[version en cours de rédaction]

Version actuelle datée du 15 novembre 2024 à 13:02

How to fit a Yaskawa Inverter as a replacement in the field

Auteur Gareth Green | Dernière modification 15/11/2024 par Stuga Engineer en cours de rédaction ⧼frevu-button-review-label⧽

How to fit a Yaskawa Inverter as a replacement in the field

Yaskawa, Inverter, TB0417

Version History
Version	Date	By	Description	Section	Notes
1	01/01/19	GMG	Original Release
2	23/07/20	GMG	50 / 300Hz Contactors on ZX3 / Microline	2.7	Change text to reflect removal of 50/300Hz contactors and use 50Hz signal for inverter 50Hz signal
3	09/09/20	GMG	V5 software upgrade on E100s	2.6	Add links to the process for installing the latest v5 software
4	22/09/20	GMG	Alternative for InvZro on E100	2.7	Notes on how to use an alternative slice / IO channel for invZro Added a test at the end to check InvZro is functional Add check that the decel time of front end exceeds decel of back end
5	16/10/20	GMG	Anomalies on M008 upgrade	2.71	M008 is a post-refurb Microline with Wago slices and unique slice wiring, not quite the same as a machine wired as E100 from scratch. Modifications noted
6	08/06/22	GMG	Add Autoflow - Delta combination	2.8	A2018 is an autoflow with Twinsafe Fitted and a delta inverter
7	12/10/22	GMG	Y316 InvDP on TwinCAT2	2.1, 2.8	TwinCAT2 uses Y316, not the Standard Y271 as the Inv_DP Output
8	04/01/23	GMG	Add Beckhoff ZX3 Instructions	2.3	Instructions were for ZX4. Now added 50/300Hz Changeover Added Mapping details
9	15/11/24	BCB	Updated for Fault and Alarm output functionality	2.2, 2.3,2.4, 2.6, 2.7, 2.8, 3.1	All machine types can have this update. One parameter change and an additional wire link is required.

1. Introduction-Upgrade Kit

There are two versions of the upgrade kit for these parts:


Stock No	Description	Used On
R0015105	Kit: Yaskawa Inverter Upgrade	All Autoflows ZX3, Zx4, ZX5 from Z043 -in Summary, all machines where inverter is in a seperate cabinet from the front end PC
R0015105B	Kit: Yaskawa Inverter Upgrade - Same Cabinet	All Flowlines (with High speed ring upgrade) ZX3, Zx4 up to Z042 All Microlines - in Summary, all machines where the Inverter is located in the same cabinet as front end PC

1.1 What is the Yaskawa inverter?

Like the Delta inverter, it has an internal PLC. We have worked alongside Goodwin Electronics to write a PLC program specifically for the Stuga machines.
Unlike the Delta inverters, when we receive an inverter from Goodwin Electronics, it will already be pre-programmed and ready to run on any machine.
This inverter can replace the Jaguar and the Delta inverters. It has STO functionality which will be used on new builds and an also be retrospectively wired into machines in the field if needed.
This inverter has shown to provide more protection in fault scenarios than the Delta inverter. One of the worries of the Delta was how it handled issues on the incoming supply. The Yaskawa inverter has shown resilience to shorts, missing phases, phases to earth and other issues on both incoming and outgoing supplies.
The Yaskawa inverter adds extra functionality as well. We can now monitor the zero speed of the spindles. This means we can more accurately time when we switch spindle relays on and off. This will lead to less arcing in spindle boxes and premature failure of spindle cards/relays.

...PLEASE NOTE: BEFORE DISCONNECTING AND RECONNECTING INVERTERS, ENSURE MACHINE IS POWERED DOWN!

1.2 Mechanical Fitting Notes

In place of a Delta inverter

The Yaskawa has a very similar outer body size to the Delta inverter. This means that it will fit into the same space that the Delta did. However, the hole centres are different. New holes will need to be drilled when first fitting a Yaskawa.

In place of a Jaguar inverter

The Yaskawa is much taller than the Jaguar inverter. This may mean that the Yaskawa will not fit in the same space that the Jaguar did. We had the same problem when replacing Jaguar with Delta. There has been occasions in some of the older style ZX cabinets where the plastic trunking had to be re-routed to allow the room for the new inverter to fit.

1.3 Wiring the Yaskawa Inverter

This is a general diagram for cabling into the different machine types - more details for each machine will follow

...The Yaskawa is sometimes supplied with a link wire between SC and SP. This link wire should be removed

When the inverter is fitted, the screen needs to be removed via the clip on the top. If you do not do this, the connector that is behind the screen can be bent out of place and the screen will not reconnect. The main cover that is at the front of the inverter needs to be removed with the screw at the bottom right. You then have to pinch either side of the inverter and lift the cover up.

You can then start wiring in cables from the original inverter setup as per table in the electrical drawing.

There will be some wiring that needs to be added. The table show all extra wiring that is needed for the inverter. The extra wiring will need to splice off existing cables in the electrical cabinet. The Yaskawa inverter needs more IO than the Jaguar. If there is a Delta fitted, you will find that most of the IO will already be in.

1.4 Software Upgrades

Extra Functionality

The Yaskawa inverter has also been programmed to monitor the temperature of the dump resistor. If the machine has a dump resistor with a thermal overload on it, this needs to be wired into the inverter. The alarm for this input is only in fault state when the input is high. This means if you do not have a thermal overload, leave the input terminal empty.

The Yaskawa inverter also has an output to say the spindle is at zero speed. This will need to be wired back into the main machine PLC or IO slices. This will then need a software update from Stuga.

TwinCAT3 Notes

· Timing issues on switching the double plunge configuration means that another IO channel is needed – OuB_InvDP (Y271). This output used to directly control the inverter, not the Y376, Y377, Y58, Y62

· Version 6.2514 or later needed

· Mapping required for Y271

Software Version Requirements
Control System	Front End Version	Back End Version
Nextmove Mint	5.4.4.0 (29/06/16)	3.9997 (Feb 17)
TwinCAT2	5.4.4.0 (29/06/16)	See GG
TwinCAT3	Any	6.2514 (24/10/18)

2. Machine Applications

2.1. Autoflow TwinCAT 2 Notes

Inverter

· Increase C1-01 accel time on 50Hz to 0.4

· Increase C1-05 accel time on 300Hz to 0.4

· Wire S1 to Module B Output Slice channel 1 (Y63)

· Wire S2 to Module B Output Slice channel 2 (Y63)

· Wire S3 and S4 to Module B Output Slice Channel 3 and 4 (Y376)

· 59a to 0v

· 24v link across 3 other inputs

· Inverter fault direct output (bypass the useless link through the overload relay)

· Inverter reset wire to output slice

· Inverter at zero wire to input slice channel 7 (X308)

· Resistor fault not working correctly, leave disconnected STO??! Inverter powers off on estop, works ok, leave links in HC, H1,H2

Back end

· Double link the double plunge outputs (Y316) 0> Channel 3 and 4

...This is different to the standard Y271. Only applies to TwinCAT2 controlled machines

· Link inverter reset (X308) -> Channel 7

· Link inverter zero

· Latest software version

Front end

· Ensure inverter alarm is correct sense

· Parameter Invert300hz=1

· Check inverter display changes to 300hz / 50 HS when spindles are selected

2.2. Flowline Mk3 Refurb TwinCAT3

· The phase monitoring device is not needed any more, but it is inactive, so can be left in place.

