R0015266B mount completed assemblies : Différence entre versions

[version en cours de rédaction]

Version du 17 août 2023 à 14:12

Instructions to mount pre built assemblies to frame

Auteur Gareth Green | Dernière modification 10/01/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Moyen

Durée

2 heure(s)

Instructions to mount pre built assemblies to frame

Difficulté

Moyen

Durée

2 heure(s)

Introduction

Tools Required

Standard hex key set

Parts Required

D0015432 Spacer: Ø25.4 x 100mm (12.7mm ID) x 10

D0015479 Sensor Mount Rail 1450 mm Long x 4

D0015480 Sensor Mount Rail 825 Long x 1

F0000299 T Nut Sub Insert M6 (Fat) x 16

R0015030B Bench Assembly Loader Wheel

R0015080 Bench assemble sensor rail

R0015271 Mount buffer bars ( pre fitted to frame )

R0015351 Mount monitor to frame (pre fitted to frame)

Étape 1 - Unless otherwise stated

Use loctite 243 on all fasteners

Use Loctite 572 on all threaded pneumatic connections

Pen mark all bolts to show finalised

R0015086 Assemble Pneumatics on to electrical cabinet loctite 243.png

Étape 2 - Attach sensor rail 1

Use M10 x 120 socket caps to secure sensor rail parts to frame

Attach D0015480 Sensor Mount Rail 825 Long with 2 off D0015432 Spacer: Ø25.4 x 100mm (12.7mm ID)

Étape 3 - Attach sensor rails

Use M10 x 120 socket caps to secure sensor rail parts to frame

Attach 4 off D0015479 Sensor Mount Rail 1450 mm Long with 8 off D0015432 Spacer: Ø25.4 x 100mm (12.7mm ID)

Étape 4 - Mount sensors

Mount sensors from assembly R0015080 with F0000299 M6 D nuts and M6 x 12 socket caps with A form washers

Use Drawing shown for positions , and images for orientation

Ensure drawing is followed for positions of sensors. These measurements are to set the sensors in a standard position. Commission team may alter these on test, but for production adhere to measurements given

Étape 5 - Mount Loader wheel assembly

Mount loader wheel assemble to frame Using M10 x 30 socket caps with large M10 penny washers (40mm diameter)

Quality check

1 When loader wheel pulley is in its lowest position it must not hit the sensor rail assembly. If contact is evident follow step 2

2 Use Washers as spacers ( size required ) to lift the assembly up from the frame mounting point and create clearance between the loader wheel and the sensor rail

Commentaires

en none 0 Draft

@@ Ligne 67 : / Ligne 67 : @@
-Use Drawing shown for positions , and images for orientation</translate>
+Use Drawing shown for positions , and images for orientation
+Ensure drawing is followed for positions of sensors.  These measurements are to set the sensors in a standard position.  Commission team may alter these on test, but for production adhere to measurements given</translate>
 |Step_Picture_00=R0015266B_mount_completed_assemblies_large-1000004904.jpg
 |Step_Picture_00_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":0,"top":0,"width":1280,"height":577,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.47,"scaleY":0.47,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/d/d8/R0015266B_mount_completed_assemblies_large-1000004904.jpg","filters":[]}],"height":270,"width":600}
@@ Ligne 79 : / Ligne 81 : @@
 {{Tuto Step
 |Step_Title=<translate>Mount Loader wheel assembly</translate>
-|Step_Content=<translate>Mount loader wheel assemble to frame Using socket caps  (size required)
+|Step_Content=<translate>Mount loader wheel assemble to frame Using M10 x 30 socket caps with large M10 penny washers (40mm diameter)