upgrade Flowline Opto Sensors to Ultrasonic + (With the development of full colour ranges for profiles, the older flowline opto sensors often have trouble "seeing" the darker profiles. An upgrade kit is available (R0019014) to replace the optical sensors with an ultrasonic version <br/>)
- Easily resizable forms for any screen resolution in Visual Studio + (if you have issues with certain screen resolutions cropping off buttons and need to design a form which works at all resolutions, and also allows the user to resize parts of the form, then this tutorial will help.)
Français
English
Deutsch
Español
Italiano
Português