TM018B Microline and ZX3 V Notch Blade Setup

ZX3/Microline/Flowline ZX3 V Notch Blade Setup This module guides the engineer on how to correctly set the V notch blades

Difficulté

Hard Difficile

Durée

30 minute(s) minute(s)

Microline, ZX3, VNotch, Setup, Blade, bladeoffset TM018B_Microline_and_ZX3_V_Notch_Blade_Setup_ZX3_Ring.jpg

Introduction

The engineer will need a reasonable mechanical knowledge, and a working knowledge of the operation of the machine.

You will need callipers (+/-0.05mm) and an accurate rule

The setting of the V notch blades on a ZX3 Ring revolves around the setting of two groups of parameters:

• V and W axis positions
• Blade offsets for each blade

The rough position of V and W axes is set first, then the individual blade offsets are set, and finally a test is run to tweak the accuracy to gain perfection.

There are two “tweaking” parameters for each blade. The two parameters are:

• Depth offset – how deep into the bar
• X axis offset – position of point of blade relative to the spindle centreline

• Pièces et outils

Pièces et outils

150mm Caliper

Digital or Analogue Calipers - Accurate to 0.01mm

150mm Caliper

150mm Rule

150mm Rule

150mm Rule

Étape 1 - Before You Start

1. Make sure the Datum is correct first.
2. V notch blades are not buckled.
3. Check that the profile width is correct for the profile you are testing.

Find out which V Notch files the machine is using by checking the operation setup. A simple way of doing this is shown in the pictures.

Picture 1 - shows this machine uses VF / VR codes

Picture 2 - shows a different machine using VAF3 codes

Note this "mnd type" for later

...The VF... codes are the original method of setting up the machines, the VAF3 codes are seen as an improvement because it makes the naming of the variables for the offsets a little clearer and groups them together. It also improves the machine cycle time by allowing the use of startOffset - the x axis needs to move only once to the start of the V notch

Étape 2 - Run a VTest

A calibration mnd file has been written to help line up the  x offsets called VTEST. This program creates the following pattern on the bottom of the profile using a 10mm spindle and the notching blades themselves:

Run the VTest operation on a length of large outer frame of at least 1m long. Put the    operation at a position of 500mm.

The pattern allows you to measure the offsets required with calipers.

...Profile is viewed from the bottom face, Basically turn it over when it comes of the transfer table.

Étape 3 - Measure Results for x Offsets

1. Measure between the VI blade and the edge of the 10mm slot – This value is the xoffsetVI (and also the xoffsetWI).  (We need to add 5mm to the measured Value).  50.33mm
2. Measure between the VO blade and the edge of the 10mm slot – This value is the xoffsetVO (and also the xoffsetWO).  (We need to add 5mm to the measured Value) 87.59mm

...The 5mm is added becasue this is half the 10mm slot width - thus measuring to the centreline of the slot

Étape 4 - Update the Parameters for xOffsets

1. Set the xOffsetVI and WI to the new value settings. THIS VALUE IS ALWAYS POSITIVE
2. Set the xOffsetVO and WO to the new value in settings. THIS VALUE IS ALWAYS NEGATIVE

Depending on the software version, there are 4 places where these settings are stored / edited

Software Version	MND Type	Parameter location
Multi.exe / DOS	VF / VF	Tooling Setup
winMulti	VF / VR	Tooling Setup
winMulti	VAF3 / WAF3	uservariables.mul
winMulti v5+	VAF3 / WAF3	Settings->Notching

en none 0 Draft