Flowline 6 to 6o5m Extension : Différence entre versions

[version en cours de rédaction][version en cours de rédaction]
(Page créée avec « {{Tuto Details |Description=<translate>Procedure for increasing flowline capacity from 6 to 6.5m</translate> |Categories=Maintenance |Difficulty=Hard |Duration=3 |Duration... »)
 
Ligne 21 : Ligne 21 :
 
{{Tuto Step
 
{{Tuto Step
 
|Step_Title=<translate>Remove Guarding</translate>
 
|Step_Title=<translate>Remove Guarding</translate>
|Step_Content=<translate></translate>
+
|Step_Content=<translate>Isolate power to extraction motor and disconnect cable, remove floor bolt nuts from feet and separate ducting so that extraction unit can be moved.
 +
 
 +
 
 +
Once moved, disconnect all guarding to the far end of multi outfeed and saw infeed (pictured).
 +
 
 +
 
 +
Remove rear guarding support box section beam.</translate>
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_1.jpg
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_1.jpg
 
}}
 
}}
 
{{Tuto Step
 
{{Tuto Step
|Step_Title=<translate></translate>
+
|Step_Title=<translate>Replacing Journals and covers</translate>
 
|Step_Content=<translate></translate>
 
|Step_Content=<translate></translate>
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_2.jpg
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_2.jpg
 
}}
 
}}
 
{{Tuto Step
 
{{Tuto Step
|Step_Title=<translate></translate>
+
|Step_Title=<translate>Remove Hepco rails</translate>
|Step_Content=<translate></translate>
+
|Step_Content=<translate>Remove both SX and X axis rear limit stops, then detach both Hepco rails by removing the 6mm caphead bolts (pictured).
 +
 
 +
 
 +
Once rails are removed, they can be separated into shorter lengths by knocking out the dowel pins towards the centre sections.</translate>
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_3.jpg
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_3.jpg
 
}}
 
}}
 
{{Tuto Step
 
{{Tuto Step
|Step_Title=<translate></translate>
+
|Step_Title=<translate>Prepare Hepco support base surface</translate>
|Step_Content=<translate></translate>
+
|Step_Content=<translate>Clean and remove any dirt/grease/imperfections on the box section ready the the new rails.
 +
 
 +
 
 +
If any of the tapped holes are compromised, re-tap 6mm.</translate>
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_4.jpg
 
|Step_Picture_00=Flowline_6_to_6o5m_Extension_4.jpg
 
}}
 
}}
Ligne 126 : Ligne 138 :
 
{{Notes}}
 
{{Notes}}
 
{{PageLang
 
{{PageLang
 +
|Language=en
 
|SourceLanguage=none
 
|SourceLanguage=none
 
|IsTranslation=0
 
|IsTranslation=0
|Language=en
 
 
}}
 
}}
 
{{Tuto Status
 
{{Tuto Status
 
|Complete=Draft
 
|Complete=Draft
 
}}
 
}}

Version du 27 janvier 2022 à 18:47

Auteur avatarGareth Green | Dernière modification 30/03/2022 par Gareth Green en cours de rédaction

Introduction

This procedure describes how to upgrade a flowline to increase the standard capacity from 6.0m to 6.5m.

The procedure involves extending the machining centre outfeed travel and saw infeed travel base to 6.0m to cope with a longer rail on each side. These are generally supplied as a new part.

Other ancillary parts that will need extending

  • Cables
  • Energy Chains

Étape 1 - Remove Guarding

Isolate power to extraction motor and disconnect cable, remove floor bolt nuts from feet and separate ducting so that extraction unit can be moved.


Once moved, disconnect all guarding to the far end of multi outfeed and saw infeed (pictured).


Remove rear guarding support box section beam.



Étape 2 - Replacing Journals and covers



Étape 3 - Remove Hepco rails

Remove both SX and X axis rear limit stops, then detach both Hepco rails by removing the 6mm caphead bolts (pictured).


Once rails are removed, they can be separated into shorter lengths by knocking out the dowel pins towards the centre sections.



Étape 4 - Prepare Hepco support base surface

Clean and remove any dirt/grease/imperfections on the box section ready the the new rails.


If any of the tapped holes are compromised, re-tap 6mm.



Étape 5 -



Étape 6 -



Étape 7 -



Étape 8 -



Étape 9 -



Étape 10 -



Étape 11 -



Étape 12 -



Étape 13 -



Étape 14 -



Étape 15 -



Étape 16 -



Étape 17 -



Étape 18 -



Étape 19 -



Étape 20 -



Étape 21 -



Commentaires

Draft