Stuga Batch Cutting List Specification

Auteur avatarGareth Green | Dernière modification 3/10/2022 par Gareth Green en cours de rédaction

Saw / Machining Centre Cutting List File Format

1. File Format

The file is ASCII and consists of various types of records. Each starts with an identifying letter and ends with CR, LF. The fields are separated by a comma. The contents depends on the record type.

Structure

Batch record {
    Load records {
        Piece records {
            Operations records {
            }
        }
    Remainder record
}


The batch record is written at the start of the batch and contains general header information. Load records are written whenever stock details change; they contain all information required to load the correct stock. Piece records contain sawing information and other details relevant to each cut piece. Operation lines are written where there is additional machining work to be carried out, e.g. drilling, notching, routing. There may be many operation lines per piece.

Field Format Example Notes
Batch Record
Record Type 1A B
Batch No 8A 12JN9101 Specified in computer
Status 1A S Manufacturing stage
Load Record
Record Type 1A L
Stock No 10A AB1000 Profile stock number
Colour 5A WHITE Profile colour
Pairing N 1 1 = single, 2 = pair (singles only)
Length 5N 60000 Stock Length
Quantity 3N 012 Number of pairs or singles to load
Piece Record
Record Type 1A P
Length 5N 10000 Cut length
Sawcut 2A <> Two of  | [ ] \ / < >
Trolley No 2N 02 Trolley Number
Slot No 2N 17 Position on trolley
Identification 40A ASD100/001/F^A1 Job / Item / Position in window
Cut Angle L 4N 0900 Angle at left end
Cut Angle R 4N 0900 Angle at right end
Piece No 12N 000000000112 Unique piece number. Should start a 1 for the first piece in the batch and increment up.
Operation Record
Record Type 1A O
Position 5N 02340 Distance from start of piece
Tooling Code 8A DFR Operation name
Param 1 3N 0 }
Param 2 3N 0 } Currently unused
Param 3 3N 0 }
Remainder Record
Record Type 1A R
Length 5N 00100 Length of offcut
Sawcut 2A || Cut type if req.
Destination 1A W W = Waste, S = Store
Piece No 12N 000000000000 Unique piece no

Format Notes

a)     All lengths are in tenths of mm.

b)    Angles in tenths of a degree

c)     Pieces are included, even if there are no operations

d)    Numeric fields have leading zeros. Alphanumeric fields are left justified an padded with spaces.

e)     The Piece No is used for tracking. It cross-references with the number printed on a label. This can be input by a user or scanned with a bar-code reader.

f)     If pair cutting, there will still be one record per piece. The identification numbers still have to be carried, and there may be operations to carry out.

g)    There will be one (two for pairs) remainder records per bar, even if the length is zero.

h)    The parameters for operation lines depend on the type of operation.

i)      To minimise wastage, alternating from arrowhead to square cuts should be avoided.


File Name

The file name output by software supplier will be “bbbbbbbb.449” where “bbbbbbbb” is the batch number. Note that the batch number should be read from the batch record.

Programming Notes

To allow for future enhancements, any program reading this file should follow these guidelines.

a)     Allow for possibility of more than one batch record, allowing batch records to be concatenated.

b)    Allow fields to be of variable length.

c)     Ignore any extra fields.

d)    If the saw cannot cut arbitrary angles, the angle to cut may be obtained from the ‘Saw Cut’ field.

Records that are not required may be ignored.


Example File

B,Test23rd.449,S
L,BLR56E   ,WHITE,1,60000,001
P,12340,\/,00,00,BR129A/001/F_A1     ,0450,0450,000000002685
P,12340,\/,00,00,BR129A/001/F_A1     ,0450,0450,000000002686
P,20000,\/,00,00,BR129A/001/F_A1     ,0450,0450,000000002687
O,00100,DFR,000,000,000
O,00150,DRR,000,000,000
O,10000,ESP,000,000,000
O,19830,DRR,000,000,000
O,19880,DFR,000,000,000
P,20000,\/,00,00,BR129A/001/F_A1     ,0450,0450,000000002688
R,47160,[],S,100000000437


The above file illustrates loading a single bar of 6000 mm, cutting 4 pieces, one of which has 4 operation lines - 2 drain entry slots, 2 drain exit slots and an espag prep in the middle. An offcut of  4176mm is stored.

