[version en cours de rédaction]

Version actuelle datée du 14 juin 2023 à 13:14

Correct setting and adjustment of the Stuertz Conveyor and Indexing System

Auteur Gareth Green | Dernière modification 14/06/2023 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Correct setting and adjustment of the Stuertz Conveyor and Indexing System

Sommaire

1 Quick Adjustment Guide
2 General Sequence of Operation
3 General Setup Procedure
4 IO on Autoflow Mk4 Infeed Table
- 4.1 Commentaires

Index

Quick Adjustment Guide

Goal is to get the second upstand just beyond the rear fence rollers

The photo shows a situation where the index is just behind the rollers, so would need to move forwards

To adjust the second upstand stop position, undo the index arm locking bolt and rotate it around the shaft.

...The belt indexing length is 200mm, which equates to one revolution of the index arm. Therefore to move 50mm will be 1/4 of a turn

Adjustment Guide
Direction	Photo	Adjustment
Towards Operator
Away from Operator

General Sequence of Operation

On a start signal, release motor mechanical brake, start motor
Wait until INDEX and BRAKE sensors are inactive
Wait for BRAKE sensor active
Decelerate motor
Ensure INDEX sensor is covered
Apply Mechanical Brake

...Indexer works on one revolution of motor / gearbox is exactly one index on the conveyor belt

...The loading table should work if the bar is loaded to the front, back or middle of the conveyor "slot". It is recommended that it is pushed to the rear of the slot, but this will only work if the indexing system is set up properly so that it does not over-rotate and take the bar back past the rollers. In this case, the action of lifting the bar will tip it over

General Setup Procedure

Program the inverter to run forwards and backwards at 50Hz, 0.5s acceleration and deceleration
Use the advance button to move to index one position / index
Check that the INDEX sensor is covered on deceleration - adjust the INDEX on the arc so that this is the case
Measure the position of the index to the backfence - this should be 130mm.
Adjust the position by loosening the Allen key fastening on the INDEX ARM. Rotate up at the rear to move the index closer to the backfence (Arrow shown in blue). Remember, one revolution is one index pulse length (200mm)
Check the sensor spacing vs the slimmest outer frame profile - ensure at leas one sensor is on across slot range in both position 7 and 8

Position of sensors can be adjusted on hole pitch - For 50mm slim outer, the rearmost sensor needs to move forward one pitch

IO on Autoflow Mk4 Infeed Table

Infeed Setup Functionality
IORef	Reference Code	Function	Notes
Y109	OuA_IMotFwd	Rotate Forwards	Forwards means belts should take the profile from the operator towards the backfence
Y110	OuA_IMotRev	Rotate Reverse	Belts rotated in reverse
Y382	OuA_IMotBrake	Motor Brake	Motors have a brake function white needs to be ACTIVE / ON to release the brake
X388	InA_CnvBrk	Sensor to trigger deceleration	This sensor tells the motor when to decelerate to stop the profile close to the loading position. ...Generally, a deceleration on the motor will cause this position to overrun
X033	InA_Index	Sensor to identify that conveyor is in position

