This page shows each of the IO Screens on an Autoflow and describes each Input/Output
On an Autoflow machining centre there are 3 IO Screens
- 1. IO
- 2. IO-Infeed
- 3. Spindle IO
each of these has a section below with a table describing each input and output.
Autoflow Main IO Screen
Autoflow Main IO Screen
Autoflow Main Inputs
Module A – Infeed Table
| Sensor | Description | Sensor | Description |
| InA_GripperOff | Gripper Slip Sensor | InA_48vOk | 48v Ok (No Errors) |
| InA_Measure1 | Offcut Measure Sensor 1 | InA_AirOk | Air Supply OK |
| InA_Measure2 | Offcut Measure Sensor 2 | InA_Grip | Gripper Sensor (Profile in place) |
| InA_GZHome | Gripper Z Axis Home | InA_EStop | Emergency Stop State |
| InA_GYHome | Gripper Y Axis Home | InA_ButStart | Start Button |
| InA_GXHome | Gripper X Axis Home | InA_ButStop | Stop Button |
| InA_MatLoad1 | Material Load Sensor 1 | InA_ButReset | ES Reset Button |
| InA_MatLoad2 | Material Load Sensor 2 | InA_ButEstop1 | Emergency Stop Button 1 |
| InA_Index | Infeed Table Index Position | InA_ButEstop2 | Emergency Stop Button 2 |
| InA_VCUOk | VCU Ok (No Errors) | InA_ButEstop3 | Emergency Stop Button 3 |
| InA_Bus415Ok | Bus415Ok (No Errors) | InA_ButAuto | Auto Load Button |
| InA_Bus415SOk | Bus415S Ok (No Errors) | InA_MatlAtFence | Material At Back Fence Sensor |
| InA_24vBusOk | 24v Bus Ok (No Errors) | InA_StopOver | Profile Stop |
| InA_24vModOk | 24v Module Ok (No Errors) | InA_ButLoad | Load Button |
Module B – Multihead
| Sensor | Description | Sensor | Description |
| InB_YHome | Y Axis Home Switch | InB_ClampOSH | Clamp Outfeed Side Home |
| InB_ZHome | Z Axis Home Switch | InB_ClampITH | Clamp Infeed Top Home |
| InB_RHome | R Axis Home Switch | InB_ClampISH | Clamp Infeed Side Home |
| InB_ClampOTH | Clamp Outfeed Top Home | InB_OilerOK | Oiler OK (No Errors) |
Module F – Saw and Outfeed
| Sensor | Description | Sensor | Description |
| InF_SYHome | Saw Y Axis Home (forward/back) | InF_EjectHm | Ejector Home |
| InF_SZHome | Saw Z Axis Home (up/down) | InF_EjectOu | Ejector Out |
| InF_SRHome | Saw R Axis Home (rotation) | InF_AdvanceB |
Saw Outfeed Advance Button |
| InF_EjPushHm | Eject Pusher Home | InF_InvSawOk | Saw Invertor OK (No Errors) |
| InF_EjPushOu | Eject Pusher Out | InF_InvExtract | Extractor Invertor OK |
| InF_ClampOTH | Clamp Outfeed Top Home | InF_ConvOvlO | Conveyor Overload |
| InF_ClampOSH | Clamp Outfeed Side Home | InF_TiltHm | Saw Blade Tilt Home (vertical) |
| InF_ClampITH | Clamp Infeed Top Home | InF_TiltOu | Saw Blade Tilt Out (tilted) |
| InF_ClampISH | Clamp Infeed Side Home | InF_GtOpen | Gate Open |
| InF_RollerITHm | Roller Infeed Top Home | InF_GtClosed | Gate Closed |
| InF_48vOk | 48v Ok (no errors) | InF_GuardFront | Front Door |
| InF_24vBusOk | 24v Bus Ok (no errors) | InF_GuardRear | Rear Door |
| InF_24vModOk | 24v Module Ok (no errors) | InF_OfFull | Outfeed Full Sensor |
| InF_ButEstop4 | Emergency Stop Button 4 |
Autoflow Main Outputs
Module A – Infeed Table
| Output | Description | Output | Description |
| OuA_CtrlOn | OuA_PopUp | Profile Stop Popup | |
| OuA_Grip | Gripper | OuA_StopX | Profile Stop In/Out |
| OuA_GripBlow | Gripper Blower | BrakesOff | Drive Brakes |
| OuA_LoadBlow | LoadBlower | OuA_GripTurn | Gripper Turned? |
Module B – Multihead
| Output | Description | Output | Description |
| OuB_ClampIT | Clamp Infeed Top | OuB_ClampOS | Clamp Outfeed Side |
| OuB_ClampIS | Clamp Infeed Side | OuB_ClampOSPos | Clamp Outfeed Side Wide Pos |
| OuB_ClampISPos | Clamp Infeed Side Wide Pos | OuB_Oiler | Oiler |
| OuB_ClampOT | Clamp Outfeed Top | OuB_OilerChn | Oiler Chain |
| OuB_ClampOTPos | Clamp Outfeed Top Tall Pos |
Module F – Saw and Outfeed
| Output | Description | Output | Description |
