| [version en cours de rédaction] | [version en cours de rédaction] |
(Page créée avec « {{Tuto Details |Description=<translate>Procedures for Maintenance of the Autoflow Machining Centre Module</translate> |Categories=Maintenance |Difficulty=Medium |Duration=... ») |
|||
| Ligne 1 : | Ligne 1 : | ||
{{Tuto Details | {{Tuto Details | ||
| + | |Main_Picture=Autoflow.jpg.jpg | ||
| + | |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-55,"top":-35,"width":3508,"height":2481,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.21,"scaleY":0.21,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/5/55/Autoflow.jpg.jpg","filters":[]},{"type":"wfrect","version":"2.4.6","originX":"center","originY":"center","left":317.54,"top":238.73,"width":83.59,"height":196.12,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":0,"ry":0}],"height":450.14866204162536,"width":600} | ||
|Description=<translate>Procedures for Maintenance of the Autoflow Machining Centre Module</translate> | |Description=<translate>Procedures for Maintenance of the Autoflow Machining Centre Module</translate> | ||
|Categories=Maintenance | |Categories=Maintenance | ||
| Ligne 76 : | Ligne 78 : | ||
{{Notes}} | {{Notes}} | ||
{{PageLang | {{PageLang | ||
| + | |Language=en | ||
|SourceLanguage=none | |SourceLanguage=none | ||
|IsTranslation=0 | |IsTranslation=0 | ||
| − | |||
}} | }} | ||
{{Tuto Status | {{Tuto Status | ||
|Complete=Draft | |Complete=Draft | ||
}} | }} | ||
Version du 23 janvier 2020 à 13:55
Procedures for Maintenance of the Autoflow Machining Centre Module
Difficulté
Moyen
Durée
2 heure(s)
Introduction
The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention:
Étape 1 - Infeed Vertical and horizontal rollers
Daily – remove any tape or debris which may have become entangled in the rollers
Weekly – apply oil to top and side of roller units and then slowly spin them for a few revolutions to allow the oil to penetrate the bearings
Étape 2 - Spindle Motors
Daily – Ensure that each spindle will turn freely with no grinding noise when rotating, check cutters for chips or damage, check V – Notch blades for chipped or damaged teeth
Check Spindles slide freely in and out on full range of movement
Monthly - Lubricate slideway bearings
Étape 3 - Slewing Ring and Pinion wheel
Daily – clean area of swarf or debris
Weekly – visually check pinion wheel and slewing ring for any damage, chips or cracks, remove any debris that may have become caught up in the teeth
Étape 4 - Y Axis Rails
4 off Located at the bottom of the machining centre cabinet.
Daily – clean away any debris
Monthly– lightly oil rail surface with supplied oil
Étape 5 - Z Axis Linear Bearings
4 off
Daily – clear area of debris
Monthly– 1 – 2 pumps of grease via grease nipple, wipe away any excess grease
Étape 6 - Auto lube System
Check level of grease in Auto lube
Part replacement order code is M0001047
Draft
Français
English
Deutsch
Español
Italiano
Português