en none 0

Commentaires

Draft

@@ Ligne 8 : / Ligne 8 : @@
 <translate>{{#annotatedImageLight:Fichier:Stuertz Conveyor Motor and Indexing Setup Both Sensors.jpg|0=945px|hash=f66005d96f468ba14da74e9a877fe908|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":945,"height":544,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/d/d5/Stuertz_Conveyor_Motor_and_Indexing_Setup_Both_Sensors.jpg","filters":[]},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":238,"top":391,"width":84.46,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"INDEX SENSOR","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":761,"top":88,"width":84.46,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"BRAKE SENSOR","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":120,"top":120,"width":48.93,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":793,"top":375,"width":61.12,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"INDEX ARM","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":651.5,"top":118.5,"width":141,"height":55,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":70.5,"x2":-70.5,"y1":-27.5,"y2":27.5,"x2a":-48.96013525669507,"y2a":27.68500497325538,"x2b":-54.77457727329272,"y2b":12.778889985250494},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":722,"top":91,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":581,"top":146,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":301,"top":337.5,"width":56,"height":77,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-28,"x2":28,"y1":38.5,"y2":-38.5,"x2a":22.706454720924587,"y2a":-17.61990473253586,"x2b":9.76667737207357,"y2b":-27.0306518953366},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":273,"top":376,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":329,"top":299,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":700,"top":380,"width":102,"height":16,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":51,"x2":-51,"y1":-8,"y2":8,"x2a":-30.00186732147378,"y2a":12.80400083420157,"x2b":-32.481351622997174,"y2b":-3.0027115880100474},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":751,"top":372,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":649,"top":388,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":555.5,"top":300,"width":1,"height":116,"fill":"rgba(255,0,0,0)","stroke":"#0054FF","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-0.5,"x2":0.5,"y1":58,"y2":-58,"x2a":8.327295364523408,"y2a":-37.93178016672854,"x2b":-7.672110138290959,"y2b":-38.069706076235555},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":555,"top":358,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":556,"top":242,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586}],"height":544,"width":945}|mediaClass=Image|type=frameless|align=center|src=/images/thumb/d/d5/Stuertz_Conveyor_Motor_and_Indexing_Setup_Both_Sensors.jpg/ia-f66005d96f468ba14da74e9a877fe908-px-Stuertz_Conveyor_Motor_and_Indexing_Setup_Both_Sensors.jpg.png|href=./Fichier:Stuertz Conveyor Motor and Indexing Setup Both Sensors.jpg|resource=./Fichier:Stuertz Conveyor Motor and Indexing Setup Both Sensors.jpg|caption=|size=945px}}
-= Quick Adjustment Guide =
+=Quick Adjustment Guide=
-Goal is to get the second upstand just beyond the rear fence rollers{{#annotatedImageLight:Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|0=400px|hash=dedf65a8e1ff2be3b75298132946d8af|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1119,"height":1020,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.36,"scaleY":0.36,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/a/a4/Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png","filters":[]},{"type":"wfline","version":"2.4.6","originX":"center","originY":"center","left":228.5,"top":170.5,"width":9,"height":319,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":4.5,"x2":-4.5,"y1":-159.5,"y2":159.5},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":233,"top":11,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":224,"top":330,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586}],"height":365,"width":400}|mediaClass=Image|type=frameless|align=center|src=/images/thumb/a/a4/Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png/ia-dedf65a8e1ff2be3b75298132946d8af-px-Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png.png|href=./Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|resource=./Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|caption=|size=400px}}
+Goal is to get the second upstand just beyond the rear fence rollers
+The photo shows a situation where the index is just behind the rollers, so would need to move forwards{{#annotatedImageLight:Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|0=400px|hash=07d0f086697d589a153fc54ad77fd26d|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1119,"height":1020,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.36,"scaleY":0.36,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/a/a4/Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png","filters":[]},{"type":"wfline","version":"2.4.6","originX":"center","originY":"center","left":237.5,"top":159.5,"width":9,"height":319,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":4.5,"x2":-4.5,"y1":-159.5,"y2":159.5},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":242,"top":0,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":233,"top":319,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":213.5,"top":116,"width":45,"height":0,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":22.5,"x2":-22.5,"y1":0,"y2":0,"x2a":-2.5,"y2a":8,"x2b":-2.5,"y2b":-8},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":236,"top":116,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":191,"top":116,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586}],"height":365,"width":400}|mediaClass=Image|type=frameless|alt=Stuertz Conveyor Motor and Indexing Setup upstand position.png|align=center|src=/images/thumb/a/a4/Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png/ia-07d0f086697d589a153fc54ad77fd26d-px-Stuertz_Conveyor_Motor_and_Indexing_Setup_upstand_position.png.png|href=./Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|resource=./Fichier:Stuertz Conveyor Motor and Indexing Setup upstand position.png|caption=|size=400px}}
@@ Ligne 40 : / Ligne 42 : @@
 *Ensure INDEX sensor is covered
 *Apply Mechanical Brake
-{{Info|...Indexer works on one revolution of motor / gearbox is exactly one index on the conveyor belt}}<br />
+{{Info|...Indexer works on one revolution of motor / gearbox is exactly one index on the conveyor belt}}<br />{{Pin|...The loading table should work if the bar is loaded to the front, back or middle of the conveyor "slot". It is recommended that it is pushed to the rear of the slot, but this will only work if the indexing system is set up properly so that it does not over-rotate and take the bar back past the rollers. In this case, the action of lifting the bar will tip it over}}
 =General Setup Procedure=

Stuertz Conveyor Motor and Indexing Setup : Différence entre versions