Setting Ultrasonic Sensor - Vertical : Différence entre versions

[version en cours de rédaction]

Version actuelle datée du 31 mars 2020 à 14:42

How to set ultrasonic sensor to detect profile

Auteur Gareth Green | Dernière modification 31/03/2020 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽

Difficulté

Facile

Durée

2 minute(s)

How to set ultrasonic sensor to detect profile

Difficulté

Facile

Durée

2 minute(s)

Sommaire

1 Introduction
2 Video d'introduction
3 Étape 1 - Ensure there is 30mm clearance from sensor to profile
4 Étape 2 - Press button with profile in place
5 Étape 3 - Press Button with profile removed
6 Étape 4 - Check that it works
7 Commentaires

ultrasonic, sensor, infeed, setting

Introduction

How to set up an ultrasonic sensor when it is mounted vertically. This is normally the case on ZX5 machines on the "Mod_Clear" functions near the rollers.

Video d'introduction

Vimeo

Étape 1 - Ensure there is 30mm clearance from sensor to profile

If the sensor is closer than 30mm, it will not work

Setting Ultrasonic Sensor on infeed Table Ultra 0.JPG

Étape 2 - Press button with profile in place

Hold button in until yellow and green lights flash, let go

Étape 3 - Press Button with profile removed

This sets the longest range of the sensor.

Hold until flashing stops

Étape 4 - Check that it works

Light will come on when object is detected

Commentaires

en none 0 Draft

@@ Ligne 10 : / Ligne 10 : @@
 }}
 {{Introduction
-|Introduction=<translate>How to set up an ultrasonic sensor when it is mounted vertically. This is normally the case on ZX5 machines on the "Mod_Clear" functions near the rollers.<syntaxhighlight>
+|Introduction=<translate>How to set up an ultrasonic sensor when it is mounted vertically. This is normally the case on ZX5 machines on the "Mod_Clear" functions near the rollers.
-gaps  | SQ  \ MI  < AH  / IM  e ES  s mSQ m mMI a mAH i mIM f YF  r YR (Lead)
-| SQ  k     j+v   w+j   j+v   t     k     j+v   w+j   j+v   k     k
+<br /></translate>
-\ MI  j+v   j+v   w+j   j+v   t     j+v   j+v   w+j+v j+v   j+v   j+v
-> AH  k+x   j+v   j     j+v   t     k+x   j+v  	j     j+v   k+x   k+x
-/ IM  j+v   j+v   w+j+v j+v   t     j+v   j+v   w+j+v j+v   j+v   j+v
-e ES  k     j     j     j     0     s     s     s     s     s+s   s+s
-s mSQ k     j+v   w+j   j+v   e     k     j+v   w+j   j+v   k     k
-m mMI j+v   j+v   w+j   j+v   e     j+v   j+v   w+j+v j+v   j+v   j+v
-a mAH k+x   j+v   j     j+v   e     k+x   j+v  	j     j+v   k+x   k+x
-i mIM j+v   j+v   w+j+v j+v   e     j+v   j+v   w+j+v j+v   j+v   j+v
-f YF  k     j+v   w+j   j+v   e     k     j+v   w+j   j+v   k     f
-r YR  k     j+v   w+j   j+v   e     k     j+v   w+j   j+v   f     k
-for version 6.63
-Y notches on Ring only
-</syntaxhighlight><br /></translate>
 }}
 {{TutoVideo
@@ Ligne 32 : / Ligne 19 : @@
 }}
 {{Materials}}
-{{EPI
+{{EPI}}
-|EPI=use-footbridge
-}}
 {{Tuto Step
 |Step_Title=<translate>Ensure there is 30mm clearance from sensor to profile</translate>