| [version en cours de rédaction] | [version en cours de rédaction] |
| (5 révisions intermédiaires par 2 utilisateurs non affichées) | |||
| Ligne 14 : | Ligne 14 : | ||
This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes | This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes | ||
| − | {{Warning|...The drives must be programmed before parts sent out}}<br /></translate> | + | {{Warning|...The drives must be programmed before parts sent out}}{{Warning|...Motors must be rewired for Delta and NOT Star}} |
| + | <br /></translate> | ||
}} | }} | ||
{{Materials}} | {{Materials}} | ||
{{EPI}} | {{EPI}} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Program | + | |Step_Title=<translate>*IF EATON DRIVES ONLY* Program Drives before they leave</translate> |
|Step_Content=<translate>Running frequency | |Step_Content=<translate>Running frequency | ||
| Ligne 27 : | Ligne 28 : | ||
Decel time | Decel time | ||
| + | |||
[[Programming Eaton DE Drive|https://stuga.dokit.app/wiki/Programming_Eaton_DE_Drive]]<br /></translate> | [[Programming Eaton DE Drive|https://stuga.dokit.app/wiki/Programming_Eaton_DE_Drive]]<br /></translate> | ||
| + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_eaton_de1.JPG | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| Ligne 138 : | Ligne 141 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Remove 2 off | + | |Step_Title=<translate>Remove 2 off motor breakers and contactors from Module C</translate> |
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
|Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0314.JPG | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0314.JPG | ||
| Ligne 144 : | Ligne 147 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Add 2 off single pole | + | |Step_Title=<translate>Add 2 off 10A single pole MCB's in Module C</translate> |
|Step_Content=<translate>Tidy wires away for the spare 2 phases</translate> | |Step_Content=<translate>Tidy wires away for the spare 2 phases</translate> | ||
| + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0317.JPG | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Add 2 off | + | |Step_Title=<translate>Add 2 off drives to Module C</translate> |
| − | |Step_Content=<translate>May need to move trunking or mount directly to side of enclosure.</translate> | + | |Step_Content=<translate>May need to move trunking or mount directly to side of enclosure. |
| + | |||
| + | |||
| + | Drive can be WEG or EATON</translate> | ||
| + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0321.JPG | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate> | + | |Step_Title=<translate>Remove breaker and contactor from Module E</translate> |
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate> | + | |Step_Title=<translate>Add 10A single pole MCB in Module E</translate> |
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
| + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0322.JPG | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Add 1 Off | + | |Step_Title=<translate>Add 1 Off drive to Module E</translate> |
| − | |Step_Content=<translate></translate> | + | |Step_Content=<translate>May need to move trunking or mount directly to side of enclosure. |
| + | |||
| + | |||
| + | Drive can be WEG or EATON</translate> | ||
| + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_DSC_0326.JPG | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>For each | + | |Step_Title=<translate>For each WEG drive</translate> |
| − | |Step_Content=<translate> | + | |Step_Content=<translate>* Live wire |
| − | + | * Neutral wire | |
| − | * | + | * Earth wire |
| − | *Neutral | + | * 0v supply |
| − | *Earth | + | * FWD and REV Signals |
| − | * | + | * Motor cables wire directly into bottom of the drive |
| − | * | ||
<br /></translate> | <br /></translate> | ||
| − | |Step_Picture_00= | + | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_Module_C_control_wiring_for_Eaton_drives.JPG |
| − | |Step_Picture_00_annotation | + | |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":84,"top":-3,"width":332,"height":363,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.24,"scaleY":1.24,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/e/e1/Fitting_Zx5_Crank_Upgrade_Module_C_control_wiring_for_Eaton_drives.JPG","filters":[]}],"height":450,"width":600} |
| − | + | |Step_Picture_01=Fitting_Zx5_Crank_Upgrade_Module_E_control_wiring_for_Eaton_drive.JPG | |
| − | + | |Step_Picture_01_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":103,"top":0,"width":260,"height":357,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.26,"scaleY":1.26,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/e/eb/Fitting_Zx5_Crank_Upgrade_Module_E_control_wiring_for_Eaton_drive.JPG","filters":[]}],"height":450,"width":600} | |