· Remove the cable 127 connecting SIG to the Delta inverter

· 3 new wires required, Y63 (Inv_300), Y271(Inv_Dp) and X308 (Inv_Zero)

· Y63, Y271 and X308 will need mapping in TwinCAT3 and adding to IO Ref

· Parameter Invert300Hz needs to be true

· Latest Software needs to be added to sort timings and use of Y63, Y271 and X308

Function	Wire Number / Colour	Yaskawa Terminal
Mains In L1, L2, L3	26, 27,28	L1, L2, L3
Motor Out U, V, W	126, 127, 128	T1, T2, T3
Input: Select 50Hz #1	Y63 Wire to MC4 Ou7	S1
Input: Select 50Hz #2	Link to S1	S2
Input: Double Plunge #1	Y271 Wire To MC4 Ou8	S3
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y358	S5
Input: Inverter Reset	Y374	S6
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8
Inverter OK 24v	24v (Yellow)	MC
Inverter OK Output	X342	M6
Inverter OK Internal Link	0.5mm Blue link between MB and M5	MB and M5
Output 24v Supply	24v (Yellow)	M1, M3
Output: Spindle At Zero	New Wire X308 To io slice MC5 Input channel 8	M2
Output: Motor 2 Safety	Link to S8	M4
STO Override	Link	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	1,2	B1, B2

IODef.mul additions

Inv_Zero,308,1,0,0,0,0,1,12,0
Inv_DP  ,271,2,0,0,0,0,1,10,0
Inv_300 ,63,2,0,0,0,0,1,11,0

2.3. ZX3/4 Mk5/6 (Beckhoff and TwinSAFE) Retrofitting in place of Delta

Electrical Highlights:

Ensure 24v connected to M1, M3 and MC
There is a cable already labelled Y377.
- This will be relabelled Y271 (OuB_InvDp) .
- This connects to S3 and add link to S4.
There is a cable already labelled Y376
- This will be relabelled X308 (InA_InvZero)
- At Yaskawa end, this connects to M2
- At Beckhoff end, this was connected to MC3B pin 15 (OU1). This now needs to be moved to pin 4 (IN4)

...On some machines this cable is in MC3B pin 11

A link wire between M4 and S8 needs to be added
For ZX3 only, there are existing cables Y362 and Y363 (used to signal Delta to change to 50Hz)
- Remove Y363 cable (Only one signal is needed on Yaskawa inverter)
- Rename Y362 cable to Y63 (This is now OuB_300 output to tell Yaskawa to switch to 300Hz)
- At Yaskawa end, Y63 cable connects to S1 with a link to S2
Remove Wire 60B (From Aux contact on F5 to RC1 on Delta Inverter). Not needed because Inverter OK signal does not need to be in series with F5 overload
Remove wire 61B from Phase monitor to Delta MI6. Not needed because Yaskawa does phase monitoring internally
2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram

Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png

Function	Wire Number / Colour	Yaskawa Terminal
Mains In L1, L2, L3	21B, 22B, 23B	L1, L2, L3
Motor Out U, V, W	70B, 71B, 72B	T1, T2, T3
Input: Select 50Hz #1	ZX4: n/c ZX3: Y63	S1
Input: Select 50Hz #2	ZX4: n/c ZX3: Link to S1	S2
Input: Double Plunge #1	Y271 -Wire To MC4 Ou8	S3
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y358	S5
Input: Inverter Reset	Y374	S6
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8
Inverter OK 24v	24v (Yellow)	MC
Inverter OK Output	X342	M6
Inverter OK Internal Link	0.5mm Blue link between MB and M5	Mb and M5
Output 24v Supply	24v (Yellow)	M1, M3
Output: Spindle At Zero	New Wire X308 -To io slice MC3B IN4	M2
Output: Motor 2 Safety	Link to S8	M4
STO Override	Add 2 relays as per diagram. Relay control via Beckhoff safety slices	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	1,2	B1, B2

IODef.mul additions

Inv_Zero,308,1,0,0,0,0,19,5,0
Inv_DP  ,271,2,0,0,0,0,19,6,0
OuB_50 ,63,2,0,0,0,0,19,7,0

Mapping

IO needs to be mapped for the new / remapped IO

X308 Inv_Zero New
Y271 Inv_DP Replacing 377
Y63 OuB_300 in place of 362

2.4. ZX5 Retrofitting in place of Delta

Electrical Highlights:

Ensure 24v connected to M1 and M3
Y271(OuB_InvDp) uses the existing cabling in S4, currently labelled Y377
- A link will need to be added up to S3, where there currently is a cable labelled Y376
Using Y376 cable, remove the labelling and label as X308 (InA_InvZero)
- The other end of this currently goes to the beckhoff slice MC2B pin 15 (OU7). This now needs to be moved to pin 4 (IN4), and relabelled.
A link wire between M4 and S8 needs to be added
2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram

Function	Wire Number / Colour	Yaskawa Terminal
Mains In L1, L2, L3	21B, 22B, 23B	L1, L2, L3
Motor Out U, V, W	70B, 71B, 72B	T1, T2, T3
Input: Select 50Hz #1	n/c	S1
Input: Select 50Hz #2	n/c	S2
Input: Double Plunge #1	Y271 -Wire To MC2B Ou8	S3
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y358	S5
Input: Inverter Reset	Y374	S6
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8
Inverter OK 24v	24v (Yellow)	MC
Inverter OK Output	X342	M6
Inverter OK Internal Link	0.5mm Blue link wire between MB and M5	MB and M5
Output 24v Supply	24v (Yellow)	M1, M3
Output: Spindle At Zero	New Wire X308 -To io slice MC2B IN4	M2
Output: Motor 2 Safety	Link to S8	M4
STO Override	Add 2 relays as per diagram. Relay control via Beckhoff safety slices	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	1,2	B1, B2

IODef.mul additions

Inv_Zero,308,1,0,0,0,0,19,3,0
Inv_DP  ,271,2,0,0,0,0,19,4,0

2.6. Flowline Mk3 Refurb Notes (Nextmove E100)

Electrical Highlights:

To create space for the new inverter, remove the contactor and timer for delaying the drive switching (If they exist) – these are normally located under the old inverter. This switching was only necessary when a DOS PC was used, the contactor can be bypassed.
The supply to the new inverter needs to be wired directly rather than via the estop contactor. The new drive has “STO” (Safe Torque Off) inputs that are wired through two 24v dc relays (supplied). This means when ESTOP is pressed, the drive does not power off, it goes into safe torque off mode. This is a much more reliable system than “crash” shutting off the inverter on estop.
The phase monitoring device (if fitted) is not needed any more, but it is inactive, so can be left in place.
The 50Hz relays for RY1 and RY4 should be removed and the wires RY1, RY4 wired directly to the inverter inputs S1 and S2. This removes the relays as a potential point of failure.
Ensure 24v connected to MC, M1 and M3
New cable for Y271(OuB_InvDp) from S3 and S4 (link), connect to Output channel 8 on 1^st IO slice. Note: the SPDP wire (Y99) may be numbered Y58 and in the output channel 8. For consistency, make:
Ou7 - SPDP – Y99
Ou8 – Inv_DP – Y271
New Cable X308 (InA_InvZero) from M2, connect to Input channel 7 on 4^th IO slice.
A link wire between M4 and S8 needs to be added
2 additional 24v control relays needed for interfacing Estop to the STO inputs as per diagram
The Inverter OK signal (X27) should be wired directly from the inverter to the input slice – it is probably wired via the inverter overload relay auxiliary contact – this is now redundant and will cause confusion
Remove the link SP to SC. This is for grounding an internal PSU that is not used
Remove X99 wire, this was a feedback check to ensure the 50Hz relays had switched, no not required

Function	Wire Number / Colour	Yaskawa Terminal
Mains In L1, L2, L3	26, 27, 28	L1, L2, L3
Motor Out U, V, W	26B, 27B, 28B	T1, T2, T3
Input: Select 50Hz #1	RY1	S1
Input: Select 50Hz #2	RY4	S2
Input: Double Plunge #1	Y271 -Wire To Output channel 8 on 1^st IO slice	S3
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y9	S5
Input: Inverter Reset	Y6	S6
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8
Inverter OK 24v	24v (Yellow)	MC
Inverter OK Output	X27	M6
Inverter OK Internal Link	0.5mm Blue link between MB and M5	MB and M5
Output 24v Supply	24v (Yellow)	M1, M3
Output: Spindle At Zero	New Wire X308 - connect to Input channel 7 on 4^th IO slice.	M2
Output: Motor 2 Safety	Link to S8	M4
STO Override	Add 2 relays as per diagram.	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	1,2	B1, B2

IODef.mul additions

INVDP   ,616,2,8,7,0,0,1,7,1
InZRO   ,608,1,8,14,0,0,2,11,1

Ensure SPDP is:    
SPDP   ,569,2,8,6,0,0,1,6,V

Delete any reference to IS300 input

Alarms.mul

Ensure the alarms are set for each individual spindle:

41,MOVL,False,SPIN1,True,0,4,Spindle 1 Alarm,True,False
42,MOVL,False,SPIN2,True,0,4,Spindle 2 Alarm,True,False
43,MOVL,False,SPIN3,True,0,4,Spindle 3 Alarm,True,False
44,MOVL,False,SPIN4,True,0,4,Spindle 4 Alarm,True,False
45,MOVL,False,SPIN5,True,0,4,Spindle 5 Alarm,True,False
46,MOVL,False,SPIN6,True,0,4,Spindle 6 Alarm,True,False

The MOVL should be High when the inverter is OK.

