Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

'''Adjustable P bracket only< … '''Adjustable P bracket only''' Do not add final tension to bolts until alignment has been achieved 1 Attach pre built cylinder anchor to end of cylinder 2 Position pre built cylinder on slide base assembly as shown 3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base 4 Temporarily mount D0007648 with 1 off m6 x 20 socket cap 5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps 6 Attach Cylinder base to anchor with 4 off M6x 20 socket caps Cylinder base to anchor with 4 off M6x 20 socket caps +
1 Position pre assembled cylinder as shown … 1 Position pre assembled cylinder as shown on spindles 2,4,6 and 8 2 Set P bracket flush on faces indicated and secure with 2 off M5 x 25 socket caps and A form washers . Finalise fasteners 3 Fit D0007790 bracket using 4 off M6x20 socket caps. Set bottom of bracket and bottom of spindle plate flush or parallel . Finalise fasteners 4 Secure base of cylinder as shown using 4 off M6 x 25 socket caps. Finalise fasteners 5 Move assembly by hand to check for smooth running and correct operationk for smooth running and correct operation +
1 Use M5 x 16 socket caps to mount 4 off D00015856 hard stops to double plunge assemblies 2 Use 8 off m4x 12 socket caps and fix to all slide bases as a hard stop +
4 off 1 Lightly Fix D0007723 motor mount to bearings as shown . Use 8 off M6 x 12 socket caps to fix. 2 Use 0.05mm feeler gauge to check datum faces are in contact, if not remove and inspect parts 3 Finalise bolts +
4 off 1 Attach D0007600 cylinder mount … 4 off 1 Attach D0007600 cylinder mount using 2 off M5 x 20 socket caps 2 Attach lighty pre built cylinder assembly using 4 off M6 x 20 socket caps 3 Attach cylinder thread and adjust stroke of cylinder to achieve measurement of 28mm 4 Adhesive and lock off cylinder nut 5 Use clearance in indicated holes to achieve correct cylinder alignment . Stroke of cylinder should be free and consistent 6 Finalise all bolts
d consistent 6 Finalise all bolts +
4 off Spindles 2,4,6,8 1 Attach D0007 … 4 off Spindles 2,4,6,8 1 Attach D0007686 motor plate to elte motor using 4 off m6 x 12 socket caps and 2 off 6mmx 20 dowels 2 Fit D0007648 to each spindle using 3 off M6 x 20 socket caps , apply adhesive but only light tension 3 Attach motor to single spindle using 4 off m6 x 16 socket caps Ensure that motor plate butts up to indicated parts and also register is aligned as shown 4 Finalise D0007648. Glue and fit additional 2 off M6 x 20 socket caps and set faces flush as shown. Finalise fastenerst faces flush as shown. Finalise fasteners +
<div class="icon-instructions caution-i …

...For machine accuracy it is vital the indicated faces butt together. Check with 0.002" feeler gauge to ensure contact

4 off 1 Mount D0007687 motor plate to elte motor with 4 off M6 x 12 socket caps and 2 off 6mm x 20 dowels 2 Use 3 off M6 x 30 socket caps and mount elte motor as shownand 2 off 6mm x 20 dowels 2 Use 3 off M6 x 30 socket caps and mount elte motor as shown +
Adjustable P Bracket only 1 Use cylinder … Adjustable P Bracket only 1 Use cylinder stroke adjustment to align these two faces 2 Apply Loctite 243 to cylinder nut and tighten 3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke 4 Finalise bolts Repeat on all four single spindles (1,3,5 and 7))n all four single spindles (1,3,5 and 7)) +
Adjustable P Bracket only Do not add fi … Adjustable P Bracket only Do not add final tension to bolts until alignment has been achieved 1 Attach pre built cylinder anchor to end of cylinder 2 Position pre built cylinder on slide base assembly as shown 3 Use 2 off m5 x 25 socket caps with A form washers to attach to slide base 4 Temporarily mount D0007649 with 1 off m6 x 20 socket cap 5 Attach D0007790 cylinder anchor with 4 off M6 x 20 socket caps 6 Attach Cylinder base to anchor with 4 off M6x 20 socket caps
nchor with 4 off M6x 20 socket caps +
Adjustable P Bracket only 1 Use cylinde … Adjustable P Bracket only 1 Use cylinder stroke adjustment to align these two faces 2 Apply Loctite 243 to cylinder nut and tighten 3 Use clearance in holes for mounting at points indicated to achieve cylinder alignment. Cylinder stroke should be even and free along entire stroke 4 Finalise bolts Repeat on all four single spindles (2,4,6 and 8)on all four single spindles (2,4,6 and 8) +
Adjustable P Bracket only Spindles 2,4 … Adjustable P Bracket only Spindles 2,4,6,8 1 Attach D0007686 motor plate to elte motor using 4 off m6 x 12 socket caps and 2 off 6mmx 20 dowels 2 Attach to single spindle using 4 off m6 x 16 socket caps Ensure that motor plate butts up to indicated parts and also register is aligned as shown 3 use 5 off m6 x 20 socket caps used to finalise end plate . ensure mounting is even to motor plate
ure mounting is even to motor plate +
Check that component D0007649 has been manufactured correctly Indicated hole should be tapped M6. Rework and report if not To M6 tapped spec +
Fixed P Bracket only 1 Position pre ass … Fixed P Bracket only 1 Position pre assembled cylinder as shown on spindles 2,4,6 and 8 2 Set P bracket flush on faces indicated and secure with 2 off M5 x 25 socket caps and A form washers . Finalise fasteners 3 Fit D0007790 bracket using 4 off M6x20 socket caps. Set bottom of bracket and bottom of spindle plate flush or parallel . Finalise fasteners 4 Secure base of cylinder as shown using 4 off M6 x 25 socket caps. Finalise fasteners 5 Move assembly by hand to check for smooth running and correct operationk for smooth running and correct operation +
This instruction covers the fitting of 2 different styles of cylinder P bracket sets Please see photos for clarity on differences Steps will detail if any specific settings are required for the appropriate style of P bracket being fitted +
Use Loctite 243 on all fasteners Pen mark bolts when finalised +