| [version en cours de rédaction] | [version en cours de rédaction] |
| Ligne 16 : | Ligne 16 : | ||
{{Tuto Step | {{Tuto Step | ||
|Step_Title=<translate>Ensure the area is clear</translate> | |Step_Title=<translate>Ensure the area is clear</translate> | ||
| + | |Step_Content=<translate></translate> | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Mark floor area out roughly with marker pen</translate> | ||
| + | |Step_Content=<translate></translate> | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Position M/C and level up</translate> | ||
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
}} | }} | ||
| Ligne 43 : | Ligne 51 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate> | + | |Step_Title=<translate>Fit Transfer Gate (between MH and Saw)</translate> |
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
}} | }} | ||
| Ligne 61 : | Ligne 69 : | ||
|Step_Title=<translate>Fit Conveyor</translate> | |Step_Title=<translate>Fit Conveyor</translate> | ||
|Step_Content=<translate></translate> | |Step_Content=<translate></translate> | ||
| + | }} | ||
| + | {{Tuto Step | ||
| + | |Step_Title=<translate>Fit Extraction Piping and Extraction Gates</translate> | ||
| + | |Step_Content=<translate>No hard pipe under the Saw.</translate> | ||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version du 29 novembre 2019 à 11:50
Correct procedure for ZX5 Installation
Difficulté
Très difficile
Durée
5 jour(s)
Sommaire
- 1 Introduction
- 2 Étape 1 - Ensure the area is clear
- 3 Étape 2 - Mark floor area out roughly with marker pen
- 4 Étape 3 - Position M/C and level up
- 5 Étape 4 - Position transfer tables in relation to floor plan
- 6 Étape 5 - Level machining centre outfeed frame
- 7 Étape 6 - Square up and level Saw infeed
- 8 Étape 7 - Position Extraction Unit
- 9 Étape 8 - Position transfer arms
- 10 Étape 9 - Adjust height of Saw Infeed to be level with M/C Outfeed
- 11 Étape 10 - Fit Transfer Gate (between MH and Saw)
- 12 Étape 11 - Position M/C Infeed and level up
- 13 Étape 12 - Position Sawing Module and level up
- 14 Étape 13 - Position Saw Outfeed and level up
- 15 Étape 14 - Fit Conveyor
- 16 Étape 15 - Fit Extraction Piping and Extraction Gates
- 17 Commentaires
Introduction
Utiliser des chaussures de protection
Porter des vêtements de protection
Utiliser un casque protecteur
Utiliser un gilet réfléchissant
Pour l'entretien, débranchez l'appareil du secteur
Étape 1 - Ensure the area is clear
Étape 2 - Mark floor area out roughly with marker pen
Étape 3 - Position M/C and level up
Étape 4 - Position transfer tables in relation to floor plan
Étape 5 - Level machining centre outfeed frame
Étape 6 - Square up and level Saw infeed
Measure up diagonals
Étape 7 - Position Extraction Unit
Étape 8 - Position transfer arms
Étape 9 - Adjust height of Saw Infeed to be level with M/C Outfeed
Étape 10 - Fit Transfer Gate (between MH and Saw)
Étape 11 - Position M/C Infeed and level up
Étape 12 - Position Sawing Module and level up
Étape 13 - Position Saw Outfeed and level up
Étape 14 - Fit Conveyor
Étape 15 - Fit Extraction Piping and Extraction Gates
No hard pipe under the Saw.
Draft
Français
English
Deutsch
Español
Italiano
Português