| OuF_ClitHi | Clamp Infeed Top High Press | OuF_Eject | Saw Ejector |
| OuF_ClampITR | Clamp Infeed Top Tall Pos | OuF_OffBlow | Outfeed Blower |
| OuF_ClampOT | Clamp Outfeed Top | OuF_Siren | Long Length Siren |
| OuF_ClampIS | Clamp Infeed Side | OuF_Gate | Long Length Safety Gate |
| OuF_ClampOS | Clamp Outfeed Side | OuF_SawOn | Saw Blade |
| OuF_EjectPush | Eject Pusher | OuF_ExtractO | Extractor |
| OuF_Conveyor | Outfeed Conveyor | OuF_ChuteBlo | Chute Blower |
Autoflow Infeed IO Screen
Autoflow Infeed IO Screen
Autoflow Infeed Inputs
| Sensor | Description | Sensor | Description | Sensor | Description |
|---|---|---|---|---|---|
| InA_Pos1On | Infeed Flapper 1 On | InA_Pos1Off | Infeed Flapper 1 Off | InA_CrankFwd | Infeed Crank Forward |
| InA_Pos2On | Infeed Flapper 2 On | InA_Pos2Off | Infeed Flapper 2 Off | InA_CrankHm | Infeed Crank Home |
| InA_Pos3On | Infeed Flapper 3 On | InA_Pos3Off | Infeed Flapper 3 Off | InA_Infeed_Ad | ? |
| InA_Pos4On | Infeed Flapper 4 On | InA_Pos4Off | Infeed Flapper 4 Off | ||
| InA_Pos5On | Infeed Flapper 5 On | InA_Pos5Off | Infeed Flapper 5 Off | ||
| InA_Pos6On | Infeed Flapper 6 On | InA_Pos6Off | Infeed Flapper 6 Off |
Autoflow Infeed Outputs
| Output | Description | Output | Description |
|---|---|---|---|
| OuA_Dog1 | ? | OuA_PopUpPu | ? |
| OuA_Dog2 | ? | OuA_PopUp | Profile Stop Popup |
| OuA_Dog3 | ? | OuA_PopUp3 | Pop Up Cylinder 3 |
| OuA_Dog4 | ? | OuA_PopUp4 | Pop Up Cylinder 4 |
| OuA_Dog5 | ? | OuA_PopUp5 | Pop Up Cylinder 5 |
| OuA_Dog6 | ? | OuA_PopUp6 | Pop Up Cylinder 6 |
| OuA_PopUp7 | Pop Up Cylinder 7 | ||
| OuA_PopUp8 | Pop Up Cylinder 8 |
Autoflow Spindle IO Screen
Autoflow Spindle IO Screen
Spindle Inputs
| Sensor | Description | Sensor | Description |
| InB_Spin1Hm | Spindle 1 Home | InB_Spin5Hm | Spindle 5 Home |
| InB_Spin1Ou | Spindle 1 Out | InB_Spin5Ou | Spindle 5 Out |
| InB_Spin1DPHm | Spindle 1 Dbl Plunge Home | InB_Spin5DPHm | Spindle 5 Dbl Plunge Home |
| InB_Spin1DPOu | Spindle 1 Dbl Plunge Out | InB_Spin5DPOu | Spindle 5 Dbl Plunge Out |
| InB_Spin2Hm | Spindle 2 Home | InB_Spin6Hm | Spindle 6 Home |
| InB_Spin2Ou | Spindle 2 Out | InB_Spin6Ou | Spindle 6 Out |
| InB_Spin2DPHm | Spindle 2 Dbl Plunge Home | InB_Spin6DPHm | Spindle 6 Dbl Plunge Home |
| InB_Spin2DPOu | Spindle 2 Dbl Plunge Out | InB_Spin6DPOu | Spindle 6 Dbl Plunge Out |
| InB_Spin3Hm | Spindle 3 Home | InB_Spin7Hm | Spindle 7 Home |
| InB_Spin3Ou | Spindle 3 Out | InB_Spin7Ou | Spindle 7 Out |
| InB_Spin4Hm | Spindle 4 Home | InB_Spin8Hm | Spindle 8 Home |
| InB_Spin4Ou | Spindle 4 Out | InB_Spin8Ou | Spindle 8 Out |
| InB_Spin4DPHm | Spindle 4 Dbl Plunge Home | InB_Spin8DPHm | Spindle 8 Dbl Plunge Home |
| InB_Spin4DPOu | Spindle 4 Dbl Plunge Out | InB_Spin8DPOu | Spindle 8 Dbl Plunge Out |
Spindle Outputs
| Output | Description | Output | Description |
| OuB_Spin1On | Spindle 1 On | OuB_Spin5On | Spindle 5 On |
| OuB_Spin1Pl | Spindle 1 Plunge | OuB_Spin5Pl | Spindle 5 Plunge |
| OuB_Spin1DP | Spindle 1 Double Plunge | OuB_Spin5DP | Spindle 5 Double Plunge |
| OuB_Spin2On | Spindle 2 On | OuB_Spin6On | Spindle 6 On |
| OuB_Spin2Pl | Spindle 2 Plunge | OuB_Spin6Pl | Spindle 6 Plunge |
| OuB_Spin2DP | Spindle 2 Double Plunge | OuB_Spin6DP | Spindle 6 Double Plunge |
| OuB_Spin3On | Spindle 3 On | OuB_Spin7On | Spindle 7 On |
| OuB_Spin3Pl | Spindle 3 Plunge | OuB_Spin7Pl | Spindle 7 Plunge |
| OuB_Spin4On | Spindle 4 On | OuB_Spin8On | Spindle 8 On |
| OuB_Spin4Pl | Spindle 4 Plunge | OuB_Spin8Pl | Spindle 8 Plunge |
| OuB_Spin4DP | Spindle 4 Double Plunge | OuB_Spin8DP | Spindle 8 Double Plunge |
To Return to the Main Page, please click WinMulti Software Operating Guide
Draft
Français
English
Deutsch
Español
Italiano
Português