Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.
Liste de résultats
- 1 Use M5 x 16 socket caps to mount 4 off D00015856 hard stops to double plunge assemblies 2 Use 8 off m4x 12 socket caps and fix to all slide bases as a hard stop +
- 1 Use cylinder stroke adjustment to align … 1 Use cylinder stroke adjustment to align these two faces 2 Apply Loctite 243 to cylinder nut and tighten 3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke 4 Finalise bolts Repeat on all four single spindles (1,3,5 and 7))n all four single spindles (1,3,5 and 7)) +
- 1 Use cylinder stroke adjustment to align … 1 Use cylinder stroke adjustment to align these two faces 2 Apply Loctite 243 to cylinder nut and tighten 3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke 4 Finalise bolts Repeat on all four single spindles (2,4,6 and 8)on all four single spindles (2,4,6 and 8) +
- 4 off 1 Lightly Fix D0007723 motor mount to bearings as shown . Use 8 off M6 x 12 socket caps to fix. 2 Use 0.05mm feeler gauge to check datum faces are in contact, if not remove and inspect parts 3 Finalise bolts <br/> +
- 4 off
1 Attach D0007600 cylinder mount … 4 off
1 Attach D0007600 cylinder mount using 2 off M5 x 20 socket caps
2 Attach lighty pre built cylinder assembly using 4 off M6 x 20 socket caps
3 Attach cylinder thread and adjust stroke of cylinder to achieve measurement of 28mm
4 Adhesive and lock off cylinder nut
5 Use clearance in indicated holes to achieve correct cylinder alignment . Stroke of cylinder should be free and consistent
6 Finalise all bolts
d consistent 6 Finalise all bolts <br/> + - 4 off
1 Attach D0007686 motor plate to … 4 off
1 Attach D0007686 motor plate to elte motor using 4 off m6 x 12 socket caps and 2 off 6mmx 20 dowels
2 Attach to single spindle using 4 off m6 x 16 socket caps
Ensure that motor plate butts up to indicated parts and also register is aligned as shown
3 use 5 off m6 x 20 socket caps used to finalise end plate . ensure mounting is even to motor plate
ure mounting is even to motor plate <br/> + - <div class="icon-instructions caution-i … 4 off 1 Mount D0007687 motor plate to elte motor with 4 off M6 x 12 socket caps and 2 off 6mm x 20 dowels 2 Use 3 off M6 x 30 socket caps and mount elte motor as shownand 2 off 6mm x 20 dowels 2 Use 3 off M6 x 30 socket caps and mount elte motor as shown +
- Check that component D0007649 has been manufactured correctly Indicated hole should be tapped M6. Rework and report if not To M6 tapped spec +
- Do not add final tension to bolts until al … Do not add final tension to bolts until alignment has been achieved
1 Attach pre built cylinder anchor to end of cylinder
2 Position pre built cylinder on slide base assembly as shown
3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base
4 Temporarily mount D0007649 with 1 off m6 x 20 socket cap
5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps
6 Attach Cylinder base to anchor with 4 off M6x 20 socket caps
nchor with 4 off M6x 20 socket caps <br/> + - Do not add final tension to bolts until al … Do not add final tension to bolts until alignment has been achieved 1 Attach pre built cylinder anchor to end of cylinder 2 Position pre built cylinder on slide base assembly as shown 3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base 4 Temporarily mount D0007648 with 1 off m6 x 20 socket cap 5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps 6 Attach Cylinder base to anchor with 4 off M6x 20 socket capsse to anchor with 4 off M6x 20 socket caps +
- Use Loctite 243 on all fasteners Pen mark bolts when finalised +
Français
English
Deutsch
Español
Italiano
Português