R0015087 Pneumatic Connections : Différence entre versions

[version en cours de rédaction]

Version actuelle datée du 11 mars 2024 à 15:48

Instructions to install pneumatic connections to main frame

Auteur Gareth Green | Dernière modification 11/03/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Moyen

Durée

8 heure(s)

Instructions to install pneumatic connections to main frame

Difficulté

Moyen

Durée

8 heure(s)

Sommaire

1 Introduction
2 Étape 1 - Unless otherwise stated
3 Étape 2 - mount pneumatic rail
4 Étape 3 - Valve Bank Connections
5 Étape 4 - Y239 Material blower
6 Étape 5 - Y231, Y230 and Y299 Pop up feeds
7 Étape 6 - Y221 channel
8 Étape 7 - Y220 channel lock
9 Étape 8 - Y147 pop up E
10 Étape 9 - Y146 Roller Bed
11 Étape 10 - Important
12 Étape 11 - Y131 Grip Height
13 Étape 12 - Y241 Rack blower
14 Étape 13 - Cable looms
15 Étape 14 - Connect ring main
16 Commentaires

Introduction

Tools require

Pipe cutters

Number identification

Flush cutters

Parts required

P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 8

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000551 6mm inline Quick Exhaust Fitting x 7

P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x1

P0001022 Regulator Bracket: to suit P0001008 x 1

A0000343 energy chain x 1

A0000344 energy chain bracket set x 1

D0015577 Fixed energy chain bracket x 1

P0001030 6mm compact tee x 12

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

R0015086 Assemble Pneumatics on to electrical cabinet loctite 243.png

Étape 2 - mount pneumatic rail

Mount pre assembled pneumatic rail with 2 off M8 x 20 socket cps. Use 1 off M8 A Form washer on slotted end of rail

Étape 3 - Valve Bank Connections

Valve bank connections are as follows

Front row of valve bank (4) is the active ports, These will all be connected with suffix 9 pipe identifications

Back row (2) is the home position , these will always be connected with suffix 1 pipe identifications

Étape 4 - Y239 Material blower

Material blower should be identified as 2399

Located on roller assembly close to saw unit

P0000160 flow reg required to control flow onto sensors, this should be pre fitted to roller assembly at bench assembly stage

Connect to active port ln valve bank (4)

Étape 5 - Y231, Y230 and Y299 Pop up feeds

Feed pipes from valve bank should be run to transfer arm location 4

Identifications will be

2319

2309

2299

Connect to active port on valve bank (4)

Fit A000343 energy chain @40 links

A0000344 energy chain brackets as shown

Mount to D0015577 fixed bracket with M3 x 6 panhead screws and attach to support arm as shown using M4 x 16 socket caps, A form washers and M4 nyloc nuts .

Must have a P0000551 Q.E.V fitted to each line

Ensure 1.5 m of pipe is left exiting the end of the energy chain

Étape 6 - Y221 channel

Use schematic for pneumatic connections

Ensure P0000551 Q.E.V are fitted

Étape 7 - Y220 channel lock

Identification 2209

Connected to active port of valve bank (4)

Étape 8 - Y147 pop up E

Identification 1479

Connects to active port on valve bank (4)

Use P0001030 compact tee to connect

Ensure enough loom to allow full range of movement

Étape 9 - Y146 Roller Bed

Identification

1461 and 1469

Roller bed is lifted at home position

Use P0001030 6mm tee for connections

1461 to home port on valve bank (2)

1469 to active port on valve bank (4)

Étape 10 - Important

It is vital that when installing pipes into the main X axis energy chain, that cable retaining points are used

All cables and pipes should be secured with tie wraps to the 'fingers' on the energy chain brackets at BOTH ends

R0015338 Bench Assemble Serial Plate caution.png

Étape 11 - Y131 Grip Height

Fit tie bases as shown to gripper support arms .

