| [version en cours de rédaction] | [version en cours de rédaction] |
(Page créée avec « {{Tuto Details |Description=<translate>Autoflow Mk1 - 3 Daily Mainrtenance Procedures to be carried out by Operators</translate> |Categories=Maintenance |Difficulty=Easy |... ») |
|||
| Ligne 1 : | Ligne 1 : | ||
{{Tuto Details | {{Tuto Details | ||
| + | |Main_Picture=Autoflow_2.jpg | ||
| + | |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-47,"top":-31,"width":3508,"height":2481,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.21,"scaleY":0.21,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/9/9a/Autoflow_2.jpg","filters":[]}],"height":450.14354066985646,"width":600} | ||
|Description=<translate>Autoflow Mk1 - 3 Daily Mainrtenance Procedures to be carried out by Operators</translate> | |Description=<translate>Autoflow Mk1 - 3 Daily Mainrtenance Procedures to be carried out by Operators</translate> | ||
|Categories=Maintenance | |Categories=Maintenance | ||
| Ligne 56 : | Ligne 58 : | ||
{{Notes}} | {{Notes}} | ||
{{PageLang | {{PageLang | ||
| + | |Language=en | ||
|SourceLanguage=none | |SourceLanguage=none | ||
|IsTranslation=0 | |IsTranslation=0 | ||
| − | |||
}} | }} | ||
{{Tuto Status | {{Tuto Status | ||
|Complete=Draft | |Complete=Draft | ||
}} | }} | ||
Version du 8 décembre 2022 à 17:49
Autoflow Mk1 - 3 Daily Mainrtenance Procedures to be carried out by Operators
Difficulté
Facile
Durée
15 minute(s)
Introduction
The following areas should be attended to daily
This routine should take no more than 15 minutesÉtape 1 - Daily Tests
To check the machine is ready for production, a couple of simple tests can be run
- Datum Test
- Pos Test
Étape 2 - Infeed Table
- Thorough blow down of the infeed module
- Blow down of the gripper carriage
- Wipe the offcut measurement sensors
- Remove swarf from grip finger teeth
Étape 3 - Machining Centre Module
- Thorough blow down of the Machining Centre Module
- Visually check tooling for damage or swarf buildup
- Check the V notch blades are not buckled
- Check M/C rollers for tape build up
- Empty M/C waste boxes if required
Étape 4 - Saw Module Cabinet
- Thorough blow down of the saw module
- Remove any loose waste pieces in the saw
- Check the the rear rollers and saw beds for profile tape buildup
- Check saw blade pulley belts (tension/replaced as required)
- Empty saw waste box if required
- Empty extraction waste pieces from cyclone / hopper box
Étape 5 - Saw Outfeed
- Thorough blow down of the saw outfeed
- Thorough shake of the extraction top cloth bags
- Change lower extraction bags as required
Draft
Français
English
Deutsch
Español
Italiano
Português