Changing Pneumax Valve slice : Différence entre versions

[version en cours de rédaction]

[version en relecture]

Version actuelle datée du 20 septembre 2019 à 09:29

Instructions on how to change a Pneumax valve slice

Auteur Stuga Engineer | Dernière modification 20/09/2019 par Stuga Engineer en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Facile

Durée

5 minute(s)

Instructions on how to change a Pneumax valve slice

Difficulté

Facile

Durée

5 minute(s)

Sommaire

1 Pièces et outils
2 Étape 1 - Undo fixing screws using small pozi Screwdriver.
3 Étape 2 - Removing old Valve Slice
4 Étape 3 - Fitting New Valve Slice
5 Étape 4 - Tighten Screws
6 Commentaires

valve, slice, pneumax, air

Pièces et outils

Pièces et outils

Étape 1 - Undo fixing screws using small pozi Screwdriver.

Please ensure screwdriver is a good fit to avoid wearing the head of the screw.

Étape 2 - Removing old Valve Slice

Pull Valve slice off, holding at the bottom and top of the slice.

When removing the slice be careful not to bend the pins on the slice.

Make sure the Valve Gasket piece does not fall out or go missing. This is needed to stop leaks.

Étape 3 - Fitting New Valve Slice

Ensure pins line up correctly and are carefully inserted. Push valve slice into position.

Étape 4 - Tighten Screws

When tightening the screws, screw in 2 turns on each of the side until tight to ensure a square fit.

...Do not over tighten, the bolts will strip easily

Commentaires

en none 0 Published

@@ Ligne 6 : / Ligne 6 : @@
 |Duration=5
 |Duration-type=minute(s)
+|Tags=valve, slice, pneumax, air
 }}
 {{Introduction
 |Introduction=<translate></translate>
 }}
-{{Materials}}
+{{Materials
+|ItemList={{ItemList
+|Item=Small Pozi Head Screwdriver
+}}
+}}
 {{EPI}}
 {{Tuto Step
 |Step_Title=<translate>Undo fixing screws using small pozi Screwdriver.</translate>
-|Step_Content=<translate>Please ensure screwdriver is a good fit to avoid wearing the bolt head.</translate>
+|Step_Content=<translate>Please ensure screwdriver is a good fit to avoid wearing the head of the screw.</translate>
 |Step_Picture_00=Changing_Pneumax_Valve_slice_IMG_2482.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":640,"height":480,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.94,"scaleY":0.94,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/d/da/Changing_Pneumax_Valve_slice_IMG_2482.jpg","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":446.05,"top":230.75,"width":41,"height":43.5,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":20.501717231030238,"ry":21.749750553164787},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":414.41,"top":345.18,"width":41.64,"height":42.14,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":20.8176552250205,"ry":21.068189209606544},{"type":"wfrect","version":"2.4.6","originX":"center","originY":"center","left":431.9,"top":242.87,"width":72.83,"height":366.22,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":0,"ry":0}],"height":450,"width":600}
@@ Ligne 20 : / Ligne 25 : @@
 {{Tuto Step
 |Step_Title=<translate>Removing old Valve Slice</translate>
-|Step_Content=<translate>When removing the slice be careful not to bend the pins on the slice.
+|Step_Content=<translate>Pull Valve slice off, holding  at the bottom and top of the slice.
-Also make sure the Valve Gasket piece does not fall out or go missing. This is needed to stop leaks.</translate>
+{{Warning|When removing the slice be careful not to bend the pins on the slice.}}{{Info|Make sure the Valve Gasket piece does not fall out or go missing. This is needed to stop leaks.}}<br /></translate>
 |Step_Picture_00=Changing_Pneumax_Valve_slice_IMG_2483.jpg
 |Step_Picture_01=Changing_Pneumax_Valve_slice_IMG_2484.jpg
@@ Ligne 32 : / Ligne 37 : @@
 {{Tuto Step
 |Step_Title=<translate>Fitting New Valve Slice</translate>
-|Step_Content=<translate>Ensure pins line up correctly and are carefully inserted. Push valve slice on. When tightening the screws, screw in 2 turns on each of the side until tight to ensure a square fit. Do not over tighten, the bolts will strip easily.</translate>
+|Step_Content=<translate>Ensure pins line up correctly and are carefully inserted. Push valve slice into position.</translate>
 |Step_Picture_00=Changing_Pneumax_Valve_slice_IMG_2488.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":640,"height":480,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.94,"scaleY":0.94,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/4/44/Changing_Pneumax_Valve_slice_IMG_2488.jpg","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":160.83,"top":330.4,"width":168.67,"height":161.22,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":84.33737147555341,"ry":80.60955473738679}],"height":450,"width":600}
-|Step_Picture_01=Changing_Pneumax_Valve_slice_IMG_2491.jpg
+}}
+{{Tuto Step
+|Step_Title=<translate>Tighten Screws</translate>
+|Step_Content=<translate>When tightening the screws, screw in 2 turns on each of the side until tight to ensure a square fit.
+{{Warning|...Do not over tighten, the bolts will strip easily}}</translate>
+|Step_Picture_00=Changing_Pneumax_Valve_slice_IMG_2491.jpg
 }}
 {{Notes}}
@@ Ligne 44 : / Ligne 55 : @@
 }}
 {{Tuto Status
-|Complete=Draft
+|Complete=Published
 }}