Remove any alarms relating to IS300 input

Front end

Update software to latest version 5 - see Upgrading to Version 5
Ensure inverter alarm is correct sense (High when inverter OK)
Parameter Invert300hz=1
Parameter InverterOKHigh=1
Parameter psInvDecel300Hz=400
Check inverter display changes to 300hz / 50 HS when spindles are selected

Other software

Download and install Yaskawa DriveWizard

Ensure the Yaskawa USB is connected to the PC

Find the COM port it is connected to (use Device Manager Ports) – this is usually COM3. If there are other connections on the same COM port, right click and uninstall them (EDG). This will need a reboot after uninstalling

Using DriveWizard, or via the physical keypad on the device, change the following parameters

No	Description	New Value
C1-01	50Hz Accel Time	0.4
C1-02	50Hz Decel Time	0.2
C1-05	300Hz Accel Time	0.4
C1-06	300Hz Decel Time	0.2
H2-03	!Alarm	110

2.7. ZX4/ZX3/Microline Replace VXR Notes (Nextmove E100)

Electrical Highlights:

The inverter will need to be located on the side of the cabinet, as the Yaskawa is taller than the VXR
The supply to the new inverter needs to be wired directly rather than via the estop contactor. The new drive has “STO” (Safe Torque Off) inputs that are wired through two 24v dc relays (supplied). This means when ESTOP is pressed, the drive does not power off, it goes into safe torque off mode. This is a much more reliable system than “crash” shutting off the inverter on estop.
The phase monitoring device (if fitted) is not needed any more, but it is inactive, so can be left in place.
Ensure 24v connected to MC, M1 and M3
The Zx3 and Microline have a set of switchover contactors to select 50Hz (Mains) or 300Hz (Inverter). These need to be removed as the Yaskawa will do the switching. The Y5 Hz50 Output will be used to do this on S1 and S2

New cable for Y271 (InvDp) from S3 and S4 (link), connect Output channel 5 on 2nd Output slice (labelled 5)

New Cable X308 (InA_InvZero) from M2, connect to input channel 8 on 1st IO slice (labelled 8).

...If the wires cannot be added as per above diagram, You can wire to any spare channel, however you must change the ioDef file accordingly to remap the input (ASK FOR HELP!)

A link wire between M4 and S8 needs to be added
2 additional 24v control relays needed for interfacing Estop to the STO inputs as per diagram

Fitting Yaskawa Inverter Yaskawa STO Wiring ZX.png

The Inverter OK signal (X48) should be wired directly from the inverter to the input slice – it is probably wired via the inverter overload relay auxiliary contact – this is now redundant and will cause confusion
Remove the link SP to SC. This is for grounding an internal PSU that is not used
Inverter Reset function is done with Y34 SRST. The VXR inverter was powered off on estop, so did not need a reset function. Tag in to a Y34 cable on any servo drive (PL4 pin 2)

Function	Wire Number / Colour	Yaskawa Terminal
Mains In L1, L2, L3	60, 61, 62	L1, L2, L3
Motor Out U, V, W	53, 54, 55	T1, T2, T3
Input: Select 50Hz #1	Y5 (Hz50)	S1
Input: Select 50Hz #2	Y5 (Hz50)	S2
Input: Double Plunge #1	Y271 -Wire To Output channel 5 on 2nd Output slice (labelled 3)	S3
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y31 – extend to run directly Remove the relay R58 and wires 51, 52	S5
Input: Inverter Reset	Y34 – Splice into servo reset – loops across each of the servo drives	S6
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8
Inverter OK 24v	24v (Yellow)	MC
Inverter OK Output	X48 Remove wire 30A	M6
Inverter OK Internal Link	0.5mm Blue Link between MB and M5	M5 and MB
Output 24v Supply	24v (Yellow)	M1, M3
Output: Spindle At Zero	New Wire X308 - connect to Input channel 8 on 1st IO slice (labelled 8).	M2
Output: Motor 2 Safety	Link to S8	M4
STO Override	Add 2 relays as per diagram.	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	Br+, Br-	B1, B2

Fitting Yaskawa Inverter Yaskawa Wiring Photo 1.jpg

Fitting Yaskawa Inverter Yaskawa Wiring Photo 2.jpg

IODef.mul additions

INVDP,616,2,8,12,0,0,18,1,1
InZRO,608,1,8,7,0,0,18,2,1

Edit the Column and row values for the following iodefs to put the all the spindle control on the spindle IO screen – makes testing much easier (items 8 and 9 in the csv) 

INVOK,542,1,8,23,0,0,18,6,0  
HZ50,578,2,0,4,0,0,18,7,D
HZ300,579,2,0,5,0,0,18,8,E
SMOT,558,2,8,15,0,1,18,3,Z
SRST,574,2,8,18,0,0,18,4,F

****** GLENN NOTE ******* On a Microline, check in IODef.mul for

CLSIP,607,2,9,3,0,0,2,3,X
CLSOV,608,2,9,4,0,0,2,4,Y
CLSOP,609,2,9,5,0,0,2,5,Z

change CLSOV from reference 608 to 618

See Microline Issue Saw Outfeed Clamp

Alarms.mul

Ensure the alarms are set for each individual spindle:

41,INVOK,False,SPIN1,True,0,4,Spindle 1 Alarm,True,False
42,INVOK,False,SPIN2,True,0,4,Spindle 2 Alarm,True,False
43,INVOK,False,SPIN3,True,0,4,Spindle 3 Alarm,True,False
44,INVOK,False,SPIN4,True,0,4,Spindle 4 Alarm,True,False
45,INVOK,False,SPIN5,True,0,4,Spindle 5 Alarm,True,False
46,INVOK,False,SPIN6,True,0,4,Spindle 6 Alarm,True,False
47,INVOK,False,SPIN7,True,0,4,Spindle 7 Alarm,True,False

The INVOK should be High when the inverter is OK.

Remove any alarms relating to IS300 input

Front end

Parameter Invert300hz=1
Parameter InverterOKHigh=1
Parameter psInvDecel300Hz=400
Check inverter display is 300hz

Other software

Download and install Yaskawa DriveWizard

Ensure the Yaskawa USB is connected to the PC

Find the COM port it is connected to (use Device Manager Ports) – this is usually COM3. If there are other connections on the same COM port, right click and uninstall them (EDG). This will need a reboot after uninstalling

Using DriveWizard, or via the physical keypad on the device, change the following parameters

No	Description	New Value
C1-01	50Hz Accel Time	0.4
C1-02	50Hz Decel Time	0.2
C1-05	300Hz Accel Time	0.4
C1-06	300Hz Decel Time	0.2
H2-03	!Alarm	110

2.7.1 Anomalies with M008 Upgrade

When upgrading M008, the wiring did not match the expectations above. These anomalies are noted here for guidance on a similar upgrade in future


		Details	Solution
1	Hz50 / Hz300 Outputs	The wiring diagram only shows a Hz300 output on Y6, but the backend software needs Y5 Hz50 to do the switching. Y5 is the main saw motor!	Swap the mapping channel of the Hz50 and Hz300 outputs to ensure Hz50 is connected to the inverter S1, S2 using Y6 (DOUT5) HZ300,579,2,0,9,0,0,18,8,F HZ50,578,2,0,5,0,1,18,7,J
2	Reset	Inverter reset on the drawings is not connected, yet physically connected via the servo cards to Y43, not Y34
3	Nodes	The system uses Beckhoff IO slices, not Wago, therefore needs two sets of nodes. This is a different diagram to the one published. Pictures are below	Different IoDef mapping needed INVDP,616,2,9,13,0,0,18,1,1 InZRO,608,1,8,15,0,0,18,2,1
4	InvOK	Labelled X14 on the drawing and physically in the machine, wired through the overload relay	Wire directly from DIN13 on nextmove - keep same mapping to channel 0,13