| − | + | |Step_Picture_02=Fitting_Zx5_Crank_Upgrade_CRANK_D_AND_E.JPG | |
| − | + | |Step_Picture_03=Fitting_Zx5_Crank_Upgrade_CRANK_E.JPG | |
| − | | | ||
| − | | | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| Ligne 204 : | Ligne 214 : | ||
|Step_Content=<translate>Overwrite existing links if any exist | |Step_Content=<translate>Overwrite existing links if any exist | ||
| − | <br /></translate> | + | <br />See the wiring for MC2C and MC2E in Step 22 for the link IORefs and locations</translate> |
|Step_Picture_00=Fitting_Zx5_Crank_Upgrade_Annotation_2019-10-16_141758.jpg | |Step_Picture_00=Fitting_Zx5_Crank_Upgrade_Annotation_2019-10-16_141758.jpg | ||
}} | }} | ||
| Ligne 233 : | Ligne 243 : | ||
|Step_Content=<translate>* Backup Old multi folder | |Step_Content=<translate>* Backup Old multi folder | ||
* Copy in new winMulti version to c:\multi overwriting what is there</translate> | * Copy in new winMulti version to c:\multi overwriting what is there</translate> | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Programme WEG drives</translate> | ||
| + | |Step_Content=<translate>Follow link below for information on programming WEG drives: | ||
| + | |||
| + | |||
| + | [[WEG Inverter Setup]]</translate> | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| Ligne 244 : | Ligne 261 : | ||
*End stops should be set so the rack can never run off the pinion - always a full tooth engaged | *End stops should be set so the rack can never run off the pinion - always a full tooth engaged | ||
*Each crank motion stops when the input is seen, and then decelerates. Therefore, set the crank input position to allow for this deceleration before hitting end stop. Normally about 30mm | *Each crank motion stops when the input is seen, and then decelerates. Therefore, set the crank input position to allow for this deceleration before hitting end stop. Normally about 30mm | ||
| − | *The crank clutches should be set to slip</translate> | + | *The crank clutches should be set to slip before damage is done to the crank end stops in the event that the sensors do not work</translate> |
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version actuelle datée du 18 novembre 2024 à 11:12
Fitting the crank upgrade to Z065, Z066, Z067
Difficulté
Difficile
Durée
2 jour(s)
Sommaire
- 1 Introduction
- 2 Étape 1 -
- 3 Étape 2 - Remove Link arm connecting to rack and pinion
- 4 Étape 3 - Remove pivot shaft and arm
- 5 Étape 4 - Undo clutch and remove Cam
- 6 Étape 5 - Add sprocket to clutch
- 7 Étape 6 - Fix idler plate to upright
- 8 Étape 7 - Fix split sprocket onto drive shaft
- 9 Étape 8 - Drill and pin split sprocket to shaft
- 10 Étape 9 - Add chain minimum length sprocket to sprocket
- 11 Étape 10 - Fit Module C Crank Home sensor plate to Arm 5
- 12 Étape 11 - Fit Module C Crank Out sensor plate to Arm 5
- 13 Étape 12 - Fit Module D Crank Home sensor plate to Arm 5
- 14 Étape 13 - Fit Module D Crank Out sensor plate to Arm 5
- 15 Étape 14 - Fit Module E Crank Out sensor plate to Arm 5
- 16 Étape 15 - Fit Module E Crank Home sensor plate to Arm 5
- 17 Étape 16 - Remove 2 off motor breakers and contactors from Module C
- 18 Étape 17 - Add 2 off 10A single pole MCB's in Module C
- 19 Étape 18 - Add 2 off drives to Module C
- 20 Étape 19 - Remove breaker and contactor from Module E
- 21 Étape 20 - Add 10A single pole MCB in Module E
- 22 Étape 21 - Add 1 Off drive to Module E
- 23 Étape 22 - For each WEG drive
- 24 Étape 23 - Wire Sensor Cables to EtherCAT boxes
- 25 Étape 24 - Latest Front End software installed
- 26 Étape 25 - Map new Links
- 27 Étape 26 - Activate Configuration
- 28 Étape 27 - Add new IO Refs to IODef.mul
- 29 Étape 28 - Latest Front End software installed
- 30 Étape 29 - Programme WEG drives
- 31 Étape 30 - Test Function
- 32 Commentaires
Introduction
This upgrade replaces the crank arm assemblies on Z065, Z066 and Z067 with a direct drive system to improve reliability
This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes
Étape 1 -
IF EATON DRIVES ONLY* Program Drives before they leave
Running frequency
Control mode
Accel time
Decel time
Étape 2 - Remove Link arm connecting to rack and pinion
Étape 3 - Remove pivot shaft and arm
Étape 4 - Undo clutch and remove Cam
Étape 5 - Add sprocket to clutch
B0001166
Étape 6 - Fix idler plate to upright
Étape 7 - Fix split sprocket onto drive shaft
Étape 8 - Drill and pin split sprocket to shaft
Étape 9 - Add chain minimum length sprocket to sprocket
Use idler to create tension
Étape 10 - Fit Module C Crank Home sensor plate to Arm 5
Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes
Étape 11 - Fit Module C Crank Out sensor plate to Arm 5
This one has an extension that may or not be required. See Module D Crank Out Sensor for more info.
Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes
Étape 12 - Fit Module D Crank Home sensor plate to Arm 5
Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes
Étape 13 - Fit Module D Crank Out sensor plate to Arm 5
This one has an extension
Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes
Étape 14 - Fit Module E Crank Out sensor plate to Arm 5
Sensor cables run to rear Module E cabinet - EtherCAT fieldbus boxes
Étape 15 - Fit Module E Crank Home sensor plate to Arm 5
This one has an extension
Sensor cables run to rear Module E cabinet - EtherCAT fieldbus boxes
Étape 16 - Remove 2 off motor breakers and contactors from Module C
Étape 17 - Add 2 off 10A single pole MCB's in Module C
Tidy wires away for the spare 2 phases
Étape 18 - Add 2 off drives to Module C
May need to move trunking or mount directly to side of enclosure.
Drive can be WEG or EATON
Étape 19 - Remove breaker and contactor from Module E
Étape 20 - Add 10A single pole MCB in Module E
Étape 21 - Add 1 Off drive to Module E
May need to move trunking or mount directly to side of enclosure.
Drive can be WEG or EATON
Étape 22 - For each WEG drive
- Live wire
- Neutral wire
- Earth wire
- 0v supply
- FWD and REV Signals
- Motor cables wire directly into bottom of the drive
Étape 23 - Wire Sensor Cables to EtherCAT boxes
Module C and D cranks to back of Module C cabinet
Module E crank to back of Module E cabinet
Étape 24 - Latest Front End software installed
- Backup Old multi folder
- Copy in new winMulti version to c:\multi overwriting what is there
Étape 25 - Map new Links
Overwrite existing links if any exist
See the wiring for MC2C and MC2E in Step 22 for the link IORefs and locations
Étape 26 - Activate Configuration
And restart in run mode when prompted
Étape 27 - Add new IO Refs to IODef.mul
Ask HQ to download a relevant IODef.mul file
OuC_CrankFWD,273,2,0,0,False,False,3,8,-,False,0
OuC_CrankREV,274,2,0,0,False,False,3,9,-,False,0
OuD_CrankFWD,275,2,0,0,False,False,3,10,-,False,0
OuD_CrankREV,276,2,0,0,False,False,3,11,-,False,0
OuE_CrankFWD,277,2,0,0,False,True,64,0,-,False,0
OuE_CrankREV,278,2,0,0,False,True,64,1,-,False,0
And these removed
Étape 28 - Latest Front End software installed
- Backup Old multi folder
- Copy in new winMulti version to c:\multi overwriting what is there
Étape 29 - Programme WEG drives
Follow link below for information on programming WEG drives:
Étape 30 - Test Function
- Ensure all Out and home sensors are working and correctly oriented. Home is towards rear of machine, Fwd or Out is towards front.
- Ensure the clutches are set to slip if the crank bottoms out
- Test direction of all cranks (Fwd is towards front). Switch phases on motors if direction needs to change. The PLC has hard code to switch the outputs off when the sensors are covered
Key Pointers
- End stops should be set so the rack can never run off the pinion - always a full tooth engaged
- Each crank motion stops when the input is seen, and then decelerates. Therefore, set the crank input position to allow for this deceleration before hitting end stop. Normally about 30mm
- The crank clutches should be set to slip before damage is done to the crank end stops in the event that the sensors do not work
Draft
Français
English
Deutsch
Español
Italiano
Português