| [version en cours de rédaction] | [version en cours de rédaction] |
(Page créée avec « {{Tuto Details |Main_Picture=ZX5_-_Specialised_Settings_for_Eaton_DE_Drives_Eaton-PowerXL-DE1-250.jpg |Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image... ») |
|||
| Ligne 6 : | Ligne 6 : | ||
|Tags=ZX5, eaton, de1, Inverter | |Tags=ZX5, eaton, de1, Inverter | ||
}} | }} | ||
| − | <translate>'''<u>Infeed motor - Module A</u>''' | + | <translate>= ZX5 Motors = |
| + | '''<u>Infeed motor - Module A</u>''' | ||
| − | * Accel = 0.1s | + | *Accel = 0.1s |
| − | * Decel = 0.1s | + | *Decel = 0.1s |
'''<u>Crank C - Module C</u>''' | '''<u>Crank C - Module C</u>''' | ||
| − | * Accel = 0.5s | + | *Accel = 0.5s |
| − | * Decel = 0.1s | + | *Decel = 0.1s |
'''<u>Crank D - Module C</u>''' | '''<u>Crank D - Module C</u>''' | ||
| − | * Accel = 1.0s | + | *Accel = 1.0s |
| − | * Decel = 0.2s | + | *Decel = 0.2s |
'''<u>Crank E - Module E</u>''' | '''<u>Crank E - Module E</u>''' | ||
| − | * Accel = 0.5s | + | *Accel = 0.5s |
| − | * Decel = 0.1s</translate> | + | *Decel = 0.1s |
| + | |||
| + | |||
| + | '''<u>Crank E - Module E</u>''' | ||
| + | |||
| + | *Accel = 0.5s | ||
| + | *Decel = 0.1s | ||
| + | |||
| + | = Autoflow Mk4 Parameters = | ||
| + | '''<u>Infeed motor - Module A</u>''' | ||
| + | |||
| + | *Accel = 0.2s | ||
| + | *Decel = 0.2s</translate> | ||
{{PageLang | {{PageLang | ||
| + | |Language=en | ||
|SourceLanguage=none | |SourceLanguage=none | ||
|IsTranslation=0 | |IsTranslation=0 | ||
| − | |||
}} | }} | ||
{{AddComments}} | {{AddComments}} | ||
Version du 25 janvier 2023 à 12:22
This page lays out the settings needed for each individual Eaton drive on a ZX5. It is important to use these settings to stop slim profiles toppling over on the transfer table
ZX5 Motors
Infeed motor - Module A
- Accel = 0.1s
- Decel = 0.1s
Crank C - Module C
- Accel = 0.5s
- Decel = 0.1s
Crank D - Module C
- Accel = 1.0s
- Decel = 0.2s
Crank E - Module E
- Accel = 0.5s
- Decel = 0.1s
Crank E - Module E
- Accel = 0.5s
- Decel = 0.1s
Autoflow Mk4 Parameters
Infeed motor - Module A
- Accel = 0.2s
- Decel = 0.2s
Draft
Français
English
Deutsch
Español
Italiano
Português