| [version en cours de rédaction] | [version en cours de rédaction] |
| (4 révisions intermédiaires par le même utilisateur non affichées) | |||
| Ligne 5 : | Ligne 5 : | ||
|Categories=Production | |Categories=Production | ||
|Difficulty=Medium | |Difficulty=Medium | ||
| − | |Duration= | + | |Duration=1 |
|Duration-type=hour(s) | |Duration-type=hour(s) | ||
}} | }} | ||
{{Introduction | {{Introduction | ||
| − | |Introduction=<translate>'''<u>Tools Required</u>''' | + | |Introduction=<translate>'''<u>Tools Required</u>''' |
| − | '''<u>Parts Required</u>'''</translate> | + | Standard spanner set |
| + | |||
| + | |||
| + | '''<u>Parts Required</u>''' | ||
| + | |||
| + | Pre built Slide units</translate> | ||
}} | }} | ||
{{Materials}} | {{Materials}} | ||
| Ligne 33 : | Ligne 38 : | ||
| − | 2 | + | 2 Use setting dokit [[Setting Delrin Transfer Table Wheel Tension]] and set delrin wheels to correct tension. Check at all points over oozenest V rail |
| + | |||
| + | 3 Repeat for all 9 units</translate> | ||
|Step_Picture_00=R0015094_Fit_Slider_units_Screenshot_2023-06-13_100406.png | |Step_Picture_00=R0015094_Fit_Slider_units_Screenshot_2023-06-13_100406.png | ||
|Step_Picture_01=R0015094_Fit_Slider_units_Screenshot_2023-06-13_100841.png | |Step_Picture_01=R0015094_Fit_Slider_units_Screenshot_2023-06-13_100841.png | ||
| Ligne 40 : | Ligne 47 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title=<translate></translate> | + | |Step_Title=<translate>Fit support arm spacers to arms</translate> |
| − | |Step_Content=<translate> | + | |Step_Content=<translate>2 off per arm |
| − | + | ||
| − | + | Fix using M8 x 20 hex head Set bolt and finalise with loctite 243 | |
| − | + | ||
| − | + | ||
| − | + | Please provide pictures</translate> | |
| − | + | |Step_Picture_00=R0015253_Fit_Slider_units_Screenshot_2024-09-05_104444.png | |
| − | |||
| − | | | ||
| − | |||
| − | |||
| − | |||
| − | |||
}} | }} | ||
{{Notes}} | {{Notes}} | ||
Version actuelle datée du 5 septembre 2024 à 10:51
Instructions on mounting slider units to support arms
Difficulté
Moyen
Durée
1 heure(s)
Introduction
Tools Required
Standard spanner set
Parts Required
Étape 1 - Unless otherwise stated
Use Loctite 243 on all fasteners
Use Loctite 572 on all threaded pneumatic connections
Pen mark all bolts to show finalised
Étape 2 - Fit slider units to Arms
Slide pre built slider units on rails .
1 Ensure drive pinion is slid away from assembly
2 Use setting dokit Setting Delrin Transfer Table Wheel Tension and set delrin wheels to correct tension. Check at all points over oozenest V rail
3 Repeat for all 9 units
Étape 3 - Fit support arm spacers to arms
2 off per arm
Fix using M8 x 20 hex head Set bolt and finalise with loctite 243
Please provide pictures
Draft
Français
English
Deutsch
Español
Italiano
Português