Alignment and fitment details for cut tables and eject drive
Auteur Gareth Green | Dernière modification 3/04/2024 par Gareth Green en cours de rédaction ⧼frevu-button-review-label⧽
Alignment and fitment details for cut tables and eject drive
R0000571_Fit_and_Level_Cut_Tables___Finalise_Eject_Screenshot_2023-10-18_134828.png
Tools Required
1 meter straight edge
500mm rule
Standard hex key
Standard spanner set
Feeler gauges
Engineers level
Adjustment shim
Parts Required
A0001069 Energy Chain Series B15.050 (48mm radius) Openable x 0.5
A0001070 Igus Mounting Br Set for A0001069 Non-Pivot x 1
A0001074 igus mounting bracket set x 1
D0004551 Cylinder Spacer x 1
D0004553 Cover Fixing Bar x 1
D0004554 Bar Spacer Short x 1
D0004555 Bar Spacer Long x 1
D0004769 Ejector Clamp Pad to be made in conjuction with D5121 (5305) x 1
D0004770 Infeed Clamp Pad to be made in conjunction with D5122 (5299) x 1
D0005121 Ejector Clamp Stainless Pads (5306) x 1
D0005122 Infeed Clamp Pad (5300)x 1
D0005199 Ejector Cover x 1
D0005412 Energy Chain Adapter Plate x 1
H0004556 Fixing Bar Gap Cover (5297) x 1
H0004656 Material Trip Stripx 1
P0000368 Extension 1/8 bsp x 22 long x 1
P0000443 Cleanline Cylinder 32 x 450 PN11246 x 1
P0000444 Reed Switch: Pneumax 1580U (5.0m Lead) x 2
P0001198 flow controller 6mm elbow 1/8 x 2All bolts to have Loctite 243 adhesive applied unless otherwise stated
All Threaded Pneumatic connections to have Loctite 570 applied
All bolts to be pen marked once adhesive applied and correct tension added
Attach Infeed pad
Use engineers level to check level
Add shim if required to adjust
Attach Eject pad using m6 ? socket caps
Do not apply adhesive, do not apply final tension
Use infeed pad as datum
Use 1 meter straight edge and feeler gauges
Adjust eject table to suit infeed pad
Set front alignment using adjustment in counter bores in pads
Use 1 meter straight edge and feeler gauges to set
Use Steel rule to measure from pads to rear fence mount on frame from both tables
This measurement needs to be the same
Use adjustment in pads, and pillar supports to correct
Ensure front alignment of tables is held when adjusting
Finalise all fasteners with 243 and correct tension once adjustments are complete
fit eject cylinder with spacer
Ensure alignment
Ensure correct position of cylinder thread adjustment
Fit energy chain with backing plate.
Ensure pivoting bracket is fitted to correct end
Fit cover fixing bar with 2 off spacers and M8 sockets
Tap holes to clean m5 threads
Use infeed pad as datum
Use 1 meter straight edge and feeler gauges
Adjust eject table to suit infeed pad
Set front alignment using adjustment in counter bores in pads
Use 1 meter straight edge and feeler gauges to set
Use Steel rule to measure from pads to rear fence mount on frame from both tables
This measurement needs to be the same
Use adjustment in pads, and pillar supports to correct
Ensure front alignment of tables is held when adjusting
Finalise all fasteners with 243 and correct tension once adjustments are complete
fit eject cylinder with spacer
Ensure alignment
Ensure correct position of cylinder thread adjustment
Fit energy chain with backing plate.
Ensure pivoting bracket is fitted to correct end
Fit cover fixing bar with 2 off spacers and M8 sockets
Tap holes to clean m5 threads
en none 0 Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #