| [version en cours de rédaction] | [version en cours de rédaction] |
| Ligne 106 : | Ligne 106 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate>Set IP for the Customers network</translate> | + | |Step_Title=<translate>Set the IP Address for the Customers network</translate> |
| − | |Step_Content=<translate></translate> | + | |Step_Content=<translate>Within BCP chose "Paramter Settings" |
| + | |||
| + | Select the LAN tab | ||
| + | |||
| + | enable TCP/IP | ||
| + | |||
| + | Enable Wired LAN | ||
| + | |||
| + | Set IP Address and Sub Net Mask | ||
| + | |||
| + | Press the Set Parameter at the bottom. | ||
| + | |||
| + | <br /></translate> | ||
| + | |Step_Picture_00=Toshiba_-_B-EX4T1_Printer_Setup_Screenshot_2023-02-06_150202.png | ||
| + | |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1404,"height":976,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.43,"scaleY":0.43,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/6/6b/Toshiba_-_B-EX4T1_Printer_Setup_Screenshot_2023-02-06_150202.png","filters":[]},{"type":"wfellipse","version":"2.4.6","originX":"center","originY":"center","left":34.1,"top":131.61,"width":64.34,"height":64.34,"fill":"rgba(255,0,0,0)","stroke":"#FF0000","strokeWidth":2,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"rx":32.17048299585881,"ry":32.17048299585881}],"height":417,"width":600} | ||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version du 6 février 2023 à 17:03
B-EX4T1 Printer Setup for Auto Labeling
Difficulté
Facile
Durée
20 minute(s)
Sommaire
- 1 Étape 1 - Inner & Outter
- 2 Étape 2 - Rewind Spool
- 3 Étape 3 - Printhead access
- 4 Étape 4 - Setting Rewinder
- 5 Étape 5 - Label Guides
- 6 Étape 6 - Sensor Position
- 7 Étape 7 - Closing Label Head
- 8 Étape 8 - Connecting printer to PC
- 9 Étape 9 - Initial Power up
- 10 Étape 10 - Using BCP to setup the printer
- 11 Étape 11 - Change Settings
- 12 Étape 12 - Testng
- 13 Étape 13 - Set the IP Address for the Customers network
- 14 Commentaires
Étape 1 - Inner & Outter
The instructions for the both Inner & Outter wound labels are on the inside of the open lid.
Étape 2 - Rewind Spool
There will be no ribbon and as the seetings will be for Peel Off a length of blank backing needs to be feed onto the Rewind spool
Étape 3 - Printhead access
To gain access turn the green knob to FREE. You can then pull the front plate down and lift the printer head up.
Étape 4 - Setting Rewinder
Ensure the Switch is set to REWINDER
Étape 5 - Label Guides
With the Printhead open ensure that the labels are under the small black sprung guids. Slide the green gluide to the width of the label.
Étape 6 - Sensor Position
Ensure that the send head is in the middle of the label
Étape 7 - Closing Label Head
When Loaded close the Printhead down, lift the front plate up and turn the green knob to LABEL.
Étape 8 - Connecting printer to PC
For easy setup use a USB cable (Everything can be done via the network web interface)
1) Connect a USB cable to the PC
2) Connect a Network cable to a live DHCP network to obtain an Ip address.
3) Download load the BCP setup software: https://www.toshibatec.com/download_overseas/printer/setting_tool/BCP_Series/ [1]
Étape 9 - Initial Power up
If the labels have been fitted properly on power up the calibration process will eject several labels.
Take a note of the IP addres given to the printer on the front panel.
Étape 10 - Using BCP to setup the printer
When you start BCP you should see.
Select USB if not Selected
Étape 11 - Change Settings
Press the Emulation Button and take the top option "Zmode System Parameters Settings"
Then Make the changes
- Label Length 38mm (after calibration this will be reset to 41.3)
- Label Width 98mm
- Ribbon WITHOUT RIBBON
- Print mode PEEL OFF
- Sendor TRANS PREPRINT
- Max Label Length (for callabration) 200mm (this just saves on the callorbration)
Press the DOWNLOAD button and check that there are no errors.
Étape 12 - Testng
1) Pressing Feed should push out another label regards.
2) Send a lable to the printer via the network (or via the Test - Send file within BCP).
3) Send more that one file and make sure that eah time you remove a label fomr the output the ext one is presented.
Étape 13 - Set the IP Address for the Customers network
Within BCP chose "Paramter Settings"
Select the LAN tab
enable TCP/IP
Enable Wired LAN
Set IP Address and Sub Net Mask
Press the Set Parameter at the bottom.
Draft
Français
English
Deutsch
Español
Italiano
Português