| [version en cours de rédaction] | [version en cours de rédaction] |
| Ligne 49 : | Ligne 49 : | ||
|Step_Picture_01=Omron_E5CVS_PV_Shift_Virtual_temp_2.jpg | |Step_Picture_01=Omron_E5CVS_PV_Shift_Virtual_temp_2.jpg | ||
|Step_Picture_02=Omron_E5CVS_PV_Shift_Virtual_temp_3.jpg | |Step_Picture_02=Omron_E5CVS_PV_Shift_Virtual_temp_3.jpg | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Where to Measure the Welding Plate.</translate> | ||
| + | |Step_Content=<translate>Most Machine Manufactures suggest the Measuring is done by a Probe and is in Measured in the main area of the welder plate where profile is used. | ||
| + | |||
| + | Also with no Teflon fitted . | ||
| + | |||
| + | <br /></translate> | ||
| + | |Step_Picture_00=Omron_E5CVS_PV_Shift_20230901_075328_resized.jpg | ||
| + | |Step_Picture_01=Omron_E5CVS_PV_Shift_20230901_075356_resized.jpg | ||
| + | |Step_Picture_02=Omron_E5CVS_PV_Shift_20230901_075002_resized.jpg | ||
| + | |Step_Picture_03=Omron_E5CVS_PV_Shift_20230901_074951_resized.jpg | ||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
| Ligne 57 : | Ligne 69 : | ||
}} | }} | ||
{{Tuto Status | {{Tuto Status | ||
| − | |Complete= | + | |Complete=Published |
}} | }} | ||
Version du 1 septembre 2023 à 09:32
The Purpose of the PV Shift is to make the temp controller as accurate as you can to the plate temperature.
Difficulté
Facile
Durée
10 minute(s)
Sommaire
- 1 Introduction
- 2 Étape 1 - Unit Operation
- 3 Étape 2 - Checking if Input shift is ON.
- 4 Étape 3 - Adjust Shift value until Temperature at Plate is same as on Display
- 5 Étape 4 - Checking Protection button is not locked. Dip Switch P
- 6 Étape 5 - Virtual Temp Controllers - Newer Machines (SWC) 7735
- 7 Étape 6 - Where to Measure the Welding Plate.
- 8 Commentaires
Introduction
Utiliser des vêtements de protection pour les mains
Avertissement pour surface chaude
Étape 1 - Unit Operation
Using the Mode switch step through until you reach
Étape 2 - Checking if Input shift is ON.
Étape 3 - Adjust Shift value until Temperature at Plate is same as on Display
H0 = No offset. Temp at Plate =230 degrees - Display on E5CSV = 240 Degrees
L10 = - 10 degree. Temp at plate = 230 degrees - Display E5CSV = 230 Degrees
H10 = +10 degree . Temp at plate = 230 degrees - Display E5CSV = 250 Degrees
Étape 4 - Checking Protection button is not locked. Dip Switch P
Étape 5 - Virtual Temp Controllers - Newer Machines (SWC) 7735
Log in as a High level
Find on HDMI the App Temp controller
Étape 6 - Where to Measure the Welding Plate.
Most Machine Manufactures suggest the Measuring is done by a Probe and is in Measured in the main area of the welder plate where profile is used.
Also with no Teflon fitted .
Published
Français
English
Deutsch
Español
Italiano
Português