Flowline 6 to 6o5m Extension : Différence entre versions

[version en cours de rédaction]

Version du 27 janvier 2022 à 18:44

Procedure for increasing flowline capacity from 6 to 6.5m

Auteur Gareth Green | Dernière modification 30/03/2022 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Pas encore d'image

Difficulté

Difficile

Durée

3 jour(s)

Procedure for increasing flowline capacity from 6 to 6.5m

6.5m, Extension, Upgrade

Introduction

This procedure describes how to upgrade a flowline to increase the standard capacity from 6.0m to 6.5m.

The procedure involves extending the machining centre outfeed travel and saw infeed travel base to 6.0m to cope with a longer rail on each side. These are generally supplied as a new part.

Other ancillary parts that will need extending

Cables
Energy Chains

Étape 1 - Remove Guarding

Isolate power to extraction motor and disconnect cable, remove floor bolt nuts from feet and separate ducting so that extraction unit can be moved.

Once moved, disconnect all guarding to the far end of multi outfeed and saw infeed (pictured).

Detach Outfeed beam sensor with bracket so that rear guarding support box section can be removed.

Étape 2 - Removing carriages and replacing Journals

Remove both rear limit stops blocks, then disconnect all energy chain cables and air pipes at the carriage ends of the X and SX axis,

Unclip the energy chain and remove both carriages.

On a bench, remove Gearbox/motor assembly's and replace the pinion gears (small amount of Loctite on grubscrew).

Now remove all x6 journals and x6 covers and disregard. Now fit:

x3 Concentric Journals - These must be fitted on the TEETH SIDE of the Hepco rail.

x3 Eccentric Journals - Fit on the opposite side and LEAVE LOOSE for now.

Leave the Journal covers off for now.

Étape 3 - Remove Hepco rails

Detach both Hepco rails by removing the 6mm caphead bolts (pictured).

Once rails are removed, they can be separated into shorter lengths by knocking out the dowel pins towards the centre sections.

Étape 4 - Prepare Hepco support base surface

Clean and remove any dirt/grease/imperfections on the box section ready the the new rails.

If any of the tapped holes are compromised, re-tap 6mm.

Étape 5 - Drilling Extension Pieces

Étape 6 -

Étape 7 -

Étape 8 -

Étape 9 -

Étape 10 -

Étape 11 -

Étape 12 -

Étape 13 -

Étape 14 -

Étape 15 -

Étape 16 -

Étape 17 -

Étape 18 -

Étape 19 -

Étape 20 -

Étape 21 -

Commentaires

en none 0 Draft

@@ Ligne 71 : / Ligne 71 : @@
 |Step_Content=<translate></translate>
 |Step_Picture_00=Flowline_6_to_6o5m_Extension_5.jpg
-|Step_Picture_01=Flowline_6_to_6o5m_Extension_6.jpg.jpg
-|Step_Picture_01_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-9,"top":-596,"width":2322,"height":4128,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.27,"scaleY":0.27,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/b/b3/Flowline_6_to_6o5m_Extension_6.jpg.jpg","filters":[]},{"type":"wfnumberedbullet","version":"2.4.6","originX":"left","originY":"top","left":314,"top":152.96,"width":25,"height":25,"fill":"rgb(0,0,0)","stroke":"#FF0000","strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"objects":[{"type":"circle","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":24,"height":24,"fill":"#FF0000","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"radius":12,"startAngle":0,"endAngle":6.283185307179586},{"type":"text","version":"2.4.6","originX":"center","originY":"center","left":0,"top":0,"width":7.79,"height":15.82,"fill":"rgba(255,255,255,255)","stroke":null,"strokeWidth":1,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":1,"scaleY":1,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"text":"2","fontSize":14,"fontWeight":"normal","fontFamily":"arial","fontStyle":"normal","lineHeight":1.16,"underline":false,"overline":false,"linethrough":false,"textAlign":"left","textBackgroundColor":"","charSpacing":0,"styles":{} }],"number":2}],"height":449.438202247191,"width":600}
 }}
 {{Tuto Step