2.8 Autoflow with Delta Inverter

Function	Wire Number / Colour	Yaskawa Terminal	Notes
Mains In L1, L2, L3	21B, 22B, 23B	L1, L2, L3
Motor Out U, V, W	29B, 30B, 31B	T1, T2, T3	Ther emay be a phase detection relay between 26B-29B 27B-30B 28B-31B This can be discarded Remove wire 61B from Phase monitor to Delta MI6. Not needed because Yaskawa does phase monitoring internally
Input: Select 50Hz #1	Y63	S1	Existing Y63 OuB_Spin300 connects to S1 and add link to S2
Input: Select 50Hz #2	link to S1	S2	Existing Y63 OuB_Spin300 connects to S1 and add link to S2
Input: Double Plunge #1	Y316 -Wired To MC2B OU1 (pin9)	S3	There is a cable already labelled Y55. This will be relabelled Y316 (OuB_InvDp) . This connects to S3 and add link to S4. ...This is different to the standard Y271. Only applies to TwinCAT2 controlled machines
Input: Double Plunge #2	Link to S3	S4
Input: Motor Run	Y62	S5	Existing wire
Input: Inverter Reset	Y374	S6	Existing Wire
Input: Resistor Thermal Ovl	n/c	S7
Input: Motor 2 Safety	Link to M4	S8	A link wire between M4 and S8 needs to be added
Inverter OK 24v	24v (Yellow)	MC	Ensure 24v connected to MC, not through an auxilliary contact Remove Wire 60B (From Aux contact on F5 to RC1 on Delta Inverter). Not needed because Inverter OK signal does not need to be in series with F5 overload
Inverter OK Output	X90	M6	Ensure this connected directly to MC2B Pin 3 and does not go through any auxilliary
Output 24v Supply	24v (Yellow)	M1, M3	Ensure 24v connected to M1, M3
Output: Spindle At Zero	X308 -To io slice MC2B IN6 (pin6)	M2	Reuse an existing cable for this new connection There is a cable already labelled Y59 This will be relabelled X308 (InA_InvZero) At Yaskawa end, this connects to M2 At Beckhoff end, this was connected to MC2B pin 15 (OU1). This now needs to be moved to pin 6 (IN4)
Output: Motor 2 Safety	Link to S8	M4	A link wire between M4 and S8 needs to be added
InvOK Internal Link	0.5mm Blue Link between MB and M5	M5 and MB
STO Override	Add 2 relays as per diagram. Relay control via Beckhoff safety slices	H1, H2, HC
External 0v	0v (White)	SC
Braking Resistor	1,2	B1, B2	Replace braking resistor if supplied. If not supplied, check the resistor is not short cuircuit - this has been the root casue of failure in the past

IODef.mul additions

InB_InvZero,308,1,0,0,0,0,19,7,0
OuB_InvDP,271,2,0,0,0,0,19,8,0

Alarms.mul additions / changes

41,InB_InvSpinOk,False,OuB_Spin1On,True,0,4,Spindle 1 Alarm,True,False
42,InB_InvSpinOk,False,OuB_Spin2On,True,0,4,Spindle 2 Alarm,True,False
43,InB_InvSpinOk,False,OuB_Spin3On,True,0,4,Spindle 3 Alarm,False,False
44,InB_InvSpinOk,False,OuB_Spin4On,True,0,4,Spindle 4 Alarm,True,False
45,InB_InvSpinOk,False,OuB_Spin5On,True,0,4,Spindle 5 Alarm,True,False
46,InB_InvSpinOk,False,OuB_Spin6On,True,0,4,Spindle 6 Alarm,True,False
47,InB_InvSpinOk,False,OuB_Spin7On,True,0,4,Spindle 7 Alarm,False,False
48,InB_InvSpinOk,False,OuB_Spin8On,True,0,4,Spindle 8 Alarm,True,False
50,InF_GtOpen,0,OuF_Gate,True,30,3,Safety Gate Not Open,False,False,0
51,InF_GtClosed,0,OuF_Gate,False,30,3,Safety Gate Not Closed,False,False,0

Change IO Links in Beckhoff Software
Module	Slice	IO Channel	Was	Change To	Notes
Module B	MC2B	Output 0	Y55	Y271	Were duplicates of the Double plunge output for spindles 2+5. Now change to Ou_InvDP This needs to be a seperate output from the spindle DP becasue the timing is different and crucial
Module B	MC2B	Output 1	Y59	Blank
Module B	MC2B	Input 6	Blank	X308	New input for Inverter at Zero

3. Completion

3.1. Checklist

General Item Checklist before power on
Item	Tick
Inverter Replaced
If the old braking resistor is reused, test the resistance matches the stated value. If an ohmmeter is not available, ensure it is not a dead short to ground or open circuit
Phase Detect Relay Removed
M4 to S8 Link
Inverter OK signal bypasses overload relay and configured so InvOK signal is High when OK
Inverter FWD signal wired in
Inverter 50Hz select wired in and link
Inverter Double Plunge Input and link wired in
Inverter Reset Input Wired In
Inverter At Zero Output wired back to controller
STO Relays Fitted and wired
Mains Connections and Earth Safely wired
Front End updated if required
Back End updated if required ...If this is a Nexmove, set the YASKAWAINVERTER parameter to _TRUE
IO Def reconfigured
Alarms Reconfigured
Yaskawa Drive Wizard installed Download here
Check Inverter accel and decel parameters - Double check that psInvDecel300Hz=400 Inverter Deceleration Parameters C1-02, C1-06 are set to 0.2 Inverter Acceleration Parameters C1-01, C1-05 are set to 0.4 ...the ps is set in milliseconds, the inverter parameter in seconds The inverter deceleration time must be LESS than the front end parameter, otherwise the relay contacts will open before the inverter has finished decelerating the spindles, leading to burning and arcing
Check Inverter DC Injection parameters set to zero Parameters B2 -02 and B2-04
Check parameter H2-03 is set to 110
Test InverterOK signal (high when OK) Ensure alarm triggers on InvOK low
Ov connected to SC
24v Connected to M1, M3, MC
Update Control Systems Log for the software version and Inverter type

3.2. Testing

For this machine type, testing a spindle should follow this process

50Hz V notch motor

1. Select a spindle 1 or 2

2. Set HZ50 to run

3. Set Hz50 off

Single 300Hz Elte Motor

1. Select a spindle 3 to 7

2. Set HZ300

3. Set SMOT to accellerate

4. Ensure InZRO goes off and InvOK stays on

5. Reset SMOT to decelerate

6. Reset HZ300

7. Reset Spindle

Double 300Hz Elte Motor

Same as single, but select double plunge spindles and set InvDP to tell inverter to double the output power

Test InvZro input to system is low when inverter running, high when spindle stops en none 0

