[version en cours de rédaction] | [version en cours de rédaction] |
m (Gareth Green a déplacé la page Stage 2 spindle assembly vers R000718E Stage 2 spindle assembly) |
|
(Aucune différence)
|
2nd stage of assembly of spindle assemblies
Auteur Gareth Green | Dernière modification 20/03/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽
2nd stage of assembly of spindle assemblies
Stage_2_spindle_assembly_Screenshot_47.png
Tools Required
0.05mm feeler gauge
Standard hex key set
Standard spanner set
Rule
6mm punch
Ball pien hammer
Parts Required
D0007790 cylinder anchor x 7
D0007648 end plate x 4
D0007649 Double slide end plate x 4
D0007686 single motor plate x 4
D0007723 Double slide motor mount x 4
D0007687 Motor mount x 4
D0007600 Cylinder anchor x 4
D0015856 hard stop x 4
Do not add final tension to bolts until alignment has been achieved
1 Attach pre built cylinder anchor to end of cylinder
2 Position pre built cylinder on slide base assembly as shown
3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base
4 Temporarily mount D0007648 with 1 off m6 x 20 socket cap
5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps
6 Attach Cylinder base to anchor with 4 off M6x 20 socket caps
1 Use cylinder stroke adjustment to align these two faces
2 Apply Loctite 243 to cylinder nut and tighten
3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke
4 Finalise bolts
Repeat on all four single spindles (2,4,6 and 8)
Do not add final tension to bolts until alignment has been achieved
1 Attach pre built cylinder anchor to end of cylinder
2 Position pre built cylinder on slide base assembly as shown
3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base
4 Temporarily mount D0007649 with 1 off m6 x 20 socket cap
5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps
6 Attach Cylinder base to anchor with 4 off M6x 20 socket caps
1 Use cylinder stroke adjustment to align these two faces
2 Apply Loctite 243 to cylinder nut and tighten
3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke
4 Finalise bolts
Repeat on all four single spindles (1,3,5 and 7))
4 off
1 Attach D0007686 motor plate to elte motor using 4 off m6 x 12 socket caps and 2 off 6mmx 20 dowels
2 Attach to single spindle using 4 off m6 x 20 socket caps
Ensure that motor plate butts up to indicated parts and also register is aligned as shown
3 use 5 off m6 x 20 socket caps used to finalise end plate . ensure mounting is even to motor plate
4 off
1 Lightly Fix D0007723 motor mount to bearings as shown . Use 8 off M6 x 12 socket caps to fix.
2 Use 0.05mm feeler gauge to check datum faces are in contact, if not remove and inspect parts
3 Finalise bolts
4 off
1 Mount D0007687 motor plate to elte motor with 4 off M6 x 12 socket caps and 2 off 6mm x 20 dowels
2 Use 3 off M6 x 30 socket caps and mount elte motor as shown
4 off
1 Attach D0007600 cylinder mount using 2 off M5 x 20 socket caps
2 Attach lighty pre built cylinder assembly using 4 off M6 x 20 socket caps
3 Attach cylinder thread and adjust stroke of cylinder to achieve measurement of 28mm
4 Adhesive and lock off cylinder nut
5 Use clearance in indicated holes to achieve correct cylinder alignment . Stroke of cylinder should be free and consistent
6 Finalise all bolts
1 Use M5 x 16 socket caps to mount 4 off D00015856 hard stops to double plunge assemblies
2 Use 8 off m4x 12 socket caps and fix to all slide bases as a hard stop
en none 0 Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #