Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Liste de résultats

• Upgrading Autoflow TwinCAT2 to Win10 and TwinCAT3  + (infeedZeroToX=605 stopZeroToX=595 measureSensorPos1=1554)

• R0015277 Set Drive pinions in position  + (Use Loctite 243 on all fasteners Use Loctite 572 on all threaded pneumatic connections Pen mark all fasteners to show finalised)
• Changing saw pusher bearings - Standalone Saw  + (Bring the Saw pusher to the end where the chain tensioner and sprocket are. Remove the pusher arm by taking out 2 bolts below the arm. Remove the face plate by taking out the 4 bolts in the fron of the plate Take off the top roller bearings.)
• R0015382 Top Spindle Blower Upgrade  + (Assemble Valve and Y connector as shown)
• R0015280 Module E Pneumatic Tests  + (In this process pneumatic outputs will be … In this process pneumatic outputs will be tested in a non emergency stop environment Ensure safe working practice is followed * Ensure Machine test area is clear from personnel and all staff are aware of testing procedure commencing * Ensure all Air connection lines are connected * Ensure all walkways are not impeded by trailing pipes/leads * Ensure all mechanical assemblies are at a sufficient stage for testinglies are at a sufficient stage for testing)
• R0015085 Mount SR Datum Sensor and Flag  + (All bolts to have Loctite 243 adhesive applied unless otherwise stated All Threaded Pneumatic connections to have Loctite 570 applied All bolts to be pen marked once adhesive applied and correct tension added)
• Test tutorial  + (sdfgsdfgsdfg # one # two #)
• Dokit - Creating A Work Instruction  + (To create a new Dokit, you need to login as a editor The Username is Gareth Green Password is available from the IT department <br/>)
• Full Version Upgrade TwinCAT3 WinMulti  + (https://stugaltd.monday.com/boards/304269981 *Date *Front End Version *Back End Version *BE Firmware *Version Control Type)
• R0015278 Mount Completed Assemblies Section two  + (these steps follow on from dokit [[R0015278 Mount Completed Assemblies]])
• R0000728 R0000729 Stroke Assembly Dismantling  + (The stroke assembly must be dismantled in the exact manner stated as many sections can only be removed once mating parts have been extracted Please use the following steps accurately)
• R0015273 Module E support arm alignment  + (Use locktite 243 on all fasteners Use loctite 572 on all threaded pneumatic connection Pen mark all fasteners to show finalised)
• Setting Gripper Nose  + (when it is in this position - Fully bottom … when it is in this position - Fully bottomed make sure the Grip on comes down but doesn't catch the Grip nose. Notice the Dead stop bolt at bottom is hard up then set grip switch bolt so that the dead stop bolt gap is no more than 1mm when grip switch goes off.o more than 1mm when grip switch goes off.)
• Autocut Startup Procedure  + (Ensure the main isolator on the console is in the on position (pointing up).)
• Updating Realtime Drivers for EtherCAT  + (If you have I/O connected but do not see a device with (EtherCAT) then check that the drivers have been installed.)
• TB0385 Upgrading to winMulti v6  + ( (Defaults to Config mode after the TwinCAT update))
• X252 Forward Clamp Out Sensor Setup Stuertz Infeed  + (Select Q1)
• StuertzCloud - Creating Local SQL Database  + (This is stored on the [https://stugaltd.monday.com/boards/4881973586 Software versions] Monday Board)