Commentaires

Draft

@@ Ligne 6 : / Ligne 6 : @@
 |Tags=Yaskawa, Inverter, TB0417
 }}
-<translate>=What is the Yaskawa inverter?=
+<translate><br />
+{| class="wikitable"
+|+Version History
+!Version
+!Date
+!By
+!Description
+!Section
+!Notes
+|-
+|1
+|01/01/19
+|GMG
+|Original Release
+|
+|
+|-
+|2
+|23/07/20
+|GMG
+|50 / 300Hz Contactors on ZX3 / Microline
+|2.7
+|Change text to reflect removal of 50/300Hz contactors and use 50Hz signal for inverter 50Hz signal
+|-
+|3
+|09/09/20
+|GMG
+|V5 software upgrade on E100s
+|2.6
+|Add links to the process for installing the latest v5 software
+|-
+|4
+|22/09/20
+|GMG
+|Alternative for InvZro on E100
+|2.7
+|Notes on how to use an alternative slice / IO channel for invZro
+Added a test at the end to check InvZro is functional
+Add check that the decel time of front end exceeds decel of back end
+|-
+|5
+|16/10/20
+|GMG
+|Anomalies on M008 upgrade
+|2.71
+|M008 is a post-refurb Microline with Wago slices and unique slice wiring, not quite the same as a machine wired as E100 from scratch. Modifications noted
+|-
+|6
+|08/06/22
+|GMG
+|Add Autoflow  - Delta combination
+|2.8
+|A2018 is an autoflow with Twinsafe Fitted and a delta inverter
+|-
+|7
+|12/10/22
+|GMG
+|Y316 InvDP on TwinCAT2
+|2.1, 2.8
+|TwinCAT2 uses Y316, not the Standard Y271 as the Inv_DP Output
+|-
+|8
+|04/01/23
+|GMG
+|Add Beckhoff ZX3 Instructions
+|2.3
+|Instructions were for ZX4. Now added 50/300Hz Changeover
+Added Mapping details
+|-
+|9
+|15/11/24
+|BCB
+|Updated for Fault and Alarm output functionality
+|2.2, 2.3,2.4, 2.6, 2.7, 2.8, 3.1
+|All machine types can have this update. One parameter change and an additional wire link is required.
+|}
+=1. Introduction-Upgrade Kit=
+There are two versions of the upgrade kit for these parts:
+{| class="wikitable"
+|+
+!Stock No
+!Description
+!Used On
+|-
+|R0015105
+|Kit: Yaskawa Inverter Upgrade
+|All Autoflows
+ZX3, Zx4, ZX5 from Z043
+-in Summary, all machines where inverter is in a seperate cabinet from the front end PC
+|-
+|R0015105B
+|Kit: Yaskawa Inverter Upgrade - Same Cabinet
+|All Flowlines (with High speed ring upgrade)
+ZX3, Zx4 up to Z042
+All Microlines
+- in Summary, all machines where the Inverter is located in the same cabinet as front end PC
+|}
+<br />
+=1.1 What is the Yaskawa inverter?=
 *Like the Delta inverter, it has an internal PLC. We have worked alongside Goodwin Electronics to write a PLC program specifically for the Stuga machines.
@@ Ligne 12 : / Ligne 117 : @@
 *This inverter can replace the Jaguar and the Delta inverters. It has STO functionality which will be used on new builds and an also be retrospectively wired into machines in the field if needed.
 *This inverter has shown to provide more protection in fault scenarios than the Delta inverter. One of the worries of the Delta was how it handled issues on the incoming supply. The Yaskawa inverter has shown resilience to shorts, missing phases, phases to earth and other issues on both incoming and outgoing supplies.
-*The Yaskawa inverter adds extra functionality as well. We can now monitor the zero speed of the spindles. This means we can more accurately time when we switch spindle relays on and off. This will hopefully cause less arcing in spindle boxes and premature failure of spindle cards/relays.
+*The Yaskawa inverter adds extra functionality as well. We can now monitor the zero speed of the spindles. This means we can more accurately time when we switch spindle relays on and off. This will lead to less arcing in spindle boxes and premature failure of spindle cards/relays.
 {{Warning|...PLEASE NOTE: BEFORE DISCONNECTING AND RECONNECTING INVERTERS, ENSURE MACHINE IS POWERED DOWN!}}
-=Mechanical Fitting Notes=
+==1.2 Mechanical Fitting Notes==
-===Fitting the Yaskawa inverter in place of a Delta inverter===
+===In place of a Delta inverter===
 The Yaskawa has a very similar outer body size to the Delta inverter. This means that it will fit into the same space that the Delta did. However, the hole centres are different. New holes will need to be drilled when first fitting a Yaskawa.
-===Fitting the Yaskawa inverter in place of a Jaguar inverter===
+===In place of a Jaguar inverter===
 The Yaskawa is much taller than the Jaguar inverter. This may mean that the Yaskawa will not fit in the same space that the Jaguar did. We had the same problem when replacing Jaguar with Delta. There has been occasions in some of the older style ZX cabinets where the plastic trunking had to be re-routed to allow the room for the new inverter to fit.
-=Wiring the Yaskawa Inverter=
+==1.3 Wiring the Yaskawa Inverter==
 This is a general diagram for cabling into the different machine types - more details for each machine will follow
-<br />{{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa General Wiring.jpg|0=1094px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/d/d6/Fitting_Yaskawa_Inverter_Yaskawa_General_Wiring.jpg|href=./Fichier:Fitting Yaskawa Inverter Yaskawa General Wiring.jpg|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa General Wiring.jpg|caption=|size=1094px}}
+{{Warning|...The Yaskawa is sometimes supplied with a link wire between SC and SP. This link wire should be removed}}
 When the inverter is fitted, the screen needs to be removed via the clip on the top. If you do not do this, the connector that is behind the screen can be bent out of place and the screen will not reconnect. The main cover that is at the front of the inverter needs to be removed with the screw at the bottom right. You then have to pinch either side of the inverter and lift the cover up.
@@ Ligne 34 : / Ligne 139 : @@
 There will be some wiring that needs to be added. The table show all extra wiring that is needed for the inverter. The extra wiring will need to splice off existing cables in the electrical cabinet. The Yaskawa inverter needs more IO than the Jaguar. If there is a Delta fitted, you will find that most of the IO will already be in.
-=Software Upgrades=
+==1.4 Software Upgrades==
 ===Extra Functionality===
@@ Ligne 57 : / Ligne 162 : @@
 |Nextmove Mint
 |5.4.4.0 (29/06/16)
-|3.9997 (Feb 17)
+|3.9997 (Feb 17){{#annotatedImageLight:Fichier:YASKAWAINVERTER parameter.png|0=200px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/b/b2/YASKAWAINVERTER_parameter.png|href=./Fichier:YASKAWAINVERTER parameter.png|resource=./Fichier:YASKAWAINVERTER parameter.png|caption=|size=200px}}<br />
 |-
 |TwinCAT2
@@ Ligne 68 : / Ligne 173 : @@
 |}
 <br />
-=Machine Applications=
+=2. Machine Applications=
-==Autoflow TwinCAT 2 Notes==
+==2.1. Autoflow TwinCAT 2 Notes==
 ====Inverter====
-·        Increase C1-01 accel time on 50Hz to 0.3
+·        Increase C1-01 accel time on 50Hz to 0.4
-·        Increase C1-05 accel time on 300Hz to 0.3
+·        Increase C1-05 accel time on 300Hz to 0.4
 ·        Wire S1 to Module B Output Slice channel 1 (Y63)
@@ Ligne 95 : / Ligne 200 : @@
 ====Back end====
-·        Double link the double plunge outputs (Y271) 0> Channel 3 and 4
+·        Double link the double plunge outputs (Y316) 0> Channel 3 and 4
+{{Info|...This is different to the standard Y271. Only applies to TwinCAT2 controlled machines}}
 ·        Link inverter reset (X308) -> Channel 7
@@ Ligne 110 : / Ligne 218 : @@
 ·        Check inverter display changes to 300hz / 50 HS when spindles are selected
-===Flowline Mk3 Refurb TwinCAT3===
+==2.2. Flowline Mk3 Refurb TwinCAT3==
 ·        The phase monitoring device is not needed any more, but it is inactive, so can be left in place.
@@ Ligne 177 : / Ligne 285 : @@
 | width="170" valign="top" |'''Inverter OK Output'''
 | width="132" valign="top" |X342
-| width="227" valign="top" |MB
+| width="227" valign="top" |M6
+|-
+|'''Inverter OK Internal Link'''
+|0.5mm Blue link between MB and M5
+|MB and M5
 |-
 | width="170" valign="top" |'''Output 24v  Supply'''
@@ Ligne 215 : / Ligne 327 : @@
 </syntaxhighlight><br />
-===ZX4 Mk5/6 (Beckhoff) Retrofitting in place of Delta===
+==2.3. ZX3/4 Mk5/6 (Beckhoff and TwinSAFE) Retrofitting in place of Delta==
 Electrical Highlights:
-·        Ensure 24v connected to M1 and M3
+*Ensure 24v connected to M1, M3 and MC
+*There is a cable already labelled Y377.
+**This will be relabelled Y271 (OuB_InvDp) .
+**This connects to S3 and add link to S4.
+*There is a cable already labelled Y376
+**This will be relabelled X308 (InA_InvZero)
+**At Yaskawa end, this connects to M2
+**At Beckhoff end, this was connected to MC3B pin 15 (OU1). This now needs to be moved to pin 4 (IN4) {{Info|...On some machines this cable is in MC3B pin 11}}<br />
-·        Y271(OuB_InvDp) uses the existing cabling in S4, currently labelled Y377
+*A link wire between M4 and S8 needs to be added
+*<u>For ZX3 only</u>, there are existing cables Y362 and Y363 (used to signal Delta to change to 50Hz)
-o   A link will need to be added up to S3, where there currently is a cable labelled Y376
+**Remove Y363 cable (Only one signal is needed on Yaskawa inverter)
+**Rename Y362 cable to Y63 (This is now OuB_300 output to tell Yaskawa to switch to 300Hz)
-·        Using Y376 cable, remove the labelling and label as X308 (InA_InvZero)
+**At Yaskawa end, Y63 cable connects to S1 with a link to S2
+*Remove Wire 60B (From Aux contact on F5 to RC1 on Delta Inverter). Not needed because Inverter OK signal does not need to be in series with F5 overload
-o   The other end of this currently goes to the beckhoff slice MC3B pin 15 (OU1). This now needs to be moved to pin 4 (IN4), and relabelled.
+*Remove wire 61B from Phase monitor to Delta MI6. Not needed because Yaskawa does phase monitoring internally
+*2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram
-·        A link wire between M4 and S8 needs to be added
+{{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|0=271px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/4/42/Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png|href=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|caption=|size=271px}}<br />
-·        Remove Wire 60B (From Aux contact on F5 to RC1 on Delta Inverter). Not needed because Inverter OK signal does not need to be in series with F5 overload
-·        Remove wire 61B from Phase monitor to Delta MI6. Not needed because Yaskawa does phase monitoring internally
-·        2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram{{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|0=271px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/4/42/Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png|href=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|caption=|size=271px}}<br />
 {| class="wikitable" border="1" cellspacing="0" cellpadding="0"
 | width="170" valign="top" |'''Function'''
@@ Ligne 249 : / Ligne 362 : @@
 |-
 | width="170" valign="top" |'''Input: Select 50Hz #1'''
