|
|
| Ligne 9 : |
Ligne 9 : |
| | }} | | }} |
| | {{Introduction | | {{Introduction |
| − | |Introduction=<translate><u>'''Tools Required'''</u> | + | |Introduction=<translate>19/09/2025 |
| | | | |
| | | | |
| − | standard hex key set
| + | Moved to Confluance |
| | | | |
| − | Pipe Cutters
| |
| | | | |
| − | Wire basket cutting tools
| + | Click [https://stuga-ltd.atlassian.net/wiki/external/MGRmNThkNzU1OGUwNDlkY2FiYTU0NTFhYjY3NDFlYTg Here]</translate> |
| − | | |
| − | | |
| − | <u>'''Parts Required'''</u>
| |
| − | | |
| − | | |
| − | A0001061 Retainer: Wire Basket Cable Tray x 2
| |
| − | | |
| − | A0001065 Wire cable tray 3m length x 1
| |
| − | | |
| − | <br /></translate>
| |
| | }} | | }} |
| | {{Materials}} | | {{Materials}} |
| | {{EPI}} | | {{EPI}} |
| | {{Tuto Step | | {{Tuto Step |
| − | |Step_Title=<translate>Unless otherwise stated</translate> | + | |Step_Title=<translate></translate> |
| − | |Step_Content=<translate>Use Loctite 243 on all fasteners | + | |Step_Content=<translate></translate> |
| − | | |
| − | Use Loctite 572 on all threaded pneumatic connection
| |
| − | | |
| − | Pen mark all fasteners to show finalised</translate>
| |
| − | |Step_Picture_00=R0015086_Assemble_Pneumatics_on_to_electrical_cabinet_loctite_243.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Cut wire basket</translate>
| |
| − | |Step_Content=<translate>Cut a length of wire basket to 1600mm</translate>
| |
| − | |Step_Picture_00=R0015294_Fitment_of_wire_basket_and_feed_pipes_Screenshot_2023-10-30_154825.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Fix basket to supports</translate>
| |
| − | |Step_Content=<translate>Fix basket using 2 off brackets as shown
| |
| − | | |
| − | Use M6 x 20 socket caps, M6 motor plate washers and M6 d nuts to fix
| |
| − | | |
| − | | |
| − | Fit wire basket to be closest to front of transfer table
| |
| − | | |
| − | | |
| − | Ensure wire basket is centralised between brackets</translate>
| |
| − | |Step_Picture_00=R0015294_Fitment_of_wire_basket_and_feed_pipes_Screenshot_2023-10-30_154936.png
| |
| − | |Step_Picture_01=R0015294_Fitment_of_wire_basket_and_feed_pipes_Screenshot_2023-10-30_155018.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>12mm blue pipe fitted in error</translate>
| |
| − | |Step_Content=<translate>Do not fit 12mm blue airpipe . This is incorrect and not required. Please capture pictures of only red pipes fitted to wire basket please</translate>
| |
| − | |Step_Picture_00=ZX5_Production_R0015122_Module_A_to_R0015139_Module_B_alignment_photorequired.png
| |
| − | }}
| |
| − | {{Tuto Step
| |
| − | |Step_Title=<translate>Add 2 off red 12mm lines</translate>
| |
| − | |Step_Content=<translate>cut 2 off 12mm red airpipes @ <u>4500mm</u>
| |
| − | | |
| − | | |
| − | Fix to indicated section of wire basket, leaving equal overhang of pipe either end</translate>
| |
| − | |Step_Picture_00=R0015294_Fitment_of_wire_basket_and_feed_pipes_Screenshot_2023-10-30_155159.png
| |
| | }} | | }} |
| | {{Notes}} | | {{Notes}} |
Français
English
Deutsch
Español
Italiano
Português