Rechercher dans les propriétés de la page

Cette page fournit une interface de navigation pour trouver toutes les valeurs d’une propriété et une page donnée. D’autres interfaces de recherche disponibles incluent la recherche de propriété, et le constructeur de requête ask.

Liste de résultats

• 1 Ensure indicated central 4 adjusting b … 1 Ensure indicated central 4 adjusting bolts/ pads are lifted out of the way , so they do not impede the levelling process 2 Set gap of indicated pads to the starting measurement shown of 40mm 3 Adjust Y axis position to read level at indicated points using pads indicated in number 2 only 4 Adjust X axis position using same pads as previous,and ensure Y axis level is not compromised by adjusting pads in pairsnot compromised by adjusting pads in pairs  +
• 1 Centre support foot can now be set on M … 1 Centre support foot can now be set on Machining centre. Insert 2 meter straight edge and bridge 2 datum points for x axis on the machining centre ( same as previous step) 2 If all rollers are contacting straight edge, adjust centre support to take weight of Machining centre but not adjust roller position 3 If discrepancy is visible, centre support can be adjusted to align centre rollers to straight edged to align centre rollers to straight edge  +
• 1 Ensure centre support foot is wound up … 1 Ensure centre support foot is wound up away from floor to not impede initial level setting 2 Use a 2 meter straight edge and engineers level to bridge between 2 indicated datum points for X axis datum . Adjust perimeter pads only to bring this level (centre rollers tables may appear low when straight edge is used. This is normal and will be adjusted out later) 3 Use engineers level on the indicated face to adjust Y axis level. Ensure floor pads are adjusted in pairs to maintain X axis level that has been setto maintain X axis level that has been set  +
• 1 Use 2 meter straight edge against indicated rollers on infeed table . 2 Adjust position of Machining centre so indicated rollers align to straight edge set against infeed rollers  +
• 1 Use a laser to cast from the indicated p … 1 Use a laser to cast from the indicated point in the direction shown 2 Take indicated measurement From roller closest to Machining centre 3 Take the same measurement at the last roller on the Infeed. These measurements need to be the same to ensure correct alignment 4 If the measurement is different, the Machining centre will require adjusting slightly to correct this pivot the Machining centre Rear in the indicated directions to correct laser error 5 Recheck Step 10 if adjustments are made All Previous parameters for alignment must be rechecked (steps 7 to 13) once final adjustments have been done 13) once final adjustments have been done  +
• <div class="icon-instructions info-icon …
  ...Infeed table lift rollers are required to set height relationship to Machining centre. These must be set in the lifted position. Use temporary air supply
  1 Use 2 meter straight edge on indicated rollers to project height to Machining centre 2 Use indicated rollers to accept projection from Infeed table 3 Adjust 4 corner pads of Machining centre equally to match height to straight edge . 4 Increase height of Machining centre by 0.5mm to allow slight bump up from Infeed rollers to Machining centre Machining centre by 0.5mm to allow slight bump up from Infeed rollers to Machining centre  +
• Datums for levels are as shown 1 X Axis . Only first and last datum rollers should be used initially for levelling 2 Y Axis should be set from fixed cut table  +
• Identify correct position for installation of Infeed frame. Ensure consideration is given to walkways and installation of machine guarding at later part of installation  +
• Indicated are the leveling datums for the Infeed table X Axis as indicated by 1 Y axis as indicated by 2  +
• Laser alignment is now required to ensure all alignment is correct 1 Use a laser to cast from indicated rollers in the direction shown 2 Ensure measurement indicated is constant on every roller on infeed table  +
• Now alignment between Infeed table and Machining centre is complete , the front tray support can set Adjust support so front tray is held level to rest of assembly  +
• Position Module B/F into the approximate area according to the floor plan  +
• Remaining pads should now be adjusted down to touch floor. Ensure no additional pressure is applied to they which will cause levels to be affected  +
• Spacing between Infeed and Machining centre should be set to 370mm as indicated. This measurement is taken from internal faces of frame box section.  +
• The JX axis requires assembling to allow setting of the outfeed table  +
• Use footprint drawing to determine machine location for installation  +