-| width="227" valign="top" |n/c
+| width="227" valign="top" |ZX4: n/c
+ZX3: Y63
 | width="132" valign="top" |S1
 |-
 | width="170" valign="top" |'''Input: Select 50Hz #2'''
-| width="227" valign="top" |n/c
+| width="227" valign="top" |ZX4: n/c
+ZX3: Link to S1
 | width="132" valign="top" |S2
 |-
@@ Ligne 286 : / Ligne 401 : @@
 | width="170" valign="top" |'''Inverter OK Output'''
 | width="227" valign="top" |X342
-| width="132" valign="top" |MB
+| width="132" valign="top" |M6
+|-
+|'''Inverter OK Internal Link'''
+|0.5mm Blue link between MB and M5
+|Mb and M5
 |-
 | width="170" valign="top" |'''Output 24v Supply'''
@@ Ligne 319 : / Ligne 438 : @@
 Inv_Zero,308,1,0,0,0,0,19,5,0
 Inv_DP  ,271,2,0,0,0,0,19,6,0
-</syntaxhighlight><br />
+OuB_50 ,63,2,0,0,0,0,19,7,0
+</syntaxhighlight>
+====Mapping====
+IO needs to be mapped for the new / remapped IO
+*X308 Inv_Zero New
+*Y271 Inv_DP Replacing 377
+*Y63 OuB_300 in place of 362
+<br />
-===ZX5 Retrofitting in place of Delta===
+==2.4. ZX5 Retrofitting in place of Delta==
 Electrical Highlights:
-* Ensure 24v connected to M1 and M3
+*Ensure 24v connected to M1 and M3
-* Y271(OuB_InvDp) uses the existing cabling in S4, currently labelled Y377
+*Y271(OuB_InvDp) uses the existing cabling in S4, currently labelled Y377
-** A link will need to be added up to S3, where there currently is a cable labelled Y376
+**A link will need to be added up to S3, where there currently is a cable labelled Y376
-* Using Y376 cable, remove the labelling and label as X308 (InA_InvZero)
+*Using Y376 cable, remove the labelling and label as X308 (InA_InvZero)
-** The other end of this currently goes to the beckhoff slice MC2B pin 15 (OU7). This now needs to be moved to pin 4 (IN4), and relabelled.
+**The other end of this currently goes to the beckhoff slice MC2B pin 15 (OU7). This now needs to be moved to pin 4 (IN4), and relabelled.
-* A link wire between M4 and S8 needs to be added
+*A link wire between M4 and S8 needs to be added
-* 2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram
+*2 additional 24v control relays needed for interfacing TwinSafe to the STO inputs as per diagram
 {{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|0=271px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/4/42/Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png|href=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|caption=|size=271px}}<br />
 {| class="wikitable" border="1" cellspacing="0" cellpadding="0"
@@ Ligne 383 : / Ligne 512 : @@
 | width="170" valign="top" |'''Inverter OK Output'''
 | width="227" valign="top" |X342
-| width="132" valign="top" |MB
+| width="132" valign="top" |M6
+|-
+|'''Inverter OK Internal Link'''
+|0.5mm Blue link wire between MB and M5
+|MB and M5
 |-
 | width="170" valign="top" |'''Output  24v Supply'''
@@ Ligne 416 : / Ligne 549 : @@
 Inv_Zero,308,1,0,0,0,0,19,3,0
 Inv_DP  ,271,2,0,0,0,0,19,4,0
-</syntaxhighlight><br />
+</syntaxhighlight>
-===Flowline Mk3 Refurb Notes (Nextmove E100)===
+*
+==2.6. Flowline Mk3 Refurb Notes (Nextmove E100)==
 ====Electrical Highlights: ====
@@ Ligne 488 : / Ligne 622 : @@
 | width="170" valign="top" |'''Inverter OK Output'''
 | width="227" valign="top" |X27
-| width="132" valign="top" |MB
+| width="132" valign="top" |M6
+|-
+|'''Inverter OK Internal Link'''
+|0.5mm Blue link between MB and M5
+|MB and M5
 |-
 | width="170" valign="top" |'''Output 24v Supply'''
@@ Ligne 544 : / Ligne 682 : @@
 ====Front end====
-*Ensure inverter alarm is correct sense
+*Update software to latest version 5 - see [https://stuga.dokit.app/wiki/Upgrading_To_Version_5_Software_64_bit Upgrading to Version 5]
+*Ensure inverter alarm is correct sense (High when inverter OK)
 *Parameter Invert300hz=1
 *Parameter InverterOKHigh=1
@@ Ligne 565 : / Ligne 704 : @@
 | width="75" valign="top" |'''C1-01'''
 | width="142" valign="top" |50Hz Accel  Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.4
 |-
 | width="75" valign="top" |'''C1-02'''
 | width="142" valign="top" |50Hz Decel Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.2
 |-
 | width="75" valign="top" |'''C1-05'''
@@ Ligne 577 : / Ligne 716 : @@
 | width="75" valign="top" |'''C1-06'''
 | width="142" valign="top" |300Hz Decel Time
-| width="85" valign="top" |0.4
+| width="85" valign="top" |0.2
+|-
+|'''H2-03'''
+|!Alarm
+|110
 |}
-===ZX3/Microline Replace VXR Notes (Nextmove E100)===
+==2.7. ZX4/ZX3/Microline Replace VXR Notes (Nextmove E100)==
 {{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa In ZX Cabinet.jpg|0=200px|hash=|jsondata=|mediaClass=Image|type=frameless|align=right|src=https://stuga.dokit.app/images/1/1b/Fitting_Yaskawa_Inverter_Yaskawa_In_ZX_Cabinet.jpg|href=./Fichier:Fitting Yaskawa Inverter Yaskawa In ZX Cabinet.jpg|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa In ZX Cabinet.jpg|caption=|size=200px}}
@@ Ligne 589 : / Ligne 732 : @@
 *The phase monitoring device (if fitted) is not needed any more, but it is inactive, so can be left in place.
 *Ensure 24v connected to MC, M1 and M3
-*The Zx3 and Microline have a set of switchover contactors to select 50Hz (Mains) or 300Hz (Inverter). Therefore, the inverter does not need to do the 50 / 300Hz switching as on later machine models.
+*The Zx3 and Microline have a set of switchover contactors to select 50Hz (Mains) or 300Hz (Inverter). These need to be removed as the Yaskawa will do the switching. The Y5 Hz50 Output will be used to do this on S1 and S2
@@ Ligne 601 : / Ligne 744 : @@
 {{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter ZX Cabinet IO Slices.png|0=1094px|hash=bbaee5ed05e343611e0ee7e4a06a127d|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1708,"height":993,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.64,"scaleY":0.64,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/e/e4/Fitting_Yaskawa_Inverter_ZX_Cabinet_IO_Slices.png","filters":[]},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":448.5,"top":332,"width":437,"height":310,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-218.5,"x2":218.5,"y1":-155,"y2":155,"x2a":206.81627880511354,"y2a":136.90329701188196,"x2b":197.55888948775942,"y2b":149.95322969473276},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":230,"top":177,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":667,"top":487,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":683.5,"top":571.5,"width":337,"height":1,"fill":"rgba(255,0,0,0)","stroke":"#0054FF","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-168.5,"x2":168.5,"y1":0.5,"y2":-0.5,"x2a":148.5238268195071,"y2a":7.5593116990818,"x2b":148.4763492837246,"y2b":-8.440617859625513},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":515,"top":572,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":852,"top":571,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":225.47,"top":161,"width":56.73,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Y271","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":489,"top":574,"width":47.8,"height":22.6,"fill":"#0054FF","stroke":"#0054FF","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"X308","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":636,"width":1094}|mediaClass=Image|type=frameless|align=center|src=/images/thumb/e/e4/Fitting_Yaskawa_Inverter_ZX_Cabinet_IO_Slices.png/ia-bbaee5ed05e343611e0ee7e4a06a127d-px-Fitting_Yaskawa_Inverter_ZX_Cabinet_IO_Slices.png.png|href=./Fichier:Fitting Yaskawa Inverter ZX Cabinet IO Slices.png|resource=./Fichier:Fitting Yaskawa Inverter ZX Cabinet IO Slices.png|caption=|size=1094px}}<br />
-*New Cable X308 (InA_InvZero) from M2, connect to input channel 8 on 1st IO slice (labelled 8)..
+*New Cable X308 (InA_InvZero) from M2, connect to input channel 8 on 1st IO slice (labelled 8).
+{{Idea|...If the wires cannot be added as per above diagram, You can wire to any spare channel, however you must change the ioDef file accordingly to remap the input (ASK FOR HELP!)}}<br />
 *A link wire between M4 and S8 needs to be added
 *2 additional 24v control relays needed for interfacing Estop to the STO inputs as per diagram
@@ Ligne 624 : / Ligne 769 : @@
 |-
 | width="170" valign="top" |'''Input: Select 50Hz #1'''
-| width="227" valign="top" |Not connected (constant 300Hz)
+| width="227" valign="top" |Y5 (Hz50)
 | width="132" valign="top" |S1
 |-
 | width="170" valign="top" |'''Input: Select 50Hz #2'''
-| width="227" valign="top" |Not connected  (constant 300Hz)
+| width="227" valign="top" |Y5 (Hz50)
 | width="132" valign="top" |S2
 |-
@@ Ligne 665 : / Ligne 810 : @@
 Remove  wire 30A
-| width="132" valign="top" |MB
+| width="132" valign="top" |M6
+|-
+|'''Inverter OK Internal Link'''
+|0.5mm Blue Link between MB and M5
+|M5 and MB
 |-
 | width="170" valign="top" |'''Output 24v Supply'''
@@ Ligne 696 : / Ligne 845 : @@
 InZRO,608,1,8,7,0,0,18,2,1
-Edit the following iodefs to put the all the spindle control on the spindle IO screen – makes testing much easier
+Edit the Column and row values for the following iodefs to put the all the spindle control on the spindle IO screen – makes testing much easier (items 8 and 9 in the csv)
 INVOK,542,1,8,23,0,0,18,6,0
 HZ50,578,2,0,4,0,0,18,7,D
 HZ300,579,2,0,5,0,0,18,8,E
 SMOT,558,2,8,15,0,1,18,3,Z
-RST,574,2,8,18,0,0,18,4,F
+SRST,574,2,8,18,0,0,18,4,F
-</syntaxhighlight><br />
+</syntaxhighlight>****** GLENN NOTE   *******
+On a '''<u>Microline</u>''', check in IODef.mul for <syntaxhighlight>
+CLSIP,607,2,9,3,0,0,2,3,X
+CLSOV,608,2,9,4,0,0,2,4,Y
+CLSOP,609,2,9,5,0,0,2,5,Z
+</syntaxhighlight>
+change CLSOV from reference 608 to 618
+See [https://stuga.dokit.app/wiki/Microline_Issue_-_Saw_Outfeed_Clamp_Does_not_Come_on Microline Issue Saw Outfeed Clamp]<br />
 ====Alarms.mul====
 Ensure the alarms are set for each individual spindle:<syntaxhighlight>
@@ Ligne 744 : / Ligne 903 : @@
 | width="75" valign="top" |'''C1-01'''
 | width="142" valign="top" |50Hz Accel Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.4
 |-
 | width="75" valign="top" |'''C1-02'''
 | width="142" valign="top" |50Hz  Decel Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.2
 |-
 | width="75" valign="top" |'''C1-05'''
 | width="142" valign="top" |300Hz Accel Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.4
 |-
 | width="75" valign="top" |'''C1-06'''
 | width="142" valign="top" |300Hz  Decel Time
-| width="85" valign="top" |0.5
+| width="85" valign="top" |0.2
+|-
+|'''H2-03'''
+|!Alarm
+|110
 |}
-=Checklist=
+===2.7.1 Anomalies with M008 Upgrade===
+When upgrading M008, the wiring did not match the expectations above. These anomalies are noted here for guidance on a similar upgrade in future
+<br />
+{| class="wikitable"
+|+
+!
+!
+!Details
+!Solution
+|-
+|1
+|Hz50 / Hz300 Outputs
+|The wiring diagram only shows a Hz300 output on Y6, but the backend software needs Y5 Hz50 to do the switching. Y5 is the main saw motor!