Ecr raised to add holes to drawing 06/11/23

Fit P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge x1

P0001022 Regulator Bracket: to suit P0001008 x 1 to bracket shown

Gripper height is lifted for home position

identification

1311 Home port of valve bank (2) to nose of cylinder

1312 base of cylinder to out port on regulator

Ensure P0000551 Q.E.V are fitted to both grip height cylinder ports

1319 In port of regulator to active port on valve bank (4)

R0015087 Pneumatic Connections Screenshot 2023-11-06 092048.png

R0015087 Pneumatic Connections Screenshot 2023-11-22 074301.png

Étape 12 - Y241 Rack blower

Identification 2419

Must have flow regulation P0000160

Split feed with P0001030 6mm tee

Connect to active port (4) on valve bank

Étape 13 - Cable looms

Install 1 off cable tie base as shown

Run cable X44 and X10 as shown

Leave loops of excess cable tied off ready for electrical termination

Leave cable X283 tied off in a loop on cylinder

Étape 14 - Connect ring main

Connect 12mm blue airpipe from valve banks to end of frame for machine connections

Commentaires

en none 0 Draft

@@ Ligne 1 : / Ligne 1 : @@
 {{Tuto Details
+|Main_Picture=R0015114_Bench_Assemble_Valve_Banks_and_Regulators_Screenshot_2023-11-02_074048.png
+|Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":26,"top":-37,"width":126,"height":119,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":4.68,"scaleY":4.68,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/4/4e/R0015114_Bench_Assemble_Valve_Banks_and_Regulators_Screenshot_2023-11-02_074048.png","filters":[]}],"height":450.4109589041096,"width":600}
 |Description=<translate>Instructions to install pneumatic connections to main frame</translate>
 |Categories=Production
@@ Ligne 20 : / Ligne 22 : @@
-P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread)
+P0000010 Elbow Adaptor 6mm - 1/8 BSPT (Taper thread) x 8
-P0000160 Fitting: Flow Controller In Line 6mm
+P0000160 Fitting: Flow Controller In Line 6mm x 2
-P0000551 6mm inline Quick Exhaust Fitting
+P0000551 6mm inline Quick Exhaust Fitting x 7
-P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge
+P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge  x1
-P0001022 Regulator Bracket: to suit P0001008
+P0001022 Regulator Bracket: to suit P0001008 x 1
+A0000343 energy chain x 1
+A0000344 energy chain bracket set  x 1
+D0015577 Fixed energy chain bracket x 1
+P0001030 6mm compact tee x  12
 <br /></translate>
@@ Ligne 42 : / Ligne 52 : @@
 All bolts to be pen marked once adhesive applied and correct tension added</translate>
 |Step_Picture_00=R0015086_Assemble_Pneumatics_on_to_electrical_cabinet_loctite_243.png
+}}
+{{Tuto Step
+|Step_Title=<translate>mount pneumatic rail</translate>
+|Step_Content=<translate>Mount pre assembled pneumatic rail with 2 off M8 x 20 socket cps. Use 1 off M8 A Form washer on slotted end of rail</translate>
+}}
+{{Tuto Step
+|Step_Title=<translate>Valve Bank Connections</translate>
+|Step_Content=<translate>Valve bank connections are as follows
+Front row of valve bank (4) is the active ports, These will all be connected with suffix 9 pipe identifications
+Back row  (2) is the home position , these will always be connected with suffix 1 pipe identifications</translate>
+|Step_Picture_00=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_084819.png
+|Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":584,"height":544,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.03,"scaleY":1.03,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/f/fb/R0015087_Pneumatic_Connections_Screenshot_2023-11-06_084819.png","filters":[]},{"type":"wfline","version":"2.4.6","originX":"center","originY":"center","left":384.5,"top":319,"width":281,"height":96,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-140.5,"x2":140.5,"y1":48.000733743326975,"y2":-48.000733743326975},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":244,"top":367,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":525,"top":271,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfline","version":"2.4.6","originX":"center","originY":"center","left":395.5,"top":353.5,"width":291,"height":99,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":-145.5,"x2":145.5,"y1":49.50075667280592,"y2":-49.50075667280592},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":250,"top":403.01,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":541,"top":304,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfnumberedbullet","version":"2.4.6","originX":"left","originY":"top","left":197,"top":406,"width":25,"height":25,"fill":"rgb(0,0,0)","stroke":"#FF0000","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"objects":[{"type":"circle","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":24,"height":24,"fill":"#FF0000","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":12,"startAngle":0,"endAngle":6.283185307179586},{"type":"text","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":7.79,"height":15.82,"fill":"rgba(255,255,255,255)","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"2","fontSize":14,"fontWeight":"normal","fontFamily":"arial","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"styles":{} }],"number":2},{"type":"wfnumberedbullet","version":"2.4.6","originX":"left","originY":"top","left":196,"top":363,"width":25,"height":25,"fill":"rgb(0,0,0)","stroke":"#FF0000","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"objects":[{"type":"circle","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":24,"height":24,"fill":"#FF0000","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":12,"startAngle":0,"endAngle":6.283185307179586},{"type":"text","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":7.79,"height":15.82,"fill":"rgba(255,255,255,255)","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"4","fontSize":14,"fontWeight":"normal","fontFamily":"arial","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"styles":{} }],"number":4},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":201.03,"top":478.89,"width":232.52,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.6,"scaleY":1.6,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Pipes ending in 1\n","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} },{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":160.03,"top":332.83,"width":187.52,"height":22.6,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.44,"scaleY":1.44,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"Pipes ending in 9","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":559,"width":600}
 }}
 {{Tuto Step
@@ Ligne 48 : / Ligne 74 : @@
-P0000160 flow reg required to control flow onto sensors
+Located on roller assembly close to saw unit
+P0000160 flow reg required to control flow onto sensors, this should be pre fitted to roller assembly at bench assembly stage
@@ Ligne 73 : / Ligne 102 : @@
 Connect to active port on valve  bank (4)
-Fit A000343 energy chain @44? links
-A0000344 energy chain brackets as shown
+Fit A000343 energy chain @40  links
-Mount to D0015577 fixed bracket and attach to support arm as shown
-Must have a P0000551 qev fitted to each line
+A0000344 energy chain brackets as shown
-<br /></translate>
-}}
-{{Tuto Step
-|Step_Title=<translate>Y221 channel</translate>
-|Step_Content=<translate>Has regulation on active position
+Mount to D0015577 fixed bracket  with M3 x 6 panhead screws and attach to support arm as shown using M4 x 16 socket caps, A form washers and M4 nyloc nuts .
-Identification
+Must have a P0000551 Q.E.V  fitted to each line
-feeds from valve bank (2) to cylinder home port  (nose)
+Ensure 1.5 m of pipe is left exiting the end of the energy chain
-feeds from base of cylinder to reg out port
+<br /></translate>
+|Step_Picture_00=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085457.png
+|Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1357,"height":854,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.44,"scaleY":0.44,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/7/71/R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085457.png","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":137.42,"top":129.42,"width":66.95,"height":66.95,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":33.47514634261764,"ry":33.47514634261764},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":46,"top":170,"width":70.05,"height":75.03,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"4th Support arm ","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":378,"width":600}
-feeds from reg in port to active port on valve bank (4)
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085551.png
+|Step_Picture_02=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085556.png
+|Step_Picture_03=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085616.png
+|Step_Picture_04=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085545.png
+|Step_Picture_05=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_085610.png
+}}
+{{Tuto Step
+|Step_Title=<translate>Y221 channel</translate>
+|Step_Content=<translate>Use schematic for pneumatic connections
-P0000551 2 off must be fitted to 2211 and 2212 close to cylinder</translate>
+Ensure P0000551 Q.E.V are fitted</translate>
 |Step_Picture_00=R0015087_Pneumatic_Connections_Screenshot_2023-07-17_095212.png
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1015,"height":572,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.59,"scaleY":0.59,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/5/55/R0015087_Pneumatic_Connections_Screenshot_2023-07-17_095212.png","filters":[]},{"type":"wfarrow2line","version":"2.4.6","originX":"center","originY":"center","left":191,"top":313.5,"width":124,"height":31,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":4,"strokeDashArray":null,"strokeLineCap":"round","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"x1":62,"x2":-62,"y1":-15.5,"y2":15.5,"x2a":-40.656864996802696,"y2a":18.410427500435997,"x2b":-44.537434997384025,"y2b":2.8881474981106843},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":253,"top":298,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"wfarrow2circle","version":"2.4.6","originX":"center","originY":"center","left":129,"top":329,"width":16,"height":16,"fill":"#aaa","stroke":"#666","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":0.5,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":8,"startAngle":0,"endAngle":6.283185307179586},{"type":"textbox","version":"2.4.6","originX":"center","originY":"center","left":439.74,"top":243.68,"width":282.6,"height":48.82,"fill":"#FF0000","stroke":"#FF0000","strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.27,"scaleY":1.27,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"P0000551 