| [version en cours de rédaction] | [version en cours de rédaction] |
(Page créée avec « {{Tuto Details |Description=<translate>Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during... ») |
|||
| Ligne 1 : | Ligne 1 : | ||
{{Tuto Details | {{Tuto Details | ||
|Description=<translate>Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing.</translate> | |Description=<translate>Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing.</translate> | ||
| + | |Categories=Maintenance | ||
|Difficulty=Medium | |Difficulty=Medium | ||
|Duration=30 | |Duration=30 | ||
| Ligne 7 : | Ligne 8 : | ||
}} | }} | ||
{{Introduction | {{Introduction | ||
| − | |Introduction=<translate>Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing.</translate> | + | |Introduction=<translate>Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing. There are 6 possible states the z block can be in. Each of these can have a different length of protrusion for different profiles. |
| + | |||
| + | |||
| + | 12 x M8 Screws | ||
| + | |||
| + | 12 x M8 Nuts | ||
| + | |||
| + | 12 x wire numbers 1 - 6</translate> | ||
}} | }} | ||
{{Materials}} | {{Materials}} | ||
{{EPI}} | {{EPI}} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate></translate> | ||
| + | |Step_Content=<translate></translate> | ||
| + | |Step_Picture_00=Commissioning_-_Z-Block_Calibration_Z-Transom.png | ||
| + | |Step_Picture_01=Commissioning_-_Z-Block_Calibration_ZBLOCK2.png | ||
| + | |Step_Picture_02=Commissioning_-_Z-Block_Calibration_Zblockbinary.png | ||
| + | }} | ||
{{Tuto Step | {{Tuto Step | ||
|Step_Title=<translate></translate> | |Step_Title=<translate></translate> | ||
| Ligne 17 : | Ligne 32 : | ||
{{Notes}} | {{Notes}} | ||
{{PageLang | {{PageLang | ||
| + | |Language=en | ||
|SourceLanguage=none | |SourceLanguage=none | ||
|IsTranslation=0 | |IsTranslation=0 | ||
| − | |||
}} | }} | ||
{{Tuto Status | {{Tuto Status | ||
|Complete=Draft | |Complete=Draft | ||
}} | }} | ||
Version du 4 octobre 2019 à 13:41
Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing.
Difficulté
Moyen
Durée
30 minute(s)
Introduction
Commonly used during sawing on Z transoms, the Z block operation is used to fasten the profile, making sure it does not move during sawing. There are 6 possible states the z block can be in. Each of these can have a different length of protrusion for different profiles.
12 x M8 Screws
12 x M8 Nuts
12 x wire numbers 1 - 6Étape 1 -
Étape 2 -
Draft
Français
English
Deutsch
Español
Italiano
Português