R0015146 Pneumatic pipe Installation

Details to install pneumatic loom

Difficulté

Hard Difficile

Durée

8 hour(s) heure(s)

R0015336_Pneumatic_Output_Testing_Screenshot_2023-10-23_135339.png

Introduction

Tools Required

Pipe cutters

Pipe identification markers

Flush cutters

Parts Required

P0000046 Fitting: 'Y' Adaptor 6mm x 6

P0000047 Bulkhead Elbow 6mm x 1

P0000159 Fitting: Stem Blanking Plug 6mm x 2

P0000160 Fitting: Flow Controller In Line 6mm x 2

P0000551 6mm inline Quick Exhaust Fitting x 3

P0001030 Fitting: SMC 6mm Equal Tee x 1

P0001106 Plug in reducer 12-8mm x 1

P0001107 Fitting 12mm equal tee x 1

P0001166 12mm tube to tube elbow x 1

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Valve bank identification

2 row is home position

4 row is active

Étape 3 - Y80 Infeed top clamp

801 valve bank home to cylinder nose

809 valve bank active Y to feed Y80 regulator in and port indicated on picture

802 Regulator out to feed port indicated on picture

803 to feed cylinder rear port and valve port indicated . P0000551 to be fitted to this line next to cylinder

Étape 4 - Y82 Outfeed top clamp

821 from Valve bank home to cylinder nose

829 from valve bank active to cylinder rear

Étape 5 - Y91 Eject

911 from valve bank home to cylinder nose

919 from valve bank active to cylinder rear

Étape 6 - Y202 side clamp

2021 from valve bank home to cylinder rear

2029 from valve bank active to regulator in

2022 from regulator out to cylinder nose.

Add P0000551 to 2022 close to cylinder

ensure pipe loom does not foul any areas when movement of assemblies occurs

Étape 7 - Y204 Clamp position

2041 from valve bank home to in on p0000160 flow regulator then out, Y connection then feeds to nose of both cylinders

2049 from valve bank active to in on p0000160 flow regulator then out, Y connection then feeds to rear of both cylinders

Étape 8 - Y206 centralise

2061 from valve bank home to nose of cylinder

2069 from valve bank active to regulator in

2062 from regulator out to base of cylinder

fit P0000551 QEV to 2062 close to cylinder

ensure pipe loom does not foul any areas when movement of assemblies occurs

Étape 9 - Y207 saw cut

2071 from valve bank home to nose of cylinder

2079 from valve bank active to rear of cylinder

Flow restriction fitted next to cylinder fitting on rear

Étape 10 - Y210 Z support infeed

2101 from valve bank home to nose of cylinder

2109 from valve bank active to rear of cylinder

Étape 11 - Y213 Saw blowers

2139 from valve bank active to feed saw chute blower, turntable blower and conveyor blower.

P0000160 to be fitted on turntable and chute blowers .

Split feeds with y fittings

Étape 12 - Y214 Z Turret infeed

2149 from active port on valve bank to feed on infeed turret

Étape 13 - Y215 Z Turret outfeed

2159 from active port on valve bank to feed on outfeed turret

Étape 14 - Y224 Outfeed Z block

2241 from home port on valve bank to nose of cylinder

2249 from active port on valve bank to rear of cylinder

en none 0 Draft