Autoflow Maintenance - Outfeed Table : Différence entre versions

[version en cours de rédaction]

Version actuelle datée du 8 décembre 2022 à 18:06

Procedures for Daily, Weekly and monthly maintenance on Autoflow Outfeed Table

Auteur Gareth Green | Dernière modification 8/12/2022 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Moyen

Durée

30 minute(s)

Procedures for Daily, Weekly and monthly maintenance on Autoflow Outfeed Table

Difficulté

Moyen

Durée

30 minute(s)

Sommaire

1 Introduction
2 Étape 1 - Eject Bed
3 Étape 2 - Outfeed Pushers and Safety Gate
4 Étape 3 - Conveyor Belt
5 Étape 4 - Extraction System
6 Commentaires

Autoflow, Maintenance, Outfeed Autoflow.jpg.jpg

Introduction

The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention

Étape 1 - Eject Bed

Clean Stainless Steel Bed of swarf and remove any tape that may have transferred onto the bed during normal operation
Lightly oil shaft on underside of bed, lightly oil cylinder rods
Lghtly oil Hepco rail, 1 -2 pumps of grease into Linear Bearings
Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds
Check Hepco rail, Linear Bearings, Shafts and cylinders for damage or wear

Étape 2 - Outfeed Pushers and Safety Gate

Clean area of swarf and Debris
Lightly oil Cylinder Rods, lightly oil Shafts
Check function of gate and Siren via IO Screen
Check Cylinder Rods and Shafts for wear or damage
Check blue bar smooth function via IO screen

Étape 3 - Conveyor Belt

Clean area of swarf and offcuts, empty waste bin as needed
Check belt for signs of wear or cuts in belt

Étape 4 - Extraction System

Check swarf level and change the bag when full
Tap / shake gently the exhaust felt bag to allow the build-up of swarf on the inside of the bag to fall into the clear bag below
Visually check the exhaust felt bags for any signs of damage/holes

Commentaires

en none 0 Draft

@@ Ligne 16 : / Ligne 16 : @@
 {{Tuto Step
 |Step_Title=<translate>Eject Bed</translate>
-|Step_Content=<translate>Daily – clean Stainless Steel Bed of swarf and remove any tape that may have transferred onto the bed during normal operation
+|Step_Content=<translate>* Clean Stainless Steel Bed of swarf and remove any tape that may have transferred onto the bed during normal operation
+* Lightly oil shaft on underside of bed, lightly oil cylinder rods
-Weekly – lightly oil shaft on underside of bed, lightly oil cylinder rod’s, lightly oil Hepco rail, 1 -2 pumps of grease into Linear Bearings, use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds
+* Lghtly oil Hepco rail, 1 -2 pumps of grease into Linear Bearings
+* Use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds
-Monthly – check Hepco rail, Linear Bearings, Shafts and cylinders for damage or wear</translate>
+* Check Hepco rail, Linear Bearings, Shafts and cylinders for damage or wear</translate>
 |Step_Picture_00=Autoflow_Maintenance_-_Infeed_image32.jpeg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1378,"height":1034,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.44,"scaleY":0.44,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/e/eb/Autoflow_Maintenance_-_Infeed_image32.jpeg","filters":[]},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":148.3,"top":120,"width":137.74,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Stainless Bed","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":204,"top":249,"width":100,"height":224,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-50,"x2":50,"y1":-112,"y2":112,"x2a":49.152086252022315,"y2a":90.47603562825867,"x2b":34.54188013302213,"y2b":96.99844907424088},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":154,"top":137,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":254,"top":361,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":302,"top":112,"width":73.36,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Cylinder Rod","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":350,"top":160.5,"width":68,"height":89,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-34,"x2":34,"y1":-44.5,"y2":44.5,"x2a":28.214516317298447,"y2a":23.750827039199997,"x2b":15.500737360250596,"y2b":33.46472556818038},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":316,"top":116,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":384,"top":205,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586}],"height":450,"width":600}
@@ Ligne 28 : / Ligne 28 : @@
 {{Tuto Step
 |Step_Title=<translate>Outfeed Pushers and Safety Gate</translate>
-|Step_Content=<translate>Daily – Clean area of swarf and Debris
+|Step_Content=<translate>* Clean area of swarf and Debris
+* Lightly oil Cylinder Rods, lightly oil Shafts
-Weekly – Lightly oil Cylinder Rods, lightly oil Shafts, gently wipe over with a soft cloth the combined Klaxon and Strobe unit
+* Check function of gate and Siren via IO Screen
+* Check Cylinder Rods and Shafts for wear or damage
-Monthly – Check Cylinder Rods and Shafts for wear or damage, check Blue Bar for damage</translate>
+* Check blue bar smooth function via IO screen</translate>
 |Step_Picture_00=Autoflow_Maintenance_-_Infeed_image34.jpeg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1192,"height":1589,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.5,"scaleY":0.5,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/d/d7/Autoflow_Maintenance_-_Infeed_image34.jpeg","filters":[]},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":186.75,"top":516,"width":202.85,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Safety Gate Cylinder","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":800,"width":600}
@@ Ligne 38 : / Ligne 38 : @@
 {{Tuto Step
 |Step_Title=<translate>Conveyor Belt</translate>
-|Step_Content=<translate>Daily – Clean area of swarf and offcuts, empty waste bin as needed
+|Step_Content=<translate>* Clean area of swarf and offcuts, empty waste bin as needed
+* Check belt for signs of wear or cuts in belt</translate>
-Weekly – Check belt for signs of wear or cuts in belt</translate>
 |Step_Picture_00=Autoflow_Maintenance_-_Infeed_image35.jpeg
 }}
 {{Tuto Step
 |Step_Title=<translate>Extraction System</translate>
-|Step_Content=<translate>Daily – check swarf level periodically throughout the shift and change the bag when full
+|Step_Content=<translate>* Check swarf level and change the bag when full
+* Tap / shake gently the exhaust felt bag to allow the build-up of swarf on the inside of the bag to fall into the clear bag below
-Weekly – with the extraction system switched off tap / shake gently the White needle felt bag to allow the build-up of swarf on the inside of the bag to fall into the clear bag below
+* Visually check the exhaust felt bags for any signs of damage/holes</translate>
-Monthly – visually check the White needle felt bags for any signs of damage/holes</translate>
 |Step_Picture_00=Autoflow_Maintenance_-_Outfeed_Table_Autoflow_Extractor.png
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":749,"height":999,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.8,"scaleY":0.8,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/9/94/Autoflow_Maintenance_-_Outfeed_Table_Autoflow_Extractor.png","filters":[]}],"height":800,"width":600}