R0015310 Install V Notch Subframe

Auteur avatarGareth Green | Dernière modification 3/04/2024 par Gareth Green en cours de rédaction

Introduction

Tools Required


Standard hex key set

Standard Spanner set

Parallel setting blocks

600mm rule

1 meter straight edge

2 meter straight edge

12 " engineers level

12" engineers square


Parts Required


D0015151 Shaft End Washer x 8

D0015155 Vertical Spacer Bar x 4

D0015150 shaft 40mm zx v notch x 4

D0015169B cylinder rod bracket x 2

R0015035 Bench Assemble V Notch Components

Étape 1 - Unless otherwise stated

Use locktite 243 on all fasteners

Use loctite 572 on all threaded pneumatic connection

Pen mark all fasteners to show finalised



Étape 2 - Install top Mount

Position top mount as shown


1 Use 4 off M12 x 25 socket caps and A form washers to lightly fix in position


2 Adjust 8 off M10 grubscrews to lift mount approximately 1mm from face of mounting block


Étape 3 - Level top mount

1 Level X axis on both ends as shown using parallels and engineers level , Use M10 grubscrews to adjust


2 Level Y axis as shown , using 1 meter straight edge and parallels. Use M10 grubscrews to adjust


3 Ensure M12 socket caps are tight and recheck levels once set


Étape 4 - Fit shafts

1 Fit 4 off D0015150 shaft 40mm zx v notch as shown , shafts must be staggered as shown


2 Captivate in position with M8 x 12 flat grubscrews in top mount blocks


Étape 5 - Caution

When fitting bearing assemblies, great care should be taken to preserve bearing seals.


Ensure seals are not damaged by folding or kinking during installation



Étape 6 - Add top bearing block

Fit top bearing block as shown.

...Ensure correct orientation!!

See photos for orientation


Fit shaft clamp to 1 off shaft to hold bearing block in position

Étape 7 - Fit rear lower bearing block

Fit lower bearing block as shown to rear of frame


Take care to orientate correct way


Identify by cut out indicated


Secure with Shaft clamp as shown


Étape 8 - Fit front lower bearing block

Fit front lower bearing block as shown


Ensure correct orientation


Use counter bores holes as reference, these should be facing up


Secure with shaft clamp



Étape 9 - Position Bottom support

Lay in position bottom support as shown


Do not fix at this point



Étape 10 - Drop outer shafts

1 Individually drop 2 outer shafts


Release locking M8 grubscrew to allow movement


2 Position shafts just above bottom support as shown


Étape 11 - Add top washers

1 Fit 2 off D0015151 Shaft End Washer to outer shafts. Use M16 x 2.0 x 30 set bolt to secure


2 Drop outer shafts individually to start penetrating the bores of the lower support blocks (by approx 5mm )


3 Fit 2 off D0015151 Shaft End Washer with M16 x 2.0 x 50 set bolts to shaft bottom


4 Use set bolts to evenly pull lower blocks onto outer shafts


5 Adjust shafts down from top fixing so washers now sit flush to mounting block


6 Swap bottom outer shaft fixing M16 x 2.0 x 50 For M16 x 2.0 x 30 set bolt and position block as shown (slight gap between support angle and main frame)

Étape 12 - Drop inner shafts

Individually swap shaft clamps to outer shafts (use clamp to hold bearing block when removing shaft clamp )


Repeat step 11 to position inner shafts

Étape 13 - Position bearing assemblies

Reposition bearing assemblies as shown


1 Drop lower rear bearing block by releasing shaft clamp and dropping to shown position


2 Add clamp to hold top bearing block to upper mount


3 Drop front lower bearing block to same height as rear lower and secure with shaft tie


4 Drop upper bearing block to position shown



Étape 14 - Fit vertical spacers

1 Lift upper bearing assembly


2 Position 4 off D0015155 Vertical Spacer Bar as shown


3 Drop upper bearing assembly onto fitted spacers


Étape 15 - Add lower fixings

Use 4 off M8 x 50 socket caps with M8 A form washers to fix spacer shafts at positions shown



Étape 16 - Add upper fixings

Commentaires

Draft