fitted close to this areas","fontSize":20,"fontWeight":"normal","fontFamily":"sans-serif","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"minWidth":20,"styles":{} }],"height":338,"width":600}
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_090508.png
 }}
 {{Tuto Step
@@ Ligne 118 : / Ligne 149 : @@
 Connects to active port on valve bank (4)
+Use  P0001030 compact tee to connect
@@ Ligne 132 : / Ligne 165 : @@
 Roller bed is lifted at home position
+Use P0001030  6mm tee for connections
@@ Ligne 142 : / Ligne 177 : @@
 <br /></translate>
+}}
+{{Tuto Step
+|Step_Title=<translate>Important</translate>
+|Step_Content=<translate>It is vital that when installing pipes into the main X axis energy chain, that cable retaining points are used
+All cables and pipes should be secured with tie wraps to the 'fingers' on the energy chain brackets at BOTH ends</translate>
+|Step_Picture_00=R0015338_Bench_Assemble_Serial_Plate_caution.png
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-12-06_083154.png
+|Step_Picture_01_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":471,"height":502,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.27,"scaleY":1.27,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/6/6b/R0015087_Pneumatic_Connections_Screenshot_2023-12-06_083154.png","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":287.64,"top":325.36,"width":116.33,"height":116.33,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":58.16641250764279,"ry":58.16641250764279}],"height":639,"width":600}
+}}
+{{Tuto Step
+|Step_Title=<translate>Y131 Grip Height</translate>
+|Step_Content=<translate>Fit tie bases as shown to gripper support arms .
+Ecr raised to add holes to drawing 06/11/23
+Fit P0001008 Regulator: ARG20 0 - 8.5 Bar c/w Gauge  x1
+P0001022 Regulator Bracket: to suit P0001008 x 1 to bracket shown
+Gripper height is lifted for home position
+identification
+  Home port of valve bank (2) to nose of cylinder
+  base of cylinder to out port on regulator
+Ensure P0000551 Q.E.V are fitted to both grip height cylinder ports
+In port of regulator to active port on valve bank  (4)</translate>
+|Step_Picture_00=R0015087_Pneumatic_Connections_Screenshot_2023-12-22_075047.png
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-11-06_092048.png
+|Step_Picture_02=R0015087_Pneumatic_Connections_Screenshot_2023-11-22_074301.png
 }}
 {{Tuto Step
@@ Ligne 149 : / Ligne 221 : @@
 Must have flow regulation P0000160
+Split feed with P0001030 6mm tee
@@ Ligne 154 : / Ligne 228 : @@
 |Step_Picture_00=R0015256_Pneumatic_Connections_Screenshot_2023-07-13_125718.png
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":571,"height":584,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.05,"scaleY":1.05,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/a/a6/R0015256_Pneumatic_Connections_Screenshot_2023-07-13_125718.png","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":279.89,"top":373.89,"width":101.12,"height":101.12,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":50.557887585106556,"ry":50.557887585106556}],"height":614,"width":600}
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-11-22_074301.png
+|Step_Picture_02=R0015087_Pneumatic_Connections_Screenshot_2023-12-22_075047.png
 }}
 {{Tuto Step
-|Step_Title=<translate>Y131 Grip Height</translate>
+|Step_Title=<translate>Cable looms</translate>
-|Step_Content=<translate>Gripper height is lifted for home position
+|Step_Content=<translate>Install 1 off cable tie base as shown
-identification
+Run cable X44 and X10  as shown
-  Home port of valve bank (2) to nose of cylinder
+Leave loops of excess cable tied off ready for electrical termination
-  base of cylinder to out port on regulator
+Leave cable X283 tied off in a loop on cylinder</translate>
+|Step_Picture_00=R0015087_Pneumatic_Connections_Screenshot_2023-11-22_074301.png
-In port of regulator to active port on valve bank  (4)</translate>
+|Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":511,"height":682,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1.17,"scaleY":1.17,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/e/ed/R0015087_Pneumatic_Connections_Screenshot_2023-11-22_074301.png","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":369.17,"top":298.83,"width":74.28,"height":74.28,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":37.140545968682204,"ry":37.140545968682204}],"height":801,"width":600}
+|Step_Picture_01=R0015087_Pneumatic_Connections_Screenshot_2023-12-22_075047.png
 }}
 {{Tuto Step