R0015034B ZX5 Module B Wiring Loom installation Part 3

Installation steps for Electrical looms installation into Module B

Difficulté

Hard Difficile

Durée

1 minute(s) minute(s)

R0015034B_ZX5_Module_B_Wiring_Loom_installation_Part_3_Screenshot_2024-02-21_085621.png

Introduction

Parts Required

Pre labelled Wiring loom assembly R0015034B from electrical team

Tools required

Flush cutters

Tie wraps small

Tie Wraps Large

Étape 1 - Unless otherwise stated

All bolts to have Loctite 243 adhesive applied unless otherwise stated

All Threaded Pneumatic connections to have Loctite 570 applied

All bolts to be pen marked once adhesive applied and correct tension added

Étape 2 - Route Pre made 300hz connection

Route as shown power connection from wiring loom assembly

Z105 onwards as pictures

Z104 and below Different style plug mounted internally in trunking

Route cable to rear of machine as shown

Étape 3 - Handing guide

Please diagram to determine handing positions of machine sections

Étape 4 - Guard switches

Use pre wired guard switches from wiring loom box

CB45B Front interlock guard switch

Cb46B Rear interlock guard switch

Use diagram to determine position

Run cable to rear exits of machine

...Gaurd switches will be fixed into position at a later point

Étape 5 - Route Network cables

Route yellow and green network cables from loom box as shown

Cables route from Rear outfeed to rear infeed as shown .

Please clarify length of cable to be left extended from front or back of machine please

Étape 6 - Route 25way cable

Route 25way cable as shown. Route from Rear Infeed to Rear outfeed positions

Male plug to be positioned at Rear infeed position as shown

Étape 7 - V notch Motor Cables and VY Datum

Use cables

CB01B for connection to VI motor

CB02B for connection to VO motor

CB03B for connection to WI motor

CB04B for connection to WO motor

and already installed Cable x120

Motor identification should be determined by diagrams shown

Étape 8 - Route V notch motor cables and X120 1st energy chain

Route Cables as shown , to first energy chain , then through energy chain to exit point

Ensure cable retention points on energy chain brackets are used

Étape 9 - Route V notch motor cables, SY servo cable and X120 2nd energy chain

Use Servo cable identified V axis from wiring loom box, and incorporate with previous step cables to enter next energy chain .

Ensure cables are as shown and cable retention bracket is used to enable cables to be kept flat once fitted

Exit cables from top of energy chain

Étape 10 - Route V notch motor cables, SY servo cable and X120

Route 4 off green cables and x120 into trunking through 2 off 20mm grommit holes

Route servo cable as shown on cable tie bases

Ensure large cable base is fitted and used at indicated point

Exit cables at rear of machine

Étape 11 - Door Hinge safety cables

Use step 3 for correct identification of positions required

Use 4 off cables from wiring loom box

CB40B Front Infeed Hinge

CB41B Front Outfeed Hinge

CB42B Rear Infeed Hinge

CB43B Rear Outfeed Hinge

Ensure Tie base is used as shown , and star grommits are used for cable entry and exit through main frame work

All Cables to exit at rear of machine

Étape 12 - Camera Ring

Use cable from loom box labelled EN04B

Run from vertical trunking and exit cable at rear of machine

Étape 13 - Camera Infeed

Use cable from loom box labelled EN05B

Run from vertical trunking and exit cable at rear of machine

Étape 14 - Camera Outfeed

Use cable from loom box labelled EN06B

Always fitted same side of machine as previous 2 fitted camera cables

Run from vertical trunking and exit cable at rear of machine

en none 0 Draft