Fitting Zx5 Crank Upgrade

Fitting the crank upgrade to Z065, Z066, Z067

Difficulté

Hard Difficile

Durée

2 day(s) jour(s)

ZX5, Crank Fitting_Zx5_Crank_Upgrade_DSC_0261.JPG

Introduction

This upgrade replaces the crank arm assemblies on Z065, Z066 and Z067 with a direct drive system to improve reliability

This procedure involves mechanical fitting, electrical wiring and help from a TwinCAT3 competent engineer at HQ for software changes

...The drives must be programmed before parts sent out

Étape 1 - Program Eaton Drives before they leave

Running frequency

Control mode

Accel time

Decel time

https://stuga.dokit.app/wiki/Programming_Eaton_DE_Drive

Étape 2 - Remove Link arm connecting to rack and pinion

Étape 3 - Remove pivot shaft and arm

Étape 4 - Undo clutch and remove Cam

Étape 5 - Add sprocket to clutch

B0001166

Étape 6 - Fix idler plate to upright

Étape 7 - Fix split sprocket onto drive shaft

...Line up with a straight edge

Étape 8 - Drill and pin split sprocket to shaft

Étape 9 - Add chain minimum length sprocket to sprocket

Use idler to create tension

Étape 10 - Fit Module C Crank Home sensor plate to Arm 5

Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes

Étape 11 - Fit Module C Crank Out sensor plate to Arm 5

This one has an extension that may or not be required. See Module D Crank Out Sensor for more info.

Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes

Étape 12 - Fit Module D Crank Home sensor plate to Arm 5

Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes

Étape 13 - Fit Module D Crank Out sensor plate to Arm 5

This one has an extension

Sensor cables run to rear Module C cabinet - EtherCAT fieldbus boxes

Étape 14 - Fit Module E Crank Out sensor plate to Arm 5

Sensor cables run to rear Module E cabinet - EtherCAT fieldbus boxes

Étape 15 - Fit Module E Crank Home sensor plate to Arm 5

This one has an extension

Sensor cables run to rear Module E cabinet - EtherCAT fieldbus boxes

Étape 16 - Remove 2 off breaker and contactor Module C

Étape 17 - Add 2 off single pole breaker Module C

Tidy wires away for the spare 2 phases

Étape 18 - Add 2 off Eaton Drive to Module C

May need to move trunking or mount directly to side of enclosure.

Étape 19 - Add single pole breaker Module E

Étape 20 - Remove breaker and contactor Module E

Étape 21 - Add 1 Off Eaton drive to Module E

Étape 22 - For each Eaton Drive

• 1 phase
• Neutral
• Earth
• Fwd and Reverse signals
• Wire motor cables directly to bottom of drives

Étape 23 - Wire Sensor Cables to EtherCAT boxes

Module C and D cranks to back of Module C cabinet

Module E crank to back of Module E cabinet

Étape 24 - Latest Front End software installed

• Backup Old multi folder
• Copy in new winMulti version to c:\multi overwriting what is there

Étape 25 - Map new Links

Overwrite existing links if any exist

Étape 26 - Activate Configuration

And restart in run mode when prompted

Étape 27 - Add new IO Refs to IODef.mul

Ask HQ to download a relevant IODef.mul file

Failing this, the following IO refs need to be added

OuC_CrankFWD,273,2,0,0,False,False,3,8,-,False,0
OuC_CrankREV,274,2,0,0,False,False,3,9,-,False,0
OuD_CrankFWD,275,2,0,0,False,False,3,10,-,False,0
OuD_CrankREV,276,2,0,0,False,False,3,11,-,False,0
OuE_CrankFWD,277,2,0,0,False,True,64,0,-,False,0
OuE_CrankREV,278,2,0,0,False,True,64,1,-,False,0

And these removed

Étape 28 - Latest Front End software installed

• Backup Old multi folder
• Copy in new winMulti version to c:\multi overwriting what is there

Étape 29 - Test Function

1. Ensure all Out and home sensors are working and correctly oriented. Home is towards rear of machine, Fwd or Out is towards front.
2. Ensure the clutches are set to slip if the crank bottoms out
3. Test direction of all cranks (Fwd is towards front). Switch phases on motors if direction needs to change. The PLC has hard code to switch the outputs off when the sensors are covered

Key Pointers

• End stops should be set so the rack can never run off the pinion - always a full tooth engaged
• Each crank motion stops when the input is seen, and then decelerates. Therefore, set the crank input position to allow for this deceleration before hitting end stop. Normally about 30mm
• The crank clutches should be set to slip

en none 0 Draft