| [version en cours de rédaction] | [version en cours de rédaction] |
| Ligne 1 : | Ligne 1 : | ||
{{Tuto Details | {{Tuto Details | ||
|Main_Picture=Autoflow.jpg.jpg | |Main_Picture=Autoflow.jpg.jpg | ||
| − | |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":- | + | |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-47,"top":-39,"width":800,"height":566,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.92,"scaleY":0.92,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/thumb/5/55/Autoflow.jpg.jpg/800px-Autoflow.jpg.jpg","filters":[]},{"type":"wfrect","version":"2.4.6","originX":"center","originY":"center","left":455.14,"top":188.67,"width":271.62,"height":182.16,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":0,"ry":0}],"height":448.654037886341,"width":600} |
|Description=<translate>Weekly and Monthly Maintenance Procedures for Autoflow Infeed Table</translate> | |Description=<translate>Weekly and Monthly Maintenance Procedures for Autoflow Infeed Table</translate> | ||
|Categories=Maintenance | |Categories=Maintenance | ||
Version du 23 janvier 2020 à 13:00
Weekly and Monthly Maintenance Procedures for Autoflow Infeed Table
Difficulté
Facile
Durée
30 minute(s)
Introduction
The Machine has many moving parts, all which need regular maintenance. Below outlines what items need particular attention:
Étape 1 - Stainless Steel Bed
Daily – this needs to be kept clear of swarf by using the supplied blower gun on the machine
Weekly – use a suitable foam cleaner for cleaning off the glue and tape residue left by the profile rolling along the beds
Étape 2 - Main display unit (Monitor)
Weekly – clean display with soft cloth to avoid dirt, etc. causing malfunction of the touch screen
Étape 3 - Roller units
Daily – clear all swarf from the roller units
Weekly – apply oil to top and side of roller units and then slowly spin them for a few revolutions to allow the oil to penetrate the bearings
Étape 4 - Drive shafts
Weekly – remove any dirt or old grease
Monthly – 1 – 2 pumps of grease via grease nipple, check for any signs of damage or wear
Étape 5 - Chain drive / clutch
Monthly – wipe off any old chain lube and apply fresh chain lube to chains, check for any signs of damage or wear
Draft
Français
English
Deutsch
Español
Italiano
Português