WinMulti - IO Screens - Autoflow

Auteur avatarStuga Engineer | Dernière modification 6/04/2020 par Stuga Engineer en cours de rédaction

On an Autoflow machining centre there are 3 IO Screens


  1. 1. IO
  2. 2. IO-Infeed
  3. 3. Spindle IO


each of these has a section below with a table describing each input and output.


Autoflow Main IO Screen


Autoflow Main IO Screen

Autoflow Inputs

Module A – Infeed Table
Sensor Description Sensor Description
InA_GripperOff Gripper Slip Sensor InA_48vOk 48v Ok (No Errors)
InA_Measure1 Offcut Measure Sensor 1 InA_AirOk Air Supply OK
InA_Measure2 Offcut Measure Sensor 2 InA_Grip Gripper Sensor (Profile in place)
InA_GZHome Gripper Z Axis Home InA_EStop Emergency Stop State
InA_GYHome Gripper Y Axis Home InA_ButStart Start Button
InA_GXHome Gripper X Axis Home InA_ButStop Stop Button
InA_MatLoad1 Material Load Sensor 1 InA_ButReset ES Reset Button
InA_MatLoad2 Material Load Sensor 2 InA_ButEstop1 Emergency Stop Button 1
InA_Index Infeed Table Index Position InA_ButEstop2 Emergency Stop Button 2
InA_VCUOk VCU Ok (No Errors) InA_ButEstop3 Emergency Stop Button 3
InA_Bus415Ok Bus415Ok (No Errors) InA_ButAuto Auto Load Button
InA_Bus415SOk Bus415S Ok (No Errors) InA_MatlAtFence Material At Back Fence Sensor
InA_24vBusOk 24v Bus Ok (No Errors) InA_StopOver Profile Stop
InA_24vModOk 24v Module Ok (No Errors) InA_ButLoad Load Button
Module B – Multihead
Sensor Description Sensor Description
InB_YHome Y Axis Home Switch InB_ClampOSH Clamp Outfeed Side Home
InB_ZHome Z Axis Home Switch InB_ClampITH Clamp Infeed Top Home
InB_RHome R Axis Home Switch InB_ClampISH Clamp Infeed Side Home
InB_ClampOTH Clamp Outfeed Top Home InB_OilerOK Oiler OK (No Errors)
Module F – Saw and Outfeed
Sensor Description Sensor Description
InF_SYHome Saw Y Axis Home (forward/back) InF_EjectHm Ejector Home
InF_SZHome Saw Z Axis Home (up/down) InF_EjectOu Ejector Out
InF_SRHome Saw R Axis Home (rotation) InF_AdvanceB
Saw Outfeed Advance Button
InF_EjPushHm Eject Pusher Home InF_InvSawOk Saw Invertor OK (No Errors)
InF_EjPushOu Eject Pusher Out InF_InvExtract Extractor Invertor OK
InF_ClampOTH Clamp Outfeed Top Home InF_ConvOvlO Conveyor Overload
InF_ClampOSH Clamp Outfeed Side Home InF_TiltHm Saw Blade Tilt Home (vertical)
InF_ClampITH Clamp Infeed Top Home InF_TiltOu Saw Blade Tilt Out (tilted)
InF_ClampISH Clamp Infeed Side Home InF_GtOpen Gate Open
InF_RollerITHm Roller Infeed Top Home InF_GtClosed Gate Closed
InF_48vOk 48v Ok (no errors) InF_GuardFront Front Door
InF_24vBusOk 24v Bus Ok (no errors) InF_GuardRear Rear Door
InF_24vModOk 24v Module Ok (no errors) InF_OfFull Outfeed  Full Sensor
InF_ButEstop4 Emergency Stop Button 4

-Autoflow Outputs

Module A – Infeed Table
Output Description Output Description
OuA_CtrlOn OuA_PopUp Profile Stop Popup
OuA_Grip Gripper OuA_StopX Profile Stop In/Out
OuA_GripBlow Gripper Blower BrakesOff Drive Brakes
OuA_LoadBlow LoadBlower OuA_GripTurn Gripper Turned?
Module B – Multihead
Output Description Output Description
OuB_ClampIT Clamp Infeed Top OuB_ClampOS Clamp Outfeed Side
OuB_ClampIS Clamp Infeed Side OuB_ClampOSPos Clamp  Outfeed Side Wide Pos
OuB_ClampISPos Clamp Infeed Side Wide Pos OuB_Oiler Oiler
OuB_ClampOT Clamp Outfeed Top OuB_OilerChn Oiler Chain
OuB_ClampOTPos Clamp  Outfeed Top Tall Pos
Module F – Saw and Outfeed
Output Description Output Description
OuF_ClampIT Clamp Infeed Top OuF_EjectPush Eject Pusher
OuF_ClampITPos Clamp Infeed Top Tall Pos OuF_Conveyor Outfeed Conveyor
OuF_ClampOT Clamp Outfeed Top OuF_Eject Saw Ejector
OuF_ClampOTPos Clamp Outfeed Top Tall Pos OuF_Tilt Saw Tilt On/Off
OuF_ClampIS Clamp Infeed Side OuF_OffBlow Outfeed Blower
OuF_ClampOS Clamp Outfeed Side OuF_Siren Long Length Siren
OuF_ClampITRoll Clamp Infeed Rollers OuF_Gate Long Length Safety Gate



Autoflow Infeed IO Screen


Autoflow Infeed IO Screen


Autoflow Spindle IO Screen


Autoflow Spindle IO Screen

Commentaires

Draft