+|Swap the mapping channel of the Hz50 and Hz300 outputs to ensure Hz50 is connected to the inverter S1, S2 using Y6 (DOUT5)<syntaxhighlight>
+HZ300,579,2,0,9,0,0,18,8,F
+HZ50,578,2,0,5,0,1,18,7,J
+</syntaxhighlight><br />
+|-
+|2
+|Reset
+|Inverter reset on the drawings is not connected, yet physically connected via the servo cards to Y43, not Y34
+|
+|-
+|3
+|Nodes
+|The system uses Beckhoff IO slices, not Wago, therefore needs two sets of nodes. This is a different diagram to the one published. Pictures are below
+|Different IoDef mapping needed<syntaxhighlight>
+INVDP,616,2,9,13,0,0,18,1,1
+InZRO,608,1,8,15,0,0,18,2,1
+</syntaxhighlight><br />
+|-
+|4
+|InvOK
+|Labelled X14 on the drawing  and physically in the machine, wired through the overload relay
+|Wire directly from DIN13 on nextmove - keep same mapping to channel 0,13<br />
+|}
+=2.8 Autoflow with Delta Inverter=
+{| class="wikitable" border="1" cellspacing="0" cellpadding="0"
+| width="170" valign="top" |'''Function'''
+| width="227" valign="top" |'''Wire Number / Colour'''
+| width="132" valign="top" |'''Yaskawa Terminal'''
+|Notes
+|-
+| width="170" valign="top" |'''Mains  In L1, L2, L3'''
+| width="227" valign="top" |21B, 22B,  23B
+| width="132" valign="top" |L1, L2, L3
+|
+|-
+| width="170" valign="top" |'''Motor Out U, V, W'''
+| width="227" valign="top" |29B, 30B, 31B
+| width="132" valign="top" |T1, T2, T3
+|Ther emay be a phase detection relay between
+B-29B
+B-30B
+B-31B
+This can be discarded
+Remove wire 61B from Phase monitor to Delta MI6. Not needed because Yaskawa does phase monitoring internally
+|-
+| width="170" valign="top" |'''Input:  Select 50Hz #1'''
+| width="227" valign="top" |Y63
+| width="132" valign="top" |S1
+| rowspan="2" |Existing Y63 OuB_Spin300 connects to S1 and add link to S2
+|-
+| width="170" valign="top" |'''Input: Select 50Hz #2'''
+| width="227" valign="top" |link to S1
+| width="132" valign="top" |S2
+|-
+| width="170" valign="top" |'''Input:  Double Plunge #1'''
+| width="227" valign="top" |Y316 -Wired  To MC2B OU1 (pin9)
+| width="132" valign="top" |S3
+| rowspan="2" |There is a cable already labelled Y55.
+*This will be relabelled Y316 (OuB_InvDp) .
+*This connects to S3 and add link to S4.
+{{Info|...This is different to the standard Y271. Only applies to TwinCAT2 controlled machines}}<br />
+|-
+| width="170" valign="top" |'''Input: Double Plunge #2'''
+| width="227" valign="top" |Link to S3
+| width="132" valign="top" |S4
+|-
+| width="170" valign="top" |'''Input:  Motor Run'''
+| width="227" valign="top" |Y62
+| width="132" valign="top" |S5
+|Existing wire
+|-
+| width="170" valign="top" |'''Input: Inverter Reset'''
+| width="227" valign="top" |Y374
+| width="132" valign="top" |S6
+|Existing Wire
+|-
+| width="170" valign="top" |'''Input:  Resistor Thermal Ovl'''
+| width="227" valign="top" |n/c
+| width="132" valign="top" |S7
+|
+|-
+| width="170" valign="top" |'''Input: Motor 2 Safety'''
+| width="227" valign="top" |Link to M4
+| width="132" valign="top" |S8
+|A link wire between M4 and S8 needs to be added
+|-
+| width="170" valign="top" |'''Inverter  OK 24v'''
+| width="227" valign="top" |24v  (Yellow)
+| width="132" valign="top" |MC
+|Ensure 24v connected to MC, not through an auxilliary contact
+Remove Wire 60B (From Aux contact on F5 to RC1 on Delta Inverter). Not needed because Inverter OK signal does not need to be in series with F5 overload
+|-
+| width="170" valign="top" |'''Inverter OK Output'''
+| width="227" valign="top" |X90
+| width="132" valign="top" |M6
+|Ensure this connected directly to MC2B Pin 3 and does not go through any auxilliary
+|-
+| width="170" valign="top" |'''Output  24v Supply'''
+| width="227" valign="top" |24v  (Yellow)
+| width="132" valign="top" |M1, M3
+|Ensure 24v connected to M1, M3
+|-
+| width="170" valign="top" |'''Output: Spindle At Zero'''
+| width="227" valign="top" |X308 -To io slice MC2B  IN6 (pin6)
+| width="132" valign="top" |M2
+|'''Reuse an existing cable for this new connection'''
+There is a cable already labelled Y59
+*This will be relabelled X308 (InA_InvZero)
+*At Yaskawa end, this connects to M2
+*At Beckhoff end, this was connected to MC2B pin 15 (OU1). This now needs to be moved to pin 6 (IN4)
+|-
+| width="170" valign="top" |'''Output:  Motor 2 Safety'''
+| width="227" valign="top" |Link to S8
+| width="132" valign="top" |M4
+|A link wire between M4 and S8 needs to be added
+|-
+|'''InvOK Internal Link'''
+|0.5mm Blue Link between MB and M5
+|M5 and MB
+|
+|-
+| width="170" valign="top" |'''STO Override'''
+| width="227" valign="top" |Add 2 relays as per diagram.
+Relay control via Beckhoff  safety slices
+| width="132" valign="top" |H1, H2, HC
+|{{#annotatedImageLight:Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|0=271px|hash=838c64a3e48db156512f36c909a0e67a|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":271,"height":203,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/4/42/Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png","filters":[]},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":38,"top":16,"width":47.8,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"SY9","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":144,"top":15,"width":48.93,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"SY11","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":38.45,"top":189.63,"width":48.93,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.14,"scaleY":1.14,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"SY10","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":147,"top":190.94,"width":48.93,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1.4,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"SY12","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":203,"width":271}|mediaClass=Image|type=frameless|alt=Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|align=left|src=/images/thumb/4/42/Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png/ia-838c64a3e48db156512f36c909a0e67a-px-Fitting_Yaskawa_Inverter_Yaskawa_STO_Wiring_Beckhoff.png.png|href=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|resource=./Fichier:Fitting Yaskawa Inverter Yaskawa STO Wiring Beckhoff.png|caption=|size=271px}}
+|-
+| width="170" valign="top" |'''External  0v'''
+| width="227" valign="top" |0v (White)
+| width="132" valign="top" |SC
+|
+|-
+| width="170" valign="top" |'''Braking Resistor'''
+| width="227" valign="top" |1,2
+| width="132" valign="top" |B1, B2
+|Replace braking resistor if supplied. If not supplied, check the resistor is not short cuircuit - this has been the root casue of failure in the past
+|}
+'''IODef.mul additions'''<syntaxhighlight>
+InB_InvZero,308,1,0,0,0,0,19,7,0
+OuB_InvDP,271,2,0,0,0,0,19,8,0
+</syntaxhighlight>'''Alarms.mul additions / changes'''
+<syntaxhighlight>
+,InB_InvSpinOk,False,OuB_Spin1On,True,0,4,Spindle 1 Alarm,True,False
+,InB_InvSpinOk,False,OuB_Spin2On,True,0,4,Spindle 2 Alarm,True,False
+,InB_InvSpinOk,False,OuB_Spin3On,True,0,4,Spindle 3 Alarm,False,False
+,InB_InvSpinOk,False,OuB_Spin4On,True,0,4,Spindle 4 Alarm,True,False
+,InB_InvSpinOk,False,OuB_Spin5On,True,0,4,Spindle 5 Alarm,True,False
+,InB_InvSpinOk,False,OuB_Spin6On,True,0,4,Spindle 6 Alarm,True,False
+,InB_InvSpinOk,False,OuB_Spin7On,True,0,4,Spindle 7 Alarm,False,False
+,InB_InvSpinOk,False,OuB_Spin8On,True,0,4,Spindle 8 Alarm,True,False
+,InF_GtOpen,0,OuF_Gate,True,30,3,Safety Gate Not Open,False,False,0
+,InF_GtClosed,0,OuF_Gate,False,30,3,Safety Gate Not Closed,False,False,0
+</syntaxhighlight><br />
+{| class="wikitable"
+|+Change IO Links in Beckhoff Software
+!Module
+!Slice
+!IO Channel
+!Was
+!Change To
+!Notes
+|-
+|Module B
+|MC2B
+|Output 0
+|Y55
+|Y271
+| rowspan="2" |Were duplicates of the Double plunge output for spindles 2+5.
+Now change to Ou_InvDP
+This needs to be a seperate output from the spindle DP becasue the timing is different and crucial
+|-
+|Module B
+|MC2B
+|Output 1
+|Y59
+|Blank
+|-
+|Module B
+|MC2B
+|Input 6
+|Blank
+|X308
+|New input for Inverter at Zero
+|}
+=3. Completion=
+==3.1. Checklist==
 {| class="wikitable"
 |+General Item Checklist before power on
@@ Ligne 766 : / Ligne 1 141 : @@
 |-
 |Inverter Replaced
+|
+|-
+|If the old braking resistor is reused, test the resistance matches the stated value.
+If an ohmmeter is not available, ensure it is not a dead short to ground or open circuit
 |
 |-
@@ Ligne 801 : / Ligne 1 180 : @@
 |
 |-
-|Back End updated if required
+|Back End updated if required{{Warning|...If this is a Nexmove, set the YASKAWAINVERTER parameter to _TRUE}}{{#annotatedImageLight:Fichier:YASKAWAINVERTER parameter.png|0=500px|hash=43b3099b08daf2a8e6446b2b60d9f1ce|jsondata={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":500,"height":43,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/b/b2/YASKAWAINVERTER_parameter.png","filters":[]}],"height":43,"width":500}|mediaClass=Image|type=frameless|align=center|src=/images/thumb/b/b2/YASKAWAINVERTER_parameter.png/ia-43b3099b08daf2a8e6446b2b60d9f1ce-px-YASKAWAINVERTER_parameter.png.png|href=./Fichier:YASKAWAINVERTER parameter.png|resource=./Fichier:YASKAWAINVERTER parameter.png|caption=|size=500px}}<br />
 |
 |-
@@ Ligne 815 : / Ligne 1 194 : @@
 |-
 |Check Inverter accel and decel parameters
+- Double check that psInvDecel300Hz=400
+'''Inverter Deceleration Parameters C1-02, C1-06''' are set to 0.2
+'''Inverter Acceleration Parameters C1-01, C1-05''' are set to 0.4
+{{Info|...the ps is set in milliseconds, the inverter parameter in seconds
+The inverter deceleration time must be LESS than the front end parameter, otherwise the relay contacts will open before the inverter has finished decelerating the spindles, leading to burning and arcing}}<br />
+|
+|-
+|Check Inverter DC Injection parameters set to zero
+Parameters B2 -02 and B2-04
 |
 |-
-|Check Inverter DC Injection parameters set to zero
+|Check parameter H2-03 is set to 110
 |
 |-
 |Test InverterOK signal (high when OK)
 Ensure alarm triggers on InvOK low
+|
+|-
+|Ov connected to SC
+|
+|-
+|24v Connected to M1, M3, MC
+|
+|-
+|Update [https://stugaltd.monday.com/boards/304269981 Control Systems Log] for the software version and Inverter type
 |
 |}
-=Testing=
+==3.2. Testing==
 For this machine type, testing a spindle should follow this process
@@ Ligne 851 : / Ligne 1 250 : @@
 =====Double 300Hz Elte Motor=====
-Same as single, but select double plunge spindles and set InvDP to tell inverter to double the output power</translate>
+Same as single, but select double plunge spindles and set InvDP to tell inverter to double the output power
+Test InvZro input to system is low when inverter running, high when spindle stops</translate>
 {{PageLang
 |Language=en

