R0015060 Bench Assemble Flapper Beam

Auteur avatarGareth Green | Dernière modification 3/04/2024 par Gareth Green en cours de rédaction

Introduction

Tools Required


Standard hex key set


Parts Required


B0001099 Bush flange 10 i/d 12 o/d x 14

C0001018 EP2338-0001 EtherCAT Box 8 Configurable IO x 1

D0010167 Ethercat Mount Plate x 1

D0015353 Sensor Flapper Pivot x 8

D0015355 Sensor Flapper Plate (312) x 6

D0015357 Sensor Flapper Plate (270) x 1

D0015363 Sensor Flapper Support Transfer SEE NOTE x 1

D0016322 Welded 90° Bracket: 76mm x 38mm x 38mm x 2

E0000336L Sensor: M8; 4mm, PNP N/O, M8 conn x 7

F0000537 dowel pin 10 x 40 x 8

M0001016 Angle 74 x 38 x 2

M0001209 Bracket m8 proximity sensor bracket 90 deg x 7



Étape 1 - Unless otherwise stated

Use Loctite 243 on all fasteners

Use Loctite 570 on all threaded pneumatic connections

Pen mark all bolts when finalised



Étape 2 - Quality check

Check components


D0015355 Sensor Flapper Plate (312) x 6

D0015357 Sensor Flapper Plate (270) x 1


Ensure indicated have a radius on the indicated faces and are smooth and burr free



Étape 3 - Assemble Maytec frame

Assemble frame as shown


Set leg 1 to 405mm


Set leg 2 to 305mm

Étape 4 - Fit bushes

Fit B0001099 Bush flange 10 i/d 12 o/d x 14 into D0015355 Sensor Flapper Plate (312) x 6 and D0015357 Sensor Flapper Plate (270) x 1 as shown


Étape 5 - Fit 1st Pivot

Fit 1st D0015353 Sensor Flapper Pivot as shown


Fix with F0000299 m6 d nut and M6 x 20 socket cap


Étape 6 - Add dowel

Fit F0000537 dowel pin 10 x 40 as shown, leaving 5mm of protrusion


Secure with M5 x 12 kcp grubscrew


Étape 7 - Fit 1st plate

1 Position as shown D0015357 Sensor Flapper Plate


2 Captivate with pivot block and dowel as shown, using same fixings as previous pivot block . Ensure dowel sits central in pivot block.

3 Ensure sensor plate is free to move in the direction shown when fitted. Leave as minimal gap as possible between pivot blocks and sensor plate



Étape 8 - Fit 2nd plate

Fit D0015355 Sensor Flapper Plate (312) and fix with same method as previous steps




Étape 9 - Repeat for remaining plates

Fit remaining 5 plates in the same method as shown


Étape 10 - Fit sensors

1 Fit 7 off M0001209 Bracket m8 proximity sensor bracket 90 deg. Position each bracket centrally beneath each sensor plate and orientate as shown


Use M5 fat D nut, M5 x 10 socket cap and A form washer to secure


2 Fit 7 off E0000336L Sensor: M8; 4mm, PNP N/O, M8 conn as shown .


3 Set sensor gap to 5mm


With the sensor plate fully depressed in the direction shown, set sensor so 5mm gap is present


4 Secure 2 off lock nuts on sensor. Caution do not over tension, as this can lead to damage to sensor !


Étape 11 - Fit tie bases

Fit Cable tie bases using M5 x 10 button sockets an M5 fat D nuts at the positions shown


(cables shown are fitted at a later stage)


Étape 12 - Assemble and mount Ethercat box

1 Assemble C0001018 EP2338-0001 EtherCAT Box 8 Configurable IO onto D0010167 Ethercat Mount Plate x 1 as shown using M3 x 20 pan head fasteners


2 Fit to assembly Using 2 off M6 fat D nuts , M6 x 16 socket caps and A form washers at the position shown of 590 mm from indicated face to edge of ethercat mounting plate


Étape 13 - Fit support angles

Fit 2 off M0001016 Angle 74 x 38 as shown


Fasten with M8 Fat D nut, M8 x 20 socket cap and Heavy M8 motor plate washer



Étape 14 - Quality check

Ensure all fasteners are double checked for correct tension, adhesive and identification to show finalised



Commentaires

Draft