2. Profile Orientation

All profiles follow these rules:

  • Large face always goes to the bottom, outside of frame to rear
  • Eurogroove always goes to the rear
  • Leg on Z sashes / transoms always at bottom
Stuga Batch Cutting List Profile Orientation.png
...The operation position should always be given from the left hand end.
Stuga Batch Cutting List Operation Position.png


3. Operations

The machining centre has a very flexible method for programming operations. The operations take the form of a CNC program stored on the machining centre. The programs are referred to by a tooling code. An operation can be as simple as a spot for a friction stay or as complicated as a 5 point door lock prep. The window designing package simply has to output the tooling code and the position along the bar. The machining centre handles all the profile related positional and size information. Each operation has a standard start position. The list of tooling codes for a particular system will be supplied to the window design software company by Stuga at least two months before the machine installation date. Certain standards are used to name the tooling codes.

3.1 Drainage

The tool codes for the drainage operations are the same for every profile. Each profile will have up to six different types of drainage.

Drainage Type Tool Code
Drain Front Rebate DFB
Drain Rear Rebate DRR
Drain Front Bead DFB
Drain Rear Bead DRB
Drain Top Face DTF
Drain Bottom Face DBF


3.1.1 Outer Frame

Stuga Batch Cutting List Specification Outer Drainage.png


3.1.2 T Transom

Stuga Batch Cutting List Specification Transom Drainage.png


3.1.3 Z Transom

Stuga Batch Cutting List Specification Z Transom Drainage.png


3.1.4 T Sash

Stuga Batch Cutting List Specification T Sash Drainage.png



3.1.5 Z Sash

Stuga Batch Cutting List Specification Z Sash Drainage.png


The start position of drain operations is the leading side of the drain slot as it enters the machine. This makes calculating the operation position a little more difficult, but it allows the slot to be cut in one pass, greatly increasing the efficiency of the Flowline.

3.2 Espags

The espag prep is normally done in one operation. As a company normally has one espag and one shootbolt hardware on each profile, the tooling codes are normally:


ESP - Espag

SHB - Shootbolt


The start position of the operation is the centre of the prep.

3.3 Trickle Vents

Each vent hardware will have a different tooling code. The start position is in the centre of the operation.

3.4 Door Handles / Gearboxes

The door handle prep including gearboxes is done in one operation. The start position is the spindle centerline.

For each distinct door lock there are two tooling codes for the two possible directions that the operation can face. There are four possible door formats (open in / open out coupled with left hand or right hand hung) which can be made with the two tooling codes. It will depend on the profile type as well as the door orientation as to which direction an operation will face.


Use a P suffix for ‘positive’ doors and the distance to the handle centerline will be measured as

Stuga Batch Cutting List Specification Door P.png


eg tooling code will be doorP


Use an N suffix for ‘negative’ doors and the distance to the handle centerline will be measured as is

Stuga Batch Cutting List Specification Door N.png


eg tooling code will be doorN

3.5 Door Keep Preps

As with the doors, the door keeps are machined in one whole operation. For each pair of door preps there will be an equivalent pair of keep preps (if required)

3.6 V Notches and Y Notches

V Notches are classed as operations and have a standard code. Y notches are the half of a V notch added to the end of a reverse butt prep to give the full V notch when welded.


Format:

               NotchCode followed by depth of notch in 10ths mm


Notch Codes

Description Code View from top
Full V notch in front VFnnn
Stuga Batch Cutting List Specification Image.png
Full V notch in rear VRnnn
Stuga Batch Cutting List Specification V Rear.png
Y notch in front right YFRnnn
Stuga Batch Cutting List Specification YFR.png
Y notch in front left YFLnnn
Stuga Batch Cutting List Specification YFL.png
Y notch in rear right YRRnnn
Stuga Batch Cutting List Specification YRR.png
Y notch in rear left YRLnnn
Stuga Batch Cutting List Specification YRL.png


The position should be given to the point of the notch from the loading end (ie left-hand end in above diagrams). This will mean that Y notches will either have a position of zero or (part length).


Points to note:

  • The Stuga Flowline has two separate blades that can be worked independently. A Y notch prep can be placed anywhere on a piece without interference to the adjacent piece.
  • The ZX5 has 2 blades that work simultaneously to create a V notch. Y notches are made on the sawing side

3.7 Other Operations

The Flowline is capable of an unlimited number of other operations. These can take the form of spot preps, hinge preps, casement keeps, door packers, hinge bolts, etc. These will be defined for each installation.

