R0015004 Bench Assemble Gripper

Instructions to bench assemble gripper

Difficulté

Medium Moyen

Durée

2 hour(s) heure(s)

R0015004_Bench_Assemble_Gripper_Screenshot_2023-10-10_112949.png

Introduction

Tools Required

External circlip pliers

Standard Hex key set

Standard spanner set

Reed switch setting box

Hammer

Standard screwdriver set

Rule

Parts Required

B0001106 x 20

D0015095 x 8

D0015096 x 2

D0015086 x 1

B0000034 x 2

D0015084 x 2

D0015083 x 1

D0015082 x 1

E0000366L x 1

B0001182 x 2

M0001182 x 2

D0015756 x 1

P0001013 x 1

P0001041 x 1

P0001128 x 1

P0001198 x 2

P0001120 x 1

D0015431 x 1

B0000437 x 1

D0015430 x 1

D0015090 x 2

D0015085 x 1

D0015102 x 2

D0015103 x 2

D0015104 x 2

D0015170 x 2

P0000049 x 1

D0015097 x 2

D0015100 x 2

D0015292 x 1

E0000336 x 1

E0001069 x 1

A0001044 x 4

• Pièces et outils

Pièces et outils

[[Item:|]] A fatal error occurred in the #info parser function

Étape 1 - Unless otherwise stated

Use Loctite 243 on all fasteners

Pen mark all bolts once finalised

Étape 2 - Fit bushes and bearings

1 Fit bushes B0001106 (20 off) to

8 off D0015095 link bars

2 off D0015096 link bars

2 Fit bearings B0000034 x 2 into D00015086 grip slide body. Use grease to lubricate bearing before assembly

Étape 3 - check for rework

Check that part D0015082 has been manufactured to the listed details highlighted in drawing attached to this step. If M4 and M5 holes are not present, rework and record time

Étape 4 - check fitment of D0015084 shafts

Check shafts fit correctly into bores of D0015082 gripper bottom bar and D0015083 gripper upper bar

Étape 5 - Assemble load switch plate

1 Use M4 x 6 panhead to attach B0001181 rail to gripper base

Fit M0001182 spring to main base

2 Use M5x 6 x 16 shoulder bolt and M4 x 6 pan heads to attach D0015756 lever to assembly

Étape 6 - Fit Sensor

1 Add cable markers to E0001069 cable , Mark as X44 both ends

2 Attach above cable to E0000336L and fit as shown with 1 off supplied lock nut and shakeproof washer on the indicated face

3 Set Sensor position as follows

Press lever fully in direction shown

Adjust sensor to touch rear of profile present lever

Adjust sensor back half a turn

Lock of lock nut to hold position ( Do not over tension )

Check, when lever is pressed fully back, the sensor should be close to the profile present lever but not touching

Étape 7 - Fix X44 cable

Use 4 off A0001044 p clips 4 off M4 x 12 socket caps and captivate X44 cable at points shown

Étape 8 - Assemble cylinder P0001120

Fit air fitting P0001198 to cylinder

Remove 32mm nut from cylinder and discard

Mount reed switch and band (P0001041 x 1 P0001013 x 1 P0001128 x 1) to cylinder in piston retracted position , mark as X283

Picture required

Étape 9 - Assemble grip pin assembly

1 Fit bushes B0000437 x2 to body D0015431

2 Use 2 off 10mm x 40mm dowel. Ensure dowels fit correctly in nose D0015430. Check dowels have pushed all the way to the bottom of the bore . Secure with 2 off M4 x 8 grubscrew

3 Fit D0015090 Grip pin x 2 and secure with M5x 16 socket cap

4 Combine together and use m8 x 70 set bolt, a form washer and 2 x m8 half nuts to secure. Set gap to 13mm and lock all fasteners

Étape 10 - Mount grip pin assembly to grip slide

Combine parts

1 Use 2 off 6mm x 20mm dowels to align ( 1 top and 1 bottom)

2 M8 x 16 socket cap and A form washer

3 M8 x 20 countersink

Étape 11 - Assemble main frame of gripper assembly

Use 2 off D0015085

1 Assemble as shown using 8 off M8 x 20 socket caps and 4 off M6 x 12 socket caps

2 Check top and bottom bars are parallel

3 Check grip slide moves freely up and down

Étape 12 - Fit link bars to assembly

1 Use 2 off D0015103 and 8mm external circlips (B0000200) and assemble two off as shown

2 Use 2 off D0015102, 2 off D0015104 and assemble as shown with 8mm circlips

3 Use 2 off D0015170 gripper spacers and P0000049 spherical end and add as shown

4 Add remaining link shafts and circlips

Étape 13 - Fit Cylinder assembly

Fit assembled cylinder unit to gripper frame

1 Wind cylinder thread into spherical bearing lock cylinder nut off with 1 thread of cylinder piston exposed behind lock nut

2 Use M5 x 10 with a form washer to secure D0015097 2 off mounting plates

3 Use M8 x 30 with M8 nyloc nut to secure cylinder to brackets

Étape 14 - Add mounting brackets

1 Fix as shown 2 off D0015100 brackets with 4 off M10 x 40 socket caps

2 Mount Sensor bracket D0015292 with 2 off M5 x 30 socket caps, A form washers and M5 Nyloc nuts. Mount E0000336 as shown using both lock nuts and shake proof washers provided with sensor

en none 0 Draft