Fitting Yaskawa Inverter : Différence entre versions

Version actuelle datée du 15 novembre 2024 à 13:02

Sommaire

1. Introduction-Upgrade Kit

1.1 What is the Yaskawa inverter?

1.2 Mechanical Fitting Notes

In place of a Delta inverter

In place of a Jaguar inverter

1.3 Wiring the Yaskawa Inverter

1.4 Software Upgrades

Extra Functionality

TwinCAT3 Notes

2. Machine Applications

2.1. Autoflow TwinCAT 2 Notes

Inverter

Back end

Front end

2.2. Flowline Mk3 Refurb TwinCAT3

IODef.mul additions

2.3. ZX3/4 Mk5/6 (Beckhoff and TwinSAFE) Retrofitting in place of Delta

IODef.mul additions

Mapping

2.4. ZX5 Retrofitting in place of Delta

IODef.mul additions

2.6. Flowline Mk3 Refurb Notes (Nextmove E100)

Electrical Highlights:

IODef.mul additions

Alarms.mul

Front end

Other software

2.7. ZX4/ZX3/Microline Replace VXR Notes (Nextmove E100)

Electrical Highlights:

IODef.mul additions

Alarms.mul

Front end

Other software

2.7.1 Anomalies with M008 Upgrade

2.8 Autoflow with Delta Inverter

3. Completion

3.1. Checklist

3.2. Testing

50Hz V notch motor

Single 300Hz Elte Motor

Double 300Hz Elte Motor

Commentaires