WinMulti - Drives : Différence entre versions

[version en cours de rédaction]

Version du 9 avril 2020 à 14:04

This Page describes the drives screen in the winMulti Service Menu

Auteur Stuga Engineer | Dernière modification 16/04/2020 par Stuga Engineer en cours de rédaction ⧼frevu-button-review-label⧽

Pas encore d'image

This Page describes the drives screen in the winMulti Service Menu

winMulti, Drives, WinMulti, Motors

Drives

The Drives tab allows manipulation of each of the axes. Each Machine type will have different drives as shown below. The manipulation of these can only be performed in Manual Mode, to enter manual mode from the main screen press the STOP Button once.

Saw Drives

Autocut Drives
Drive	Description
GX Axis	This is the axis for the saw pusher and works from 7060 (end if the infeed bed) to 0 (Saw Blade)
SR Axis	This is the axis for the Saw Blade Rotation and works from 45 to 135 degrees

Axes

+ / - Buttons

Once in Manual Mode tapping on the + and – buttons next to each of the drives will jog the axis in the appropriate direction, and the numbers between the +/- buttons show the current axis position.

Home

Tapping on the Home Button will move the axis back to its home position, as determined in the Settings – Axis screen.

Move & Stop

Type the position required into the Numbers after the Move button. When the move button is then pressed, the drive will attempt to move to the axis position given. Stop can be pressed at any point to halt this movement.

Reverse

The Reverse button reverses the direction of the associated drive.

Numbers

The Numbers after the Reverse button are (In order) Maximum Position, Speed, Acceleration, Deceleration

Ecoline

Ecoline Drives
Drive	Description
X Axis	This is the Gripper axis along the bar and works from the end of the infeed bed to the centre of the tools on the Ring
Y Axis	This is the Axis Away and Toward the operator and works from -104 to 1119
Z Axis	This is the Up and Down axis and works from -114 to 110
G Axis	This is the Gripper Forward/Back Axis and works from 23mm from the back fence to 52mm from the back fence
V Axis	This is the V Notch Module axis and works from 5 to 250 home position is around 128mm
R Axis	This is the Ring Angle and works from 0 degrees to 359 degrees, at 90 degrees the tool is closest to the operator.

Flowline / ZX3 Drives

Microline

ZX4 Drives

ZX5 Drives

Autoflow Drives

Speed Override

The speed override slider slows down the motor movements to give the operator time to intervene in diagnostic exercises.

Save

The Save Button saves and setting changes (e.g. Inverter frequencies)

Setup Mode

This puts the machine into setup mode.

Test Printer

This button sends a test label to the printer.

to return to the main page, please click WinMulti Software Operating Guide

en none 0

Commentaires

Draft

@@ Ligne 21 : / Ligne 21 : @@
 |SR Axis
 |This is the axis for the Saw Blade Rotation and works from 45 to 135 degrees
-|}
+|}<br />
-<br />
-===Ecoline===
-{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesEcoline.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=default|src=https://stuga.dokit.app/images/7/73/WinMulti_-_Drives_DrivesEcoline.jpg|href=./Fichier:WinMulti - Drives DrivesEcoline.jpg|resource=./Fichier:WinMulti - Drives DrivesEcoline.jpg|caption=Ecoline Drives|size=997px}}
-===Flowline / ZX3 Drives===
-===Microline===
-===ZX4 Drives===
-===ZX5 Drives===
-<br />{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesZX5.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/5/5f/WinMulti_-_Drives_DrivesZX5.jpg|href=./Fichier:WinMulti - Drives DrivesZX5.jpg|resource=./Fichier:WinMulti - Drives DrivesZX5.jpg|caption=ZX5 Drives|size=997px}}<br />
-===Autoflow Drives===
-{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesAutoflow.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/b/b0/WinMulti_-_Drives_DrivesAutoflow.jpg|href=./Fichier:WinMulti - Drives DrivesAutoflow.jpg|resource=./Fichier:WinMulti - Drives DrivesAutoflow.jpg|caption=Autoflow Drives|size=997px}}<br />
-<br />
 ====Axes====
 <br />+ / - Buttons
@@ Ligne 55 : / Ligne 33 : @@
 =====Move & Stop=====
-Type the position required into the Numbers between the Move and Stop buttons. When the move button is then pressed, the drive will attempt to move to the axis position given. Stop can be pressed at any point to halt this movement.
+Type the position required into the Numbers after the Move button. When the move button is then pressed, the drive will attempt to move to the axis position given. Stop can be pressed at any point to halt this movement.
 <br />
@@ Ligne 66 : / Ligne 44 : @@
 <br />
-====Inverters====
+===Ecoline===
-The inverters section is only populated for Autoflow machines, each inverter has a Fwd and Rev button which starts the inverter going forward or backward the numbers to the right of these denote the Hertz value required for that inverter. The Stop Button will cease movement.
+{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesEcoline.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=default|src=https://stuga.dokit.app/images/7/73/WinMulti_-_Drives_DrivesEcoline.jpg|href=./Fichier:WinMulti - Drives DrivesEcoline.jpg|resource=./Fichier:WinMulti - Drives DrivesEcoline.jpg|caption=Ecoline Drives|size=997px}}
+{| class="wikitable"
+|+Ecoline Drives
+!Drive
+!Description
+|-
+|X Axis
+|This is the Gripper axis along the bar and works from the end of the infeed bed to the centre of the tools on the Ring
+|-
+|Y Axis
+|This is the Axis Away and Toward the operator and works from -104 to 1119
+|-
+|Z Axis
+|This is the Up and Down axis and works from -114 to 110
+|-
+|G Axis
+|This is the Gripper Forward/Back Axis and works from 23mm from the back fence to 52mm from the back fence
+|-
+|V Axis
+|This is the V Notch Module axis and works from 5 to 250 home position is around 128mm
+|-
+|R Axis
+|This is the Ring Angle and works from 0 degrees to 359 degrees, at 90 degrees the tool is closest to the operator.
+|}
 <br />
+===Flowline / ZX3 Drives===
-====Speed Override====
-The speed override slider slows down the motor movements to give the operator time to intervene in diagnostic exercises.
+===Microline===
+===ZX4 Drives===
+===ZX5 Drives===
+<br />{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesZX5.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/5/5f/WinMulti_-_Drives_DrivesZX5.jpg|href=./Fichier:WinMulti - Drives DrivesZX5.jpg|resource=./Fichier:WinMulti - Drives DrivesZX5.jpg|caption=ZX5 Drives|size=997px}}<br />
-<br />
+===Autoflow Drives===
+{{#annotatedImageLight:Fichier:WinMulti - Drives DrivesAutoflow.jpg|0=997px|hash=|jsondata=|mediaClass=Image|type=frameless|align=center|src=https://stuga.dokit.app/images/b/b0/WinMulti_-_Drives_DrivesAutoflow.jpg|href=./Fichier:WinMulti - Drives DrivesAutoflow.jpg|resource=./Fichier:WinMulti - Drives DrivesAutoflow.jpg|caption=Autoflow Drives|size=997px}}<br />
+====Speed Override====
+The speed override slider slows down the motor movements to give the operator time to intervene in diagnostic exercises.
 ====Save====
@@ Ligne 87 : / Ligne 98 : @@
 ====Test Printer====
 This button sends a test label to the printer.
+<br />
+to return to the main page, please click [[Manual:WinMulti Software Operating Guide|WinMulti Software Operating Guide]]
+<br />
 <br /></translate>
 {{PageLang