4. Bar Usage

The Stuga Flowline optimises the batch for use of profile automatically as standard. The Stuga sawing centre has optimising as an optional extra. If optimising is not installed, the following rules should be followed to optimise the batch before cutting.

4.1. Trim Cut

The saw allows a trim cut at the beginning of the bar. It is adjustable from the 'Machine Parameters' option.- For more information see the operating manual. It is usually set to 10 mm to allow for inconsistent length and squareness of profile available from the manufacturer.

4.2. Piece to Piece gap

The machine keeps the gap in between pieces as small as possible (equal to the kerf). Because of the way cuts are made, however, some piece to piece gaps are larger. The following table lists the piece gaps, for reference when programming optimisation packages.

Stuga Batch Cutting List Specification Gaps.png


As the table shows, it is most economical to avoid arrow head cuts on the left-hand side of the cut length, except when cutting another arrow-head.

5. Printer File Format

For customers who require extra information on the labels, the link should be set up to generate a separate printer file. This file provides a reference for a label format for each piece in a batch of windows.

5.1 Structure

The file is ASCII text:


Batch record {
    Piece records {
        Label records {
        }
    }
}

The batch record is written at the start of the batch and contains general header information exactly like the cutting list. Piece records are written exactly as the cutting list. Label records contain the bare text for printing onto the label. There can be up to 8 Label records per piece.

5.2 Format

Field Format Example Notes
Batch Record
Record Type 1A B
Batch No 8A 12JN9101 Specified in computer
Status 1A S Manufacturing stage
Piece Record
Record Type 1A P
Length 5N 10000 Cut length
Sawcut 2A <> Two of  | [ ] \ / < >
Trolley No 2N 02 Trolley Number
Slot No 2N 17 Position on trolley
Identification 40A ASD100/001/F^A1 Job / Item / Position in window
Cut Angle L 4N 0900 Angle at left end
Cut Angle R 4N 0900 Angle at right end
Piece No 12N 000000000112 Unique piece number
Label Record
Record Type 1A X
Label Text 80N Any ASCII text Text will be printed line by line


Format Notes

a)     All lengths are in tenths of mm.

b)    Angles in tenths of a degree

c)     Numeric fields have leading zeros. Alphanumeric fields are left justified an padded with spaces.

d)    The Piece No is used for tracking. It cross-references with the piece number from the cutting list.


File Name

The file name output by software supplier will be “bbbbbbbb.prn” where “bbbbbbbb” is the batch number. Note that the batch number should match the batch number of the cutting list.


Example File

B,00001256.prn,S
P,12340,\/,00,01,BR129A/001/F_A1     ,0450,0450,000000000001
X,    Customer: Mrs Jones
X,    Location: Lounge 
X,        ------------------------------------------
X,        \               0906 mm                  /
X,         \                                      /
X,         --------------------------------------
X,                                 Reinforcing: None
P,12340,\/,00,02,BR129A/001/F_A1     ,0450,0450,000000000002
X,    Customer: Mrs Jones
X,    Location: Lounge 
X,       ------------------------------------------
X,        \               1206 mm                  /
X,         \                                      /
X,         --------------------------------------
X,                                 Reinforcing: 1000 CRS
P,20000,\/,00,02,BR129A/001/F_A1     ,0450,0450,000000000003
X,    Customer: Mrs Jones
X,    Location: Lounge 
X,        ------------------------------------------
X,        \               0906 mm                  /
X,         \                                      /
X,         --------------------------------------
X,                                 Reinforcing: None
P,20000,\/,00,08,BR129A/001/F_A1     ,0450,0450,000000000004
X,    Customer: Mrs Jones
X,    Location: Lounge 
X,       ------------------------------------------
X,        \               1206 mm                  /
X,         \                                      /
X,         --------------------------------------
X,                                 Reinforcing: 1000 CRS

6. Reiniforcing Field

Addition - June 2022

Requirement is for a field to determine if reinforcing is used in order to sort the cut pieces into two sections.

Given the assumption that "Zeb" label printing will be active (ie the 3rd party software company outputs the label data), this will mean that the id field is not required for "important" data. Therefore additianal data can be added to signify the reinforcing type used.

Add the string "$R" to the id field. The software will search for this string anywhere in the field

P,20000,\/,00,00,BR129A/001/F_A1   $R,0450,0450,000000002